lock FORD ASPIRE 1997 1.G Service Manual

122
*
[ER02985(ALL)01/96]
If the Engine Cranks but Does
Not Start or Starting After a
Collision
*
[ER02990(ALL)02/96]
If the engine cranks but does not start or if you
have had a collision, the fuel pump shut-off
switch may have been triggered. The shut-off
switch is a device that stops the fuel pump
when your vehicle has been involved in a
substantial jolt.
*
[ER02995(ALL)03/96]
For information on how to check and reset the
fuel pump shut-off switch, seeFuel pump shut-off
switchin the Index.
%
*
[ER03000(ALL)01/96]
Fuses
[ER03005(ALL)01/96]
Fuses protect your vehicle's electrical system
from overloading. If electrical parts in your
vehicle are not working, the system may have
been overloaded and blown a fuse. Before you
replace or repair any electrical parts, check the
appropriate circuit protectors.
[ER03010(ALL)04/96]
The following charts tell you which fuses protect
each electrical part of your vehicle. If a fuse
blows, all the parts of your vehicle that use the
circuit will not work.
*
[ER03015(ALL)01/96]
Once you have determined which fuses to check,
follow the procedures underChecking and
replacing fuseslater in this chapter.
[ER03020(ALL)04/96]
Your vehicle has a main fuse block under the
hood and a regular fuse box mounted in the
instrument panel behind a cover.
File:10icerf.ex
Update:Tue Mar 4 08:55:59 1997

123 [ER03025(ALL)01/96]
Main fuse block
[ER03027(ALL)04/96]
NOTE: Ford recommends that the high
amperage fuses in the main fuse block
be replaced by a qualified technician.
[ER03030(ALL)01/96]
If the 80 Amp. fuse is blown, it must be
replaced. To remove the main fuse block and
replace the fuse:
[ER03035(ALL)01/96]
one third page art:0032220-B
Main fuse block location
[ER03040(ALL)01/96]
1. Disconnect the negative battery cable.
[ER03045(ALL)01/96]
2. Remove the nuts on either end.
[ER03050(ALL)01/96]
3. Lift the fuse block and open the flaps on the
side of the fuse block.
[ER03055(ALL)01/96]
4. Remove the bolts on either side of the block.
[ER03060(ALL)01/96]
5. Replace the fuse with a new one of the same
rating.
File:10icerf.ex
Update:Tue Mar 4 08:55:59 1997

124 [ER03065(ALL)01/96]
one third page art:0032234-BRemoving fuse block
[ER03070(ALL)01/96]
To install the fuse block:
[ER03075(ALL)01/96]
1. Place the fuse block cover back in position
and fasten the bolts on both sides.
[ER03080(ALL)01/96]
2. Attach the nuts on both ends of the fuse
block.
[ER03085(ALL)01/96]
3. Connect the negative battery cable.
[ER03090(ALL)01/96]
quarter page art:0032229-A
Main fuse block
File:10icerf.ex
Update:Tue Mar 4 08:55:59 1997

133 %
*
[ER07600(ALL)03/96]
Preparing to Change the Tire
*
[ER07700(ALL)01/96]
1. Make sure that your vehicle will not move
or roll. If you have an automatic transaxle,
put the gearshift in P (Park). If you have a
manual transaxle, put the gearshift in 1
(First). Set the parking brake and block the
wheel that is diagonally opposite the tire
that you are changing.
[ER08000(ALL)01/96]
half page art:0030148-A
Blocking the wheel diagonally opposite the tire being
changed
*
[ER08090(ALL)01/96]
When one of the front wheels is off the ground,
the transaxle alone will not prevent the vehicle
from moving or slipping off the jack, even if the
vehicle is in P (Park) or 1 (First). To prevent the
vehicle from moving when you change one of
the front tires, put a block behind the wheel that
is diagonally opposite to the tire.
File:10icerf.ex
Update:Tue Mar 4 08:55:59 1997

134
*
[ER08100(ALL)03/96]
WARNING
If the vehicle slips off the jack, you or
someone else could be seriously injured.
*
[ER08250(ALL)01/96]
2. Get out the spare tire and jack.
[ER08275(ALL)04/96]
Remove the wheel lug wrench from the tool
kit. To remove the spare tire, turn the
hold-down bolt counterclockwise with the
wheel lug wrench. To remove the jack, turn
the jack hold-down bolt counterclockwise.
Remove the tire retaining tool from the tool
kit.
[ER08350(ALL)01/96]
3. Remove the wheelcover with the tapered
end of a wheel nut wrench. Insert the handle
of the wrench and twist it against the inner
wheelcover flange. Remove any chrome nuts
or plastic caps covering the wheel lug bolts.
[ER08400(ALL)01/96]
4. Remove the top lug bolt and insert the tire
retaining tool in its place. This will hold the
tire in place when the other lug bolts are
removed.
File:10icerf.ex
Update:Tue Mar 4 08:55:59 1997

