length FORD AEROSTAR 1997 1.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1997, Model line: AEROSTAR, Model: FORD AEROSTAR 1997 1.GPages: 347, PDF Size: 1.79 MB
Page 59 of 347
56
*
[AS07850(ALL)06/95]
Using headphones with the rear seat
controls
[AS07855(ALL)03/96]
Two 3.5 mm headphone jacks have been
provided on the rear seat controls. Plug
headphone(s) into the provided jack(s) to
operate.
*
[AS07860(ALL)04/96]
Common Radio Reception
Conditions
*
[AS07865(ALL)05/96]
Several conditions prevent FM reception from
being completely clear and noise-free, such as
the following:
*
[AS07870(ALL)05/96]
1. Distance/Strength
*
[AS07875(ALL)05/96]
The strength of the FM signal is directly related
to the distance the signal must travel. The
listenable range of an average FM signal is
approximately 25 miles (40 kilometers). Beyond
this distance, the radio is operating in a fringe
area and the signal becomes weaker.
*
[AS07880(ALL)08/95]
NOTE: Always make sure your antenna
(whether you have a power antenna or
a manually adjustable antenna) is fully
extended to its maximum length for
proper reception. If your antenna is not
fully extended, you may experience
signal loss while traveling in fringe
reception areas.
*
[AS07885(ALL)05/96]
2. Terrain
*
[AS07890(ALL)05/96]
The terrain (hilly, mountainous, tall buildings) of
the area over which the signal travels may
prevent the FM signal from being noise-free.
*
[AS07895(ALL)05/96]
If there is a building or large structure between
the antenna and station, some of the signal
ªbendsº around the building, but certain spots
receive almost no signal. Moving out of the
File:04cpasa.ex
Update:Fri Jun 7 14:24:14 1996
Page 119 of 347
117
*
[SS07500(ALL)01/96]
Pull the belt across your hips andinsert the
tongue into the correct buckleon your seat
until you hear a snap and feel it lock. Make sure
the buckle is securely fastened.
%*
[SS07700(ALL)01/96]
If you need to lengthen the belt, unfasten it and
tip the belt tongue at a right angle to the belt.
Pull the belt tongue over your lap until it
reaches the buckle.
*
[SS07800(ALL)01/96]
If you need to shorten the belt, pull on the loose
end of the webbing until the belt fits snugly.
[SS08600(ALL)05/96]
To unfasten the belt, push the release button on
the buckle. This allows the tongue to unlatch
from the buckle.
*
[SS08800(ALL)05/96]
RWARNING
The lap belts should fit snugly and as low
as possible around the hips, not around
the waist.
%*
[SS09600(ALL)02/96]
Safety Belt Extension Assembly
*
[SS09700(ALL)01/96]
For some people, the safety belt may be too
short even when it is fully extended. You can
add about eight inches (20 cm) to the belt length
with a safety belt extension assembly (part
number 611C22). Safety belt extensions are
available at no cost from your dealer.
*
[SS09750(ALL)01/96]
Use only extensions manufactured by the same
supplier as the safety belt. Manufacturer
identification is located at the end of the
webbing on the label. Also, use the safety belt
extension only if the safety belt is too short for
you when fully extended. Do not use extension
to change the fit of the shoulder belt across the
torso.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996
Page 127 of 347
125
*
[SS11650(ALL)05/96]
NOTE: For additional important safety
information on the proper use of seat
belts, child seats, and infant seats,
please read the entire Safety Restraints
chapter in this owner guide.
%*
[SS11700(ALL)05/96]
How Does the Air Bag Supplemental
Restraint System Work?
*
[SS11800(ALL)05/96]
The Air Bag Supplemental Restraint System is
designed to activate when the vehicle sustains
sufficient longitudinal (lengthwise) deceleration
that is equal to or greater than hitting an
immovable barrier head on at a range of about
8-14 mph (13-23 km/h). The fact that the air
bags did not inflate in a collision does not mean
that something is wrong with the system.
Rather, it means the forces were not of the type
sufficient to cause activation.
