check engine FORD AEROSTAR 1997 1.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1997, Model line: AEROSTAR, Model: FORD AEROSTAR 1997 1.GPages: 347, PDF Size: 1.79 MB
Page 15 of 347
12 %
*
[IS04500(ALL)03/96]
Check Engine Warning Light
[IS04560(ALL)05/96]
This light illuminates when the engine's
Emission Control System requires service. It will
also illuminate when the ignition key is in the
ON position and the engine is off.
*
[IS05300(ALL)04/96]
one inch art:0020048-A
Check engine warning light
[IS05525(ALL)01/96]
Electronic 4-Wheel Drive Warning Light
(If equipped)
[IS05550(ALL)03/96]
The Electronic 4-Wheel Drive Warning Light
illuminates when the Electronic 4-Wheel Drive
system is not working properly. This light
illuminates briefly when you turn the ignition
key to the ON position, but should turn off
when the engine starts. If the light does not
illuminate when you turn the ignition to the ON
position, or if it illuminates and stays on when
you are driving, have your vehicle serviced as
soon as possible.
[IS05560(ALL)03/96]
The 4WD light will go off after a few seconds
and stay off if all systems are operating
correctly. If a problem is detected, the 4WD
warning light will flash a certain number of
times indicating the location of the problem. The
flashing will continue until the problem is
corrected. Each time the ignition key is turned
on, the controller will detect the problem and
flash the signal. The 4WD system remains safe to
operate and the vehicle should be returned for
service.
File:03cpisa.ex
Update:Fri Jun 7 14:23:36 1996
Page 16 of 347
13 [IS05575(ALL)01/96]
one inch art:0020529-B
Electronic 4-wheel drive warning light
%*
[IS05900(ALL)01/96]
Charging System Light
*
[IS06000(ALL)05/96]
This light indicates that your battery is not being
charged and that you need to have the electrical
system checked.
[IS06050(ALL)01/96]
one inch art:0095040-A
Charging system light
*
[IS06100(ALL)03/96]
This light illuminates every time you turn the
ignition to the ON or START position (engine
off). The light should go off when the engine
starts and the alternator begins to charge.
*
[IS06300(ALL)03/96]
If the light stays on or illuminates when the
engine is running, have the electrical system
checked as soon as possible.
%*
[IS06305(ALL)05/96]
Supplemental Air Bag Readiness Light and
Tone Generator
*
[IS06310(ALL)05/96]
This light illuminates for six seconds when the
ignition is turned to the ON position. If the light
fails to illuminate, continues to flash, remains on,
or if a series of five beeps is heard, have the
system serviced as soon as possible.
File:03cpisa.ex
Update:Fri Jun 7 14:23:36 1996
Page 18 of 347
15 %
*
[IS06400(ALL)05/96]
Battery Voltage Gauge (Voltmeter)
*
[IS06601(ALL)04/96]
This gauge shows you the battery voltage when
the ignition key is in the ON position.
*
[IS06700(ALL)01/96]
If you are running electrical accessories (when
the engine is off, or idling at a low speed), the
pointer may move toward the lower end of the
normal band. If it stays outside the normal band
area, have your vehicle's electrical system
checked as soon as it is safely possible.
*
[IS06701(ALL)04/96]
If the battery is operating under cold weather
conditions, the pointer may indicate in the upper
range of the NORMAL band while the battery is
charging. If you are running electrical accessories
with the engine off or idling at a low speed, or
the battery is not fully charged, the pointer may
move toward the lower end of the NORMAL
band.
*
[IS06750(ALL)04/96]
If it stays outside the NORMAL band, have your
vehicle's electrical system checked as soon as it
is safely possible.
*
[IS06900(ALL)03/96]
quarter page art:0020052-D
Battery voltage gauge
File:03cpisa.ex
Update:Fri Jun 7 14:23:36 1996
Page 19 of 347
16 %
*
[IS07500(ALL)04/96]
Engine Oil Pressure Gauge
*
[IS07601(ALL)01/96]
This gauge indicates the engine's oil pressure,
not the oil level. However, if your engine's oil
level is low, it could affect the oil pressure. With
the engine running, the pointer should move
into the NORMAL band. If the pointer drops
below the NORMAL band while the engine is
running, you have lost oil pressure and
continued operation will cause severe engine
damage.
*
[IS07701(ALL)05/96]
If you lose engine oil pressure:
*
[IS07801(ALL)04/96]
1. Pull off the road as soon as safely possible.
*
[IS07901(ALL)04/96]
2. Shut off the engine immediately or severe
engine damage could result.
*
[IS08001(ALL)01/96]
3. Check the engine's oil level, following the
instructions on checking and adding engine
oil. Refer toEngine oilin the Index. If you
do not follow these instructions, you or
others could be injured. To assure an
accurate reading, your vehicle should be on
level ground.
