air condition FIAT ULYSSE 2009 2.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2009, Model line: ULYSSE, Model: FIAT ULYSSE 2009 2.GPages: 254, PDF Size: 3.56 MB
Page 60 of 254
GETTING TO KNOW YOUR CAR
59
If the warning light either stays on or
comes on while travelling:
fixed light- warning of a fuel
feed/ignition system failure which may
increase emissions in exhaust or cause
possible drops in performance, poor
handling and high consumption.
In such conditions, you can continue
driving but you should not tax the en-
gine and you should moderate the
speed. Prolonged use with the warning
light on can cause damage. Contact a
Fiat Dealershipas soon as possible.
The warning light goes off if the fault
disappears but it is however stored by
the system.
flashing(only petrol versions) -
warning that the catalyser can be dam-
aged (see “EOBD system” in this chap-
ter).
If the warning light starts flashing, re-
lease the accelerator pedal and slow
the engine until the warning light stops
flashing. Continue driving at moderate
speed, preventing the warning light
from coming on again. Contact a Fi-
at Dealershipas soon as possible. AIR BAG
MALFUNCTION
(Amber)
When the system is inefficient.
When you turn the ignition key to
the Mposition the light comes on. It
should, however, go out after about
4 seconds.
¬
Contact a Fiat Dealer-
ship as soon as possible if
the warning light either
does not come on when the key
is turned to M or comes on, with
fixed or flashing light, when trav-
elling.
If the warning light ¬
does not turn on when
turning the ignition key to
M or if it stays on when travelling,
this could indicate a failure in safe-
ty retaining systems; under this
condition air bags or pretension-
ers could not trigger in the event
of collision or, in a restricted num-
ber of cases, they could trigger ac-
cidentally. Stop the car and con-
tact Fiat Dealership to have the
system checked immediately.
FRONT PASSENGER
AIR BAG
DEACTIVATED
(Amber)
With the front passenger air bag ac-
tivated, the light comes on when you
turn the ignition key to M, but it
should go out after about 4 seconds.
Warning light
“indi-
cates also warning light
¬
failure. This is indicated
by intermittent flashing, over 4
seconds, of warning light
“. In
this event, warning light
¬could
be not up to indicate restraint
system failures, if any. Stop the
car and contact Fiat Dealership
to have the system checked.
“
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 59
Page 68 of 254
GETTING TO KNOW YOUR CAR
67
CLIMATE CONTROL (cooling)
Proceed as follows:
- turn the slider pointer Bto the blue
section;
- press button Fto turn the climate
control compressor on and button G
to turn on inside air recirculation;
- turn the slider pointer Ato the re-
quired speed.
• fan speed setting: this is possi-
ble by turning slider A.
• air distribution selection: this is
possible by this is possible by turning
slider E.
Air can be distributed in five
ways: ventilation (front), bilevel
(front/feet), feet, windscreen/feet,
windscreen (MAX-DEF).
• compressor on/off: if the com-
pressor is turned off by pressing but-
ton Nwhen the led is lit, the related
led will go off; if the same button is
pressed when the led is switched off,
the compressor (on/off) is on.• MAX-DEF on: this is possible by
pressing button Dand window
demisting will be quickly reached.
• rear heated window on: this is
possible by pressing button C, and the
related led comes on. In this way the
rear window electrical resistances are
activated to heat and demist the rear
window. To stop it, press the button
again and the related led will go off.
Anyway, the rear heated window
works for a limited time and turns off
automatically.Be careful not to dam-
age the rear heated win-
dow resistances when
cleaning it from inside.
• recirculation on: when button G
is pressed it is possible to select the
following travelling conditions: closed
recirculation (relative led on), air com-
ing from outside (led off) recirculation
open, or having the system automatic
control on (led off even if activated).
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 67
Page 69 of 254
GETTING TO KNOW YOUR CAR
68
The system uses refrig-
erant R134a as it will not
pollute the environment
if it accidentally leaks. Under no
circumstance use other fluids
which are incompatible with the
system’s component parts.
AIR FLOW
The system manual operation has 8
different air capacity levels which are
displayed with half blackening of each
main fan symbol stake.