*
[SS11900(ALL)05/96]
If the vehicle is in a moderate or severe frontal
collision, the system is activated and the air bags
inflate rapidly. After the air bag inflates, it will
quickly deflate. After the air bag deployment,
you may notice a smoke-like, powdery residue
or smell the burnt propellant. This is normal.
The residue may consist of cornstarch or talcum
powder (which is used to lubricate the air bag)
or sodium compounds, such as sodium
carbonates (e.g. baking soda) that result from the
combustion process that inflates the air bag.
Small amounts of sodium hydroxide may be
present which may irritate the skin and eyes, but
none of the residue is toxic. The Air Bag
Supplemental Restraint System will reduce, but
not eliminate all injuries in an accident.
*
[SS12000(ALL)05/96]
RWARNING
Several air bag system components get hot
after inflation. Do not try to touch them
after inflation.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996
Page 140 of 347
138
[SS27300(ALL)01/96]
Installing Child Safety Seats at
the Rear Center Seating Position
with Locking Adjustable Lap Belt
[SS27350(ALL)01/96]
DO NOT install a forward-facing child safety
seat in the third row center seating position.
Forward-facing seats must be installed with a
lap/shoulder belt, or a lap belt and top tether
strap.
[SS27400(ALL)01/96]
1. Lengthen the lap belt. To lengthen the belt,
hold the tongue so that its bottom is
perpendicular to the direction of webbing
while sliding the tongue toward the loose
end of webbing.
*
[SS27450(ALL)01/96]
2. Place the child safety seat in the center
seating position.
*
[SS27500(ALL)01/96]
3. Route the tongue and webbing through the
child seat according to the child seat
manufacturer's instructions.
*
[SS27550(ALL)01/96]
4. Insert the belt tongue into the proper buckle
for the center seating position until you hear
a snap and feel it latch. Make sure the
tongue is securely fastened to the buckle by
pulling on tongue.
*
[SS27600(ALL)01/96]
5. Push down on the child seat while pulling
on the loose end of the lap belt webbing to
tighten the belt.
*
[SS27650(ALL)01/96]
6. Before placing the child into child seat,
forcibly tilt the child seat from side-to-side
and in forward directions to ensure that the
seat is held securely in place. If the child
seat moves excessively, repeat steps 5
through 6, or properly install the child seat
in a different seating position.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996
Page 181 of 347
181 [GF29250(ALL)01/96]
Standard length vehicles adapted for trailer tow
may require relocation of the underbody spare
tire. It is recommended that you secure the tire
under the rear-most seat using the hold-down
hardware located with the jack.
[GF29301(ALL)01/96]
one third page art:0020268-A
Spare tire stowage (standard length model)
*
[GF29350(ALL)01/96]
Do not tow a trailer until your vehicle has been
driven at least 500 miles (800 km).
%
*
[GF29401(ALL)01/96]
Vehicle Loading/Towing
Information
*
[GF29450(ALL)01/96]
Your vehicle's load capacity is designated by
weight, not volume, so you cannot necessarily
use all available space with large or heavy loads.
Maximum safe vehicle weights as well as tire,
rim sizes and inflation pressures are specified for
your vehicle at the assembly plant on the Safety
Compliance Certification Label. The Certification
Label is located on the left front door lock facing
or the door latch post pillar.
File:09cpgfa.ex
Update:Wed Jun 5 12:04:06 1996
Page 211 of 347
211
*
[ER04300(ALL)02/96]
When you drive with the temporary spare tire,
DO NOT:
*
[ER04400(ALL)02/96]
q
exceed 50 mph (80 km/h) under any
circumstances.
*
[ER04500(ALL)02/96]
q
load your vehicle so that it is heavier than
the maximum vehicle load rating listed on
the tire decal.
*
[ER04600(ALL)02/96]
q
tow a trailer.
*
[ER04700(ALL)02/96]
q
use tire chains on this tire.
*
[ER04800(ALL)02/96]
q
try to repair the temporary spare tire or
remove it from its wheel.
*
[ER04900(ALL)02/96]
q
use the wheel for any other type of vehicle.
