wheel bolts FIAT ULYSSE 2007 2.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2007, Model line: ULYSSE, Model: FIAT ULYSSE 2007 2.GPages: 254, PDF Size: 3.42 MB
Page 156 of 254
IN AN EMERGENCY
155
An incorrectly posi-
tioned jack may cause the
vehicle to fall. Do not use
the jack to lift loads exceeding
that indicated on the label at-
tached to the jack itself.Do not lubricate the bolt
threads before fitting
them back: they could
come loose.
Never start the engine when the
vehicle is jacked up.
If you are towing a trailer, re-
move the trailer before jacking
up the vehicle.Never tamper with the
inflation valve. Never
place tools between the
rim and the tyre.
Check the tyre and space-saver
spare wheel pressure regularly.
The tyre inflation pressure is
shown in the “Technical specifi-
cations” chapter.
The jack should only be
used to change a wheel
on the vehicle for which it
was designed. It should not be put
to other uses or employed to
raise other models. Under no cir-
cumstances should it be used
when carrying out repairs under
the vehicle.
Check the inflation pres-
sure of the tyres and the
spare wheel regularly. If
you change the type of wheels (al-
loy rims instead of steel rims) you
will have to change the entire set
of fastening bolts with another
set of suitably sized bolts.
You should keep the bolts in
case you decide to use the origi-
nal type of wheel later on.Signal the presence of
the stopped car according
to the laws in force: haz-
ard lights, reflecting triangle, etc.
Any passengers on board should
leave the car, especially if it is
heavily laden. Passengers should
stay away from oncoming traffic
while the wheel is being changed.
If the wheel is being changed on
a steep or badly surfaced road,
place wedges or other suitable
material under the wheels to
stop the car.
GENERAL INSTRUCTIONS
Observe the instructions on this and
the following pages to use the jack and
space-saver spare wheel correctly.
Page 158 of 254
IN AN EMERGENCY
157
9) Use handle A-fig. 5to loosen the
spare wheel bolt B.
10) Release support Cto remove
the spare wheel and close the tailgate.11)Remove the wheel cap A-fig. 6
(for versions with steel rims) or the
clipped wheel hub cap (for versions
with alloy rims) by means of tool B
supplied with the car and housed in
the jack container.
12)Loosen the bolts fastening the
wheel to be changed by approximate-
ly one turn. Use the specific supplied
tool A-fig. 7to remove the antitheft
bolt.13) Turn the jack handle to open it
partially and position the jack near the
wheel to be changed.
14)Make sure that the groove A-
fig. 8on the jack is well fitted on the
ribbing Bon the side member.
fig. 5
F0B0120b
fig. 6
F0B0121b
fig. 7
F0B0122b
Page 159 of 254
IN AN EMERGENCY
158
15)Warn other passengers that the
vehicle is about to be raised; all per-
sons should be kept away from the ve-
hicle until it has been lowered.
16)Turn the jack handle and raise
the vehicle until the wheel is a few
inches off the ground. Make sure the
jack handle can be turned easily and
take care not to scrape your hand
against the ground.17)The moving parts of the jack
(screw and joints) may also cause in-
jury if touched. Clean off any grease.
18)Loosen the five bolts complete-
ly and remove the wheel.
19)When fitting the spare wheel,
make sure the hub is clean so that the
bolts will not loosen.
20)Fit the spare wheel making one
of the holes A-fig. 9coincide with pin
B. Now tighten the five wheel bolts
with the handle .
21)Lower the vehicle by turning the
handle and remove the jack.22)Fasten bolts completely, work-
ing in a criss-cross fashion as shown in
fig. 10.
23)Refit the wheel cap (where fit-
ted) and make groove A-fig. 11match
with the wheel inflation valve.
fig. 8
F0B0123bfig. 9
F0B0124b
fig. 10
F0B0125b