brake FORD AEROSTAR 1997 1.G Owners Manual

5
%*
[II05200(ALL)03/96]
Special Notice
[II05250(ALL)03/96]
NOTICE TO OWNERS OF
E-4WD VEHICLES
[II05300(ALL)03/96]
As with other vehicles of this type, failure to
operate this vehicle correctly may result in loss
of control or an accident. Be sure to read the
special driving instructions in the section
Electronic 4-Wheel Drive (E-4WD)in this book.
%*
[II05545(ALL)01/96]
Federal Highway Administration
Regulation
*
[II05560(ALL)01/96]
Regulations such as those issued by the Federal
Highway Administration or issued pursuant to
the Occupational Safety and Health Act (OSHA),
and/or state and local laws and regulations may
require additional equipment for the way you
intend to use the vehicle. It is the responsibility
of the registered owner to determine the
applicability of such laws and regulations to
your intended use for the vehicle, and to
arrange for the installation of required
equipment. Your Ford dealer has information
about the availability of many items of
equipment which may be ordered for your
vehicle.
%
*
[II06000(ALL)01/96]
Breaking Your Vehicle In
*
[II06100(ALL)01/96]
Your new vehicle goes through an adjustment or
break-in period during the first 1,000 miles
(1,600 km) that you drive it. During the break-in
period, you need to pay careful attention to how
you drive your vehicle.
%*
[II06300(ALL)01/96]
q
Avoid sudden stops.Because your vehicle
has new brake linings, you should take these
steps:
*
[II06400(ALL)01/96]
Ð Watch traffic carefully so that you can
anticipate when to stop.
File:02cpiia.ex
Update:Fri Jun 7 14:22:57 1996

6
*
[II06500(ALL)01/96]
Ð Begin braking well in advance.
*
[II06600(ALL)01/96]
Ð Apply the brakes gradually.
*
[II06700(ALL)01/96]
The break-in period for new brake linings
lasts for 100 miles (160 km) of city driving or
1,000 miles (1,600 km) of highway driving.
*
[II06750(ALL)05/96]
q
Wheel lug nuts must be retightened to proper
torque specifications at 500 miles/800 km of
new vehicle operation. Proper torque
specifications are provided in theRoadside
Emergencieschapter. Also retighten to proper
torque specifications at 500 miles/800 km
after any wheel change or any other time the
wheel lug nuts have been loosened.
%*
[II06800(ALL)03/96]
q
Use only the type of engine oil that Ford
recommends.SeeEngine oil recommendations
in the Index. Do not use special ªbreak-inº
oils.
*
[II10000(ALL)03/96]
Things to Know About Using
This Guide
*
[II10100(ALL)03/96]
Congratulations on the purchase of your new
vehicle. This guide has information about the
equipment and the options for your new vehicle.
You may not have bought all of the options
available to you. If you do not know which
information applies to your vehicle, talk to your
dealer.
*
[II10200(ALL)03/96]
This guide describes equipment and gives
specifications for equipment that was in effect
when this guide was approved for printing. Ford
may discontinue models or change specifications
or design without any notice and without
incurring obligation.
File:02cpiia.ex
Update:Fri Jun 7 14:22:57 1996

9
%*
[IS03000(ALL)01/96]
The Mechanical Cluster
*
[IS03100(ALL)01/96]
The following warning lights and gauges are on
the mechanical cluster. All of the warning lights
and gauges alert you to possible problems with
your vehicle. Some of the lights listed are
optional. The following sections detail what each
of these indicators means.
%*
[IS03200(ALL)01/96]
Brake System Warning Light
*
[IS03300(ALL)03/96]
The warning light for the brakes can show two
things Ð that the parking brake is not fully
released, or that the brake fluid level is low in
the master cylinder reservoir. If the fluid level is
low, the brake system should be checked by
your dealer or a qualified service technician.
*
[IS03400(ALL)03/96]
This light illuminates when you turn the ignition
key to START to verify that the indicator bulb is
working. If the light stays on or illuminates after
you have released the parking brake fully, have
the hydraulic brake system serviced.
*
[IS03500(ALL)03/96]
RWARNING
The BRAKE light indicates that the brakes
may not be working properly. Have the
brakes checked immediately.
[IS03600(ALL)01/96]
one inch art:0095034-A
Brake warning light symbol
File:03cpisa.ex
Update:Fri Jun 7 14:23:36 1996