*
[ER05000(ALL)02/96]
q
drive through an automatic car wash with
this tire. Because the temporary spare tire is
smaller than a conventional tire, it reduces
the ground clearance. Your vehicle may get
caught in the rails and it could be damaged.
%*
[ER05100(ALL)02/96]
Spare Tire Location
[ER05200(ALL)01/96]
If your vehicle is a standard length van model,
the spare tire is mounted inside a carrier at the
left rear quarter panel. To remove the spare tire,
remove the wing nut and plate. A flat tire can
be temporarily stowed in the same location.
[ER05300(ALL)01/96]
quarter page art:0020264-A
A side mounted spare tire
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996
Page 212 of 347
212 [ER05400(ALL)01/96]If your vehicle is the model with a standard
length body or extended length (all models), the
temporary spare tire is stowed at the rear of the
vehicle under the body.
[ER05450(ALL)01/96]
The standard length E-4WD model spare tire is
mounted on the floor.
[ER05500(ALL)01/96]
To remove underbody temporary spare tire:
[ER05600(ALL)01/96]
1. Insert lug nut wrench into the actuator hole
and turn counterclockwise until the cable
extends to allow the spare tire to be pulled
rearward from under the vehicle.
[ER05700(ALL)04/96]
2. Slide the spare tire to the rear and remove
the retainer from the wheel.
[ER05800(ALL)01/96]
3. To stow cable/retainer with spare tire
removed, insert cable fitting into carrier rear
wall slot, place wheel retainer against the
carrier, and turn lug nut wrench clockwise
until slack is removed.
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996
Page 214 of 347
214 [ER06300(ALL)01/96]3. Rotate wrench clockwise until tire is secured.
(Raising mechanism will slip.)
[ER06400(ALL)04/96]
4. Check for proper seating against underbody
supports and retighten if necessary.
[ER06500(ALL)01/96]
half page art:0020266-B
Spare tire Ð underbody carrier
[ER06600(ALL)01/96]
RWARNING
Do not stow any conventional spare tire
or flat temporary spare tire in the
underbody position. Doing so may cause
damage to the tire, rear axle, or brake
lines. (Standard length only)
[ER06800(ALL)01/96]
A flat tire can be temporarily secured to the
floor pan under the rear-most seat. To
temporarily secure a flat tire:
[ER06900(ALL)01/96]
1. Remove the spare tire ªJº bolt, plate and
wing nut from their stowed location on the
jack.
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996
Page 215 of 347
215 [ER07000(ALL)01/96]
2. Position the flat tire, valve stem up, under
the rear-most seat and over the ªJº bolt
attaching bracket on the floor pan.
[ER07100(ALL)01/96]
3. Insert the ªJº hook bolt through the center of
the wheel and hook on bracket.
[ER07200(ALL)01/96]
4. Install plate over ªJº hook bolt and secure
with wing nut.
[ER07300(ALL)01/96]
quarter page art:0020267-A
A Stowed position of ªJº bolt, plate and wing nut
(Standard length model)
[ER07400(ALL)01/96]
one third page art:0020268-A
Flat tire stowage (Standard length model)
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996
Page 217 of 347
217
*
[ER15420(ALL)03/96]
When one of the back wheels is off the ground,
the transmission alone will not prevent the
vehicle from moving or slipping off the jack,
even if the vehicle is in P (Park). To prevent the
vehicle from moving when you change a tire, be
sure the parking brake is set, then block the
wheel (both directions) that is diagonally
opposite (other side and end of the vehicle) to
the tire being changed.
*
[ER15430(ALL)03/96]
RWARNING
If the vehicle slips off the jack, you or
someone else could be seriously injured.
*
[ER15550(ALL)01/96]
2. Get out the spare tire and jack.
[ER15600(ALL)01/96]
The jack, jack handle and lug nut wrench are
stowed separately on the left hand wheelhouse
inner panel on standard length models. And in
the right rear storage compartment on extended
length models.
[ER15700(ALL)01/96]
one third page art:0020285-A
Jack stowage
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996