When the automatic function has
been enabled (AUTO) the air capaci-
ty varies and can be controlled by the
system. This is indicated on the display
by 4 half blackened stakes. It is easier to reach the
wished air temperature
conditions with inside air
recirculation. Anyway, it is better
not to use this function in
rainy/cold days because inside
window misting may increase, es-
pecially if the compressor is off.
You are recommended
to use the inside air recir-
culation function in the
traffic jam (car lines inside or out-
side galleries) to prevent outside
polluted air from getting into the
vehicle. Anyway, do not use this
function when several people are
onboard, to prevent inside win-
dow misting.AUTOMATIC
CLIMATE CONTROL
SYSTEM
The car is fitted with an automatic
climate control system to control tem-
perature, air capacity, distribution and
recirculation according to two defini-
tion levels:
• automatic system called multi-
zone, with split temperature (left/
right) for the first and second row;
• automatic system called three-
zonewith additional rear fans which
can be controlled by the second row
passengers to change the second and
third row vent air capacity.
IMPORTANTManual selections
prevail over automatic selections and
are stored in the memory until the
user activates the system automatic
mode (AUTO). Manual settings are
stored when the engine is turned off
and restored when the engine is start-
ed again.
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 68
Page 76 of 254
GETTING TO KNOW YOUR CAR
75
• “completely cold” setting: this
option can be selected automatically
by pressing and keeping button A(–)
or E(–) pressed until 14°C are
reached; in this case the system per-
formance is at the highest. With this
option the system works in mono
conditions and the following settings
are active:
– slider turned to “completely cold”;
– air distribution during ventilation;
– maximum air capacity value;
– compressor on;
– automatic recirculation off, even if
it is possible to activate it manually
without leaving the wished setting.• “completely hot” setting: this
option can be selected automatically
by pressing and keeping button A(+)
or E(+) pressed until 28°C are
reached; in this case the system per-
formance is at the highest. The fol-
lowing settings are active as well:
– slider turned to “completely hot”;
– air directed to windscreen/feet or
feet, according to the outside tem-
perature;
– maximum air capacity value;
– compressor controlled by the sys-
tem;
– automatic recirculation closed even
if it possible to activate manually the
open recirculation without leaving the
required setting.• fan speed setting: this is possi-
ble by turning slider L; the wished
speed value is displayed through the
front fan stake blackening C.
IMPORTANTWhen the engine is
started with the climate control sys-
tem in automatic mode (AUTO) and
the external temperature is very low,
the fan may not be activated. Do not
consider it a malfunction; the system
will restore the normal operation as
soon as the temperature threshold set
by the system is reached.
• air distribution selection: this is
possible by pressing altogether H, I,
Mon the central rotating slider L.
Air can be distributed in five
ways: ventilation (front), bilevel
(front/feet), feet, windscreen/feet,
windscreen (MAX-DEF).
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 75
Page 77 of 254
GETTING TO KNOW YOUR CAR
76
To select the wished air distribution
press the related button and turn off
other possible selections. The con-
nected led switching on and off con-
firm the selection.
When the automatic mode (AUTO)
is on, air distribution is controlled by
the system, thus the related leds are
all turned off.
• compressor on/off: if the com-
pressor is turned off by pressing but-
ton Nwhen the led is lit, the related
led will go off; if the same button is
pressed when the led is switched off,
the system will control the compres-
sor (on/off).
If the system is working in automat-
ic mode the compressor is controlled
by the system according to the outside
temperature.
When the compressor is turned off
with the related led off, air recircula-
tion keeps the conditions prior to
switching off (closed or open) and it is
still possible to activate the open re-
circulation. Even with recirculation
closed, there is still a given quantity
of not treated air depending on the fan
setting and the vehicle speed, so thatwindow misting is prevented in nor-
mal conditions (spring-summer).
• automatic mode (AUTO) set-
ting: this is possible by pressing but-
ton Band the system will be con-
trolled automatically. AUTO and sym-
bol ò(ice) are displayed. It means that
the system will control temperature,
air distribution and the main fan speed.
If button Nis pressed when the sys-
tem is in automatic mode, the com-
pressor and switchover to cold air are
deactivated, the related led and sym-
bol ò(ice) go off and the system
keeps working in automatic mode.