*
[IS08051(ALL)01/96]
4. If the level is low, add only as much oil as
necessary before you start the engine again.
Do not overfill. Do not operate the engine if
the pointer is below the NORMAL band,
regardless of the oil level. Contact your
nearest dealer for further service actions.
*
[IS08200(ALL)03/96]
quarter page art:0020057-D
Engine oil pressure gauge
File:03cpisa.ex
Update:Fri Jun 7 14:23:36 1996
Page 21 of 347
18
*
[IS11501(ALL)03/96]
If your engine overheats:
*
[IS11601(ALL)03/96]
1. Pull off the road as soon as it is safely
possible.
*
[IS11701(ALL)01/96]
2. Turn off the engine.
*
[IS11801(ALL)03/96]
3. Let the engine cool.DO NOT REMOVE
COOLANT SYSTEM FILL CAP UNTIL
THE ENGINE IS COOL.
*
[IS11901(ALL)01/96]
4. Check the coolant level following the
instructions on checking and adding coolant
to your engine. Refer toEngine coolantin the
Index. If you do not follow these
instructions, you or others could be injured.
[IS12325(ALL)01/96]
quarter page art:0020541-B
Engine coolant temperature gauge
%*
[IS12601(ALL)03/96]
Speedometer
*
[IS12700(ALL)03/96]
The speedometer tells you how many miles
(kilometers) per hour your vehicle is moving.
*
[IS12750(ALL)03/96]
Your vehicle contains a speedometer which
receives its input from the Anti-Lock brake
sensor. The speedometer is also used to provide
a speed signal for correct operation of the
vehicle's Powertrain Control Module (PCM),
electronic transmission, and speed control (if so
equipped). Because of this, it is very
IMPORTANT to change the speedometer's
internal conversion constant if the size of the
tires on the vehicle is changed. Changing the
conversion constant to the proper value when
File:03cpisa.ex
Update:Fri Jun 7 14:23:36 1996
Page 156 of 347
155
*
[TO06575(ALL)01/96]
Whenever you start your vehicle, release the key
as soon as the engine starts. Excessive cranking
could damage the starter.
*
[TO06601(ALL)01/96]
After starting, allow the engine to idle for a few
seconds before driving away.
%*
[TO06625(ALL)05/96]
NOTE: Your vehicle is equipped with a
brake-shift interlock feature. This
feature prevents you from shifting
from P (Park) unless you have the
brake pedal depressed. (The ignition
must be in the ON position.) If you
cannot shift from P (Park) with the
brake pedal depressed:
*
[TO06627(ALL)05/96]
1. Apply the parking brake.
*
[TO06629(ALL)05/96]
2. Remove the key.
*
[TO06631(ALL)05/96]
3. Insert the key and rotate it one position
clockwise (ignition in the OFF position).
*
[TO06633(ALL)05/96]
4. Apply the brake pedal and shift to N
(Neutral). (If the vehicle is shifted back to P
[Park], you must repeat the previous steps.)
*
[TO06635(ALL)05/96]
5. Start the vehicle.
*
[TO06637(ALL)05/96]
If you need to shift out of P (Park) by using the
alternate procedure described above, it is
possible that a fuse has blown and that your
brakelamps may also not be functional. Please
refer to the chapter titledRoadside Emergenciesin
this Owner Guide for instructions on checking
and replacing fuses.
*
[TO06640(ALL)05/96]
RWARNING
DO NOT DRIVE YOUR VEHICLE UNTIL
YOU VERIFY THAT THE BRAKELAMPS
ARE WORKING.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996
Page 157 of 347
156
*
[TO06800(ALL)01/96]
If the engine still does not start after two
attempts:
*
[TO06825(ALL)01/96]
1. Turn the ignition key to the OFF position.
*
[TO06851(ALL)01/96]
2. Press the accelerator all the way to the floor
and hold it.
*
[TO06876(ALL)01/96]
3. Turn the ignition key to the START position.
*
[TO06900(ALL)01/96]
4. Release the ignition key when the engine
starts.
*
[TO06925(ALL)03/96]
5. Release the accelerator gradually as the
engine speeds up.
*
[TO06951(ALL)05/96]
If the engine still does not start, the fuel pump
shut-off switch may have been activated. For
directions on how to reset the switch seeFuel
Pump Shut-Off Switchin the index.
%*
[TO07300(ALL)01/96]
A computer system controls the engine's idle
speed. When you start your vehicle, the engine's
idle speed normally runs high. These faster
engine speeds will make your vehicle coast
slightly faster than its normal idle speed. It
should, however, slow down after a short time.
If it does not, have the idle speed checked.