10 [IS03700(ALL)01/96]Rear Anti-Lock (ABS) Brake Warning Light
[IS03900(ALL)03/96]
To check the rear ABS brake warning light, turn
the ignition key to the ON position. The rear
ABS brake warning light should glow
momentarily.
*
[IS03950(ALL)03/96]
NOTE: If it does not glow momentarily, have
your vehicle's electrical system checked
immediately.
[IS03975(ALL)01/96]
NOTE: If the rear ABS brake warning light
begins to flash in a repeating flash
sequence, check the rear anti-lock
brake system continuous power fuse
and brake lights for proper operation.
[IS04000(ALL)01/96]
one inch art:0095035-A
Rear anti-lock warning light symbol
*
[IS04100(ALL)03/96]
RWARNING
If the anti-lock brake system warning
light remains on or comes on while
driving, have the braking system checked
by a qualified service technician as soon
as possible.
*
[IS04110(ALL)03/96]
NOTE: If a fault occurs in the anti-lock
system, and the brake warning light is
not lit, the anti-lock system is disabled
but normal brake function remains
operational.
File:03cpisa.ex
Update:Fri Jun 7 14:23:36 1996

18
*
[IS11501(ALL)03/96]
If your engine overheats:
*
[IS11601(ALL)03/96]
1. Pull off the road as soon as it is safely
possible.
*
[IS11701(ALL)01/96]
2. Turn off the engine.
*
[IS11801(ALL)03/96]
3. Let the engine cool.DO NOT REMOVE
COOLANT SYSTEM FILL CAP UNTIL
THE ENGINE IS COOL.
*
[IS11901(ALL)01/96]
4. Check the coolant level following the
instructions on checking and adding coolant
to your engine. Refer toEngine coolantin the
Index. If you do not follow these
instructions, you or others could be injured.
[IS12325(ALL)01/96]
quarter page art:0020541-B
Engine coolant temperature gauge
%*
[IS12601(ALL)03/96]
Speedometer
*
[IS12700(ALL)03/96]
The speedometer tells you how many miles
(kilometers) per hour your vehicle is moving.
*
[IS12750(ALL)03/96]
Your vehicle contains a speedometer which
receives its input from the Anti-Lock brake
sensor. The speedometer is also used to provide
a speed signal for correct operation of the
vehicle's Powertrain Control Module (PCM),
electronic transmission, and speed control (if so
equipped). Because of this, it is very
IMPORTANT to change the speedometer's
internal conversion constant if the size of the
tires on the vehicle is changed. Changing the
conversion constant to the proper value when
File:03cpisa.ex
Update:Fri Jun 7 14:23:36 1996

72 %
*
[CF01060(ALL)03/96]
Daytime Running Light System
*
[CF01070(ALL)03/96]
(Canadian vehicles only)
*
[CF01080(ALL)03/96]
The Daytime Running Light (DRL) system turns
the high beam headlamps on, with a reduced
light output, when:
*
[CF01090(ALL)03/96]
q
The headlamp system is in the OFF position,
and
*
[CF01100(ALL)01/96]
q
The vehicle is running, and
*
[CF01110(ALL)03/96]
q
The vehicle has a fully released parking
brake.
*
[CF01120(ALL)01/96]
NOTE: You may notice that the lights flicker
when the vehicle is turned on or off.
This is a normal condition.
*
[CF01130(ALL)03/96]
RWARNING
The Daytime Running Light (DRL) system
will not illuminate the tail lamps and
parking lamps. Turn on your headlamps
at dusk. Failure to do so may result in a
collision.
*
[CF01140(ALL)01/96]
Instrument Panel Illumination
*
[CF01190(ALL)03/96]
The instrument panel lights can be turned on by
pulling the headlamp switch toward you to
either the first or outer position. You can
brighten or dim the instrument panel lights by
rotating the headlamp switch knob.
% [CF01230(ALL)04/96]
High-mount Brakelamp
[CF01235(ALL)01/96]
The high-mount brakelamp is located above the
rear window on liftgate models, and on the roof
above the rear doors on dual rear door models.
File:05cpcfa.ex
Update:Mon Jun 24 08:10:35 1996

73 [CF01240(ALL)05/96]
two third page art:0021014-B
High-mount brakelamp
%*
[CF01250(ALL)01/96]
Illuminated Entry System (If equipped)
[CF01260(ALL)01/96]
If your vehicle is equipped with this option, the
interior courtesy lamps and dome lamp will
light when either outside front door handle is
raised. They will turn off automatically after
approximately 25 seconds or when the ignition
key is turned to ON or ACC.
*
[CF01320(ALL)01/96]
Radio
*
[CF01330(ALL)01/96]
For information about the radio in your vehicle,
refer to theElectronic Sound Systemschapter in
this Owner Guide.
File:05cpcfa.ex
Update:Mon Jun 24 08:10:35 1996