• MAX-DEF on: this is possible by
pressing button Gand window
demisting will be quickly reached.To exit this function press button G
again or one of the following buttons:
A, B, D, E, H, I, M, O.
• rear heated window on: this is
possible by pressing button F, and the
related led comes on. In this way the
rear window electrical resistances are
activated to heat and demist the rear
window. To stop it, press the button
again and the related led will go off.
Anyway, the rear heated window
works for a limited time and turns off
automatically.
Be careful not to dam-
age the rear heated win-
dow resistances when
cleaning it from inside.
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 76
Page 78 of 254
GETTING TO KNOW YOUR CAR
77
• recirculation on: when button O
is pressed it is possible to select the
following travelling conditions: closed
recirculation (relative led on), air com-
ing from outside (led off) recirculation
open, or having the system automatic
control on (led off even if activated).You are recommended
to use the inside air recir-
culation function in the
traffic jam (car lines inside or out-
side galleries) to prevent outside
polluted air from getting into the
vehicle. Anyway, do not use this
function when several people are
onboard, to prevent inside win-
dow misting.
• driver’s and passenger’s side
temperature alignment (MONO)
fig. 88 (for versions without ad-
ditional fans): this is possible by
pressing button D, so a single tem-
perature is reached inside the passen-
ger compartment.
• rear seat air capacity adjust-
ment (REAR) fig. 89 (for versions
without additional fans): this is pos-
sible by pressing button D, thus the
second row passengers can adjust air
capacity with the additional fan knobs
A-fig. 90. The rear fan symbol will be
viewed on the display C.The additional fan effect depends on
the position of knobs A:
0= additional fan with minimum ca-
pacity;
–= additional fan air capacity equal to
50% of the main fan current capacity;
AUTO = additional fan capacity
equal to the main fan capacity;
+= additional fan air capacity equal to
70% of the main fan current capacity.
It is easier to reach the
wished air temperature
conditions with inside air
recirculation. Anyway, it is better
not to use this function in
rainy/cold days because inside
window misting may increase, es-
pecially if the compressor is off.
fig. 90
F0B0102b
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 77
Page 79 of 254
GETTING TO KNOW YOUR CAR
78
TURNING THE SYSTEM OFF
The system can be switched off by
turning knurled knob Lanticlockwise
until the car shape is displayed with-
out the fan symbol.
When the system is turned off it
makes the following operations:
– storing of conditions prior to
switching off;
– the graphics on display Cgo off ex-
cept for the car shape;
– the air recirculation is taken to
open position (outside air intake);
– the compressor is excluded;
– the fan is excluded;
– the air is distributed to the wind-
screen;
– the air mixing is in “completely
cold” position.FAILURE INDICATION
If any failures are detected (locked
switches, sensor malfunction, electri-
cal failures, etc.) the system automat-
ically sets the “recovery” mode, which
is displayed by the flashing points sep-
arating the temperature decimals on
the display C. In this case contact a Fi-
at Dealership as soon as possible.
Recovery mode
The system will work in the follow-
ing way:
– driver’s and passenger’s tem-
peratures: aligned and evolving in the
same way;
if buttons Aor Eare locked tem-
perature is set at 21°C by the system;
– main fan, distribution, com-
pressor, recirculation: they work in
automatic mode (AUTO);
– AUTO function:main fan, air dis-
tribution, compressor and air recircu-
lation are automatically controlled by
the system and the impulses on the
relative switches have no effect;– MAX-DEF function: the system
directs air to the windscreen and the
air distribution, compressor, AUTO
and air recirculation switches are not
active, while the main fan and tem-
perature functions are still active;
– REAR function: additional fans
cannot be switched on;
– rear window: cannot be switched
on.
INDEPENDENT ADDITIONAL
HEATER
To improve your comfort, cars with
JTD engines, can be fitted with an in-
dependent additional heater.
After switching the engine off or with
engine idling, the additional heater
could stay on hissing and exhaling
smoke and smell.
078-135 ULYSSE ING 10-03-2009 11:39 Pagina 78
Page 129 of 254
GETTING TO KNOW YOUR CAR
128
All control, repair and replacement
operations concerning the air bags
must only be carried out c/o Fiat
Dealership.