*
[TO07390(ALL)01/96]
If the engine idle speed does not slow down
automatically, do not allow your vehicle to idle
for more than 10 minutes. Have the vehicle
checked.
*
[TO07400(ALL)01/96]
RWARNING
Extended idling at high engine speeds can
produce very high temperatures in the
engine and exhaust system, creating the
risk of fire or other damage.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996
Page 160 of 347
159
*
[TO08560(ALL)03/96]
If your engine cranks but does not start after a
collision or substantial jolt:
*
[TO08570(ALL)01/96]
1. Turn the ignition key to the OFF position.
*
[TO08580(ALL)03/96]
2. Check under the vehicle for leaking fuel.
*
[TO08590(ALL)01/96]
3. If you do not see or smell fuel, push the red
reset button down. If the button is already
set, you may have a different mechanical
problem.
*
[TO08600(ALL)01/96]
4. Turn the ignition key to the ON position for
a few seconds, then turn it to the OFF
position.
*
[TO08610(ALL)03/96]
5. Check under the vehicle again for leaking
fuel.If you see or smell fuel, do not start
your vehicle again.If you do not see or
smell fuel, you can try to start your vehicle
again.
*
[TO08620(ALL)01/96]
6. Check all vehicle warning lights before
driving the vehicle.
[TO08630(ALL)04/96]
quarter page art:0020107-A
Reset button for fuel pump shut-off switch
*
[TO09200(ALL)02/96]
RWARNING
Do not start your vehicle in a closed
garage or in other enclosed areas. Exhaust
fumes can be toxic. Always open the
garage door before you start the engine.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996
Page 161 of 347
160
*
[TO09300(ALL)12/95]
Guarding Against Exhaust Fumes
*
[TO09400(ALL)01/96]
Carbon monoxide, although colorless and
odorless, is present in exhaust fumes. Take
precautions to avoid its dangerous effects.
*
[TO09600(ALL)01/96]
RWARNING
If you smell exhaust fumes inside your
vehicle, have your dealer inspect your
vehicle immediately. Do not drive if you
smell exhaust fumes.
[TO09700(ALL)04/96]
If your vehicle has rear windows and doors that
were installed as part of a van conversion, close
them while it is running. This prevents exhaust
fumes from being drawn into the passenger
compartment.
*
[TO09900(ALL)01/96]
Have the exhaust and body ventilation systems
checked whenever:
*
[TO10000(ALL)01/96]
q
your vehicle is raised for service
*
[TO10100(ALL)01/96]
q
the sound of the exhaust system changes
*
[TO10200(ALL)01/96]
q
your vehicle has been damaged in a collision
*
[TO10300(ALL)01/96]
Improve your ventilation by keeping all air inlet
vents clear of snow, leaves, and other debris.
*
[TO10400(ALL)01/96]
If the engine is idling while you are stopped in
an open area for long periods of time, open the
windows at least one inch (2.5 cm). Also, adjust
the heating or air conditioning system to bring
in outside air.
*
[TO10600(ALL)01/96]
q
HEATING Ð Set fan speed at MEDIUM or
HIGH, the function selector knob on VENT,
FLOOR, MIX, or the DEFROST symbol and
the temperature control knob on any desired
position.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996
Page 165 of 347
165
*
[GF01150(ALL)01/96]
If during normal operation the brake pedal
seems ªlowº, it may indicate the need for a
brake system inspection and/or service. You
should have your brakes checked as soon as
possible.
%*
[GF01200(ALL)01/96]
Occasional brake squeal during light to moderate
stops does not affect the function of the brake
system and is normal. However, if the squeal
becomes louder or more frequent, have your
brakes inspected by your dealer or a qualified
service technician.
*
[GF01250(ALL)03/96]
RWARNING
Modifications to the suspension spring
rates and/or vehicle ride height may
adversely affect vehicle stopping ability.
*
[GF01300(ALL)03/96]
If Brakes Pull
*
[GF01350(ALL)03/96]
q
Check tire pressure.
*
[GF01400(ALL)03/96]
q
Perform the self-adjustment procedure
described underIf Brakes Do Not Grip Well or
Pedal is ªLow.º
*
[GF01450(ALL)03/96]
If pull occurs during the first 500 miles
(800 km), make 10 moderately fast stops from
40 mph (65 km/h) and then perform the
self-adjustment procedure above. It may be
necessary to repeat this operation to properly
seat new brake linings and pads.
%*
[GF01500(ALL)01/96]
Stopping Distances
*
[GF01550(ALL)01/96]
Stopping distances vary with different loads and
driving conditions. Use caution when
encountering new conditions and acquaint
yourself with vehicle performance. Take full
advantage of engine braking power when
slowing down.
File:09cpgfa.ex
Update:Wed Jun 5 12:04:06 1996