74
*
[CF01340(ALL)01/96]
Clock Controls on Electronic
Radios
[CF01345(ALL)04/96]
The electronic radios have a built-in clock. For
complete operating instructions, refer to the
Electronic Sound Systemschapter in this Owner
Guide.
*
[CF02100(ALL)01/96]
Ignition
%*
[CF02110(ALL)01/96]
Understanding the Positions of the Ignition
*
[CF02120(ALL)01/96]
quarter page art:0020004-B
The positions of the key in the ignition lock cylinder.
%*
[CF02130(ALL)04/96]
ACCESSORY allows some of your vehicle's
electrical accessories such as the radio and the
windshield wipers to operate while the engine is
not running.
*
[CF02135(ALL)01/96]
LOCK locks the steering wheel and gearshift
lever.
*
[CF02140(ALL)01/96]
LOCK is the only position that allows you to
remove the key. The LOCK feature helps to
protect your vehicle from theft.
*
[CF02150(ALL)01/96]
If your key is stuck in the LOCK position and
will not turn, move your steering wheel left or
right until the key turns freely.
*
[CF02160(ALL)01/96]
OFF allows you to shut off the engine and all
accessories without locking the steering wheel or
the automatic transmission gearshift lever.
*
[CF02170(ALL)01/96]
ON allows you to test your vehicle's warning
lights (except the brake system warning light) to
File:05cpcfa.ex
Update:Mon Jun 24 08:10:35 1996

75
make sure they work before you start the
engine. The key returns to the ON position once
the engine is started and remains in this position
while the engine runs.
*
[CF02180(ALL)01/96]
START cranks the engine. Release the key once
the engine starts so that you do not damage the
starter. The key should return to ON when you
release it. The START position also allows you
to test the brake warning light.
%
*
[CF02500(ALL)02/96]
The Turn Signal Lever
*
[CF02510(ALL)02/96]
You can use the turn signal lever on the left side
of the steering column to:
*
[CF02520(ALL)02/96]
q
operate the turn signals and cornering lamps
*
[CF02530(ALL)03/96]
q
turn the high beams on/off
*
[CF02540(ALL)03/96]
q
flash the lamps
*
[CF02550(ALL)03/96]
q
turn the windshield wipers and washer
on/off
%*
[CF02560(ALL)01/96]
Turn Signals
[CF02570(ALL)01/96]
one third page art:0095013-A
Turn signal operation
*
[CF02580(ALL)08/95]
If the turn indicator light in the instrument
panel does not illuminate or remains on (doesn't
flash) when you signal a turn, the turn signaling
system is malfunctioning. Have this condition
File:05cpcfa.ex
Update:Mon Jun 24 08:10:35 1996

81
you may want to shift to the next lower gear to
reduce your vehicle's speed.
[CF08450(ALL)03/96]
If your vehicle slows down more than 10 mph
(16 km/h) below your set speed on an uphill,
your speed control will disengage. Pressing
RESUME will re-engage it.
*
[CF08700(ALL)05/96]
RWARNING
Do not use the speed control in heavy
traffic or on roads that are winding,
slippery, or unpaved.
*
[CF08800(ALL)05/96]
To Set a Higher Set Speed
[CF08900(ALL)03/96]
Press and hold SET ACCEL. Release the switch
when the desired vehicle speed is reached.
[CF08950(ALL)03/96]
OR
[CF08970(ALL)03/96]
Press and release SET ACCEL. Each press will
increase the set speed by 1 mph (1.6 km/h).
[CF08975(ALL)03/96]
OR
*
[CF09000(ALL)05/96]
You may accelerate with the accelerator pedal at
any time during speed control usage. Releasing
the accelerator pedal will return your vehicle
speed to the previously programmed set speed.
*
[CF09100(ALL)05/96]
To Set a Lower Set Speed
[CF09200(ALL)03/96]
Press and hold COAST. Release the switch when
the desired speed is reached.
[CF09220(ALL)03/96]
OR
[CF09260(ALL)03/96]
Press and release COAST. Each press will
decrease the set speed by 1 mph (1.6 km/h).
[CF09280(ALL)03/96]
OR
[CF09300(ALL)03/96]
Depress the brake pedal. When the desired
vehicle speed is reached, press SET ACCEL.
File:05cpcfa.ex
Update:Mon Jun 24 08:10:35 1996