If the car is to be demolished, Fiat
Dealershipshould be contacted to
have the system deactivated.
If the vehicle changes ownership, the
new owner must be informed of the
method of use of air bags and the
above warnings and also be given this
“Owner handbook”.
IMPORTANTThe triggering of
pretensioners, front air bags and side
air bags is decided in a differentiated
manner by the electronic control unit,
depending on the type of crash. The
failure to deploy one or more of them
does not mean that the system is not
working properly.GENERAL NOTES
If the
¬warning light
does not turn on when
turning the ignition key to
M or if it stays on when travelling,
this could indicate a failure in
safety retaining systems; under
this condition air bags or preten-
sioners could not trigger in the
event of collision or, in a re-
stricted number of cases, they
could trigger accidentally. Stop
the car and contact Fiat Dealer-
ship to have the system checked
immediately.
When the ignition key is
turned to M, the warning
light
“(with the passen-
ger’s front air bag deactivation
switch in the ON position) turns
on for about 4 seconds and flash-
es for another 4 seconds to remind
that the passenger’s air bag and
side air bags will be deployed in a
crash, after which it should go off.
IMPORTANTTriggering of the air
bags releases a small amount of pow-
der. This powder is not harmful and
does not indicate the start of fire; al-
so the surface of the deployed bag and
the vehicle interior may be covered by
dusty residue: this may irritate the skin
and eyes. In the event of exposure,
wash with neutral soap and water.
The airbag system has a validity of 14
years for the pyrotechnic charge and
10 years for the coil contact . As this
date approaches, contact a Fiat Deal-
ership.
WARNINGSShould an accident
occur in which the Airbag is activated,
take the vehicle to a Fiat Dealership
to have the safety device, the elec-
tronic control unit, the seat belt, the
pretensioners and the electric system
checked.
078-135 ULYSSE ING 10-03-2009 11:39 Pagina 128
Page 153 of 254
DRIVING YOUR CAR
152
USEFUL
ACCESSORIES
fig. 1
In addition to the legal requirements
we recommend keeping the following
in the car:
– first-aid kit with non-alcoholic base
disinfectant, sterile gauze, a roll of
gauze bandage, plasters, etc.;
– electric torch;
– round-nosed scissors;
– work gloves;
– fire extinguisher.
These articles are all available from
Lineaccessori Fiat range.
fig. 1
F0B0202b
– check the air cleaner and have it re-
placed, if needed;
– check the tyre pressure and pos-
sible damages, cuts or cracks on their
surfaces. If present, have them re-
placed;
– check the engine belt conditions;
– connect the battery negative (–)
terminal after checking the battery
charge.
136-152 ULYSSE ING 10-03-2009 11:40 Pagina 152
Page 185 of 254
CAR MAINTENANCE
184
C C
A A
R R
M M
A A
I I
N N
T T
E E
N N
A A
N N
C C
E E
SCHEDULED
SERVICING
Correct maintenance of the car is es-
sential for ensuring it stays in tip-top
condition for a long time to come.
This is why Fiat has programmed a
number of service operations every
30,000 km.
Remember, however, that Scheduled
Servicing is not enough. Even before
30,000 km are reached, and also in be-
tween service coupons, you should
still check the level of the various liq-
uids and tyre pressure regularly.IMPORTANTThe Manufacturer
requires the Service Schedule coupons-
related checks to be carried out. Fail-
ure to do so could result in the war-
ranty being cancelled for those defects
that can be attributed to such failure.
Scheduled Servicing is performed at
a Fiat Dealershipand there is a set
time scale for such operations.
If it is seen that further replacements
or repairs are necessary in addition to
the work being carried out, these will
only be done after the customer has
his/her consent.IMPORTANTYou are recom-
mended to get in touch with a Fiat
Dealershipimmediately if any small
running problems crop up without
waiting for the next coupon.
If the vehicle is fre-
quently used to tow trail-
ers, carry out the sched-
uled service operations more fre-
quently than shown.
184-213 ULYSSE ING:184-213 ULYSSE ING 13-11-2009 10:13 Pagina 184