135 [ER08500(ALL)01/96]
half page art:0032243-A
Tire retaining tool
[ER08550(ALL)01/96]
NOTE: Be sure to thread the retaining tool
until no threads on the retaining tool
are visible.
[ER08600(ALL)01/96]
5. Loosen the wheel lug bolts by turning the
handle of the wrench one half turn
counterclockwise. Do not remove the wheel
lug bolts until you raise the tire off the
ground.
File:10icerf.ex
Update:Tue Mar 4 08:55:59 1997

136 %
*
[ER08650(ALL)01/96]
Removing and Replacing the Tire
[ER08700(ALL)04/96]
1. Find the jacking location near the door of
the tire that you are changing. Position the
jack and turn the handle of the jack
clockwise until the wheel is completely off
the ground.
*
[ER08800(ALL)01/96]
WARNING
To lessen the risk of personal injury, do
not put any part of your body under the
vehicle while changing a tire. Do not start
the engine when your vehicle is on the
jack. The jack is only meant for changing
the tire.
[ER09200(ALL)01/96]
one third page art:0032213-A
Jack mounting position
[ER09600(ALL)04/96]
2. Remove the wheel lug bolts by using the lug
wrench. Never loosen the hub nuts. See the
illustration following Step 1Preparing to
Change the Tireif you are not sure where to
find the wheel bolts.
[ER09700(ALL)01/96]
3. Replace the flat tire with the spare tire. Keep
the retaining tool in place.
File:10icerf.ex
Update:Tue Mar 4 08:55:59 1997

138 [ER10100(ALL)01/96]
WARNING
Installation of an English thread lug bolt
into a metric hub will not properly secure
the wheel to the hub. Damaged lug bolts
may result in wheel separation and
possible injury.
*
[ER10200(ALL)03/96]
6. Lower the vehicle by turning the jack handle
counterclockwise.
[ER10500(ALL)01/96]
7. Remove the jack and fully tighten the wheel
lug bolts in the order shown in the
illustration under Step 1.
[ER10700(ALL)01/96]
8. Put the tire, jack, retaining tool and wrench
away.
[ER10750(ALL)01/96]
9. Secure the conventional tire where the spare
was stored with the bolt provided.
*
[ER10850(ALL)03/96]
10. Unblock the wheels.
%
*
[ER12255(ALL)02/96]
Jump-Starting Your Vehicle
[ER12260(ALL)01/96]
Your vehicle's battery may become discharged
(ªdieº) if you leave the lights or any electrical
equipment on after you turn the engine off. If
this happens, you may be able to jump-start
from a booster battery to start your vehicle.
*
[ER12265(ALL)02/96]
WARNING
The gases around the battery can explode
if exposed to flames, sparks, or lit
cigarettes. An explosion could result in
injury or vehicle damage.
*
[ER12270(ALL)02/96]
WARNING
To protect yourself when charging a
battery, always shield your face and eyes.
Make sure that you can breathe fresh air.
File:10icerf.ex
Update:Tue Mar 4 08:55:59 1997

144 [ER12600(ALL)01/96]When calling for a tow truck, tell the operator
what kind of vehicle you have. A towing
manual is available from Ford Motor Company
for all authorized tow truck oerators. Have your
tow truck driver refer to this manual for the
proper hook-up and towing procedures for your
vehicle.
*
[ER13000(ALL)01/96]
Towing With the Back Wheels Off the
Ground
[ER13150(ALL)01/96]
If it is necessary to tow your vehicle from the
rear (with the rear wheels off the ground), a
dolly must be placed under the front tires to
prevent transaxle damage.
*
[ER13200(ALL)01/96]
Do not use your vehicle's steering column lock
to secure the wheels in a straight-ahead position.
Always use a steering wheel clamping device
designed for towing service.
*
[ER13250(ALL)01/96]
Refer toTowing behind another vehicle
Ðrecreational vehiclein the Index for information
on towing behind an RV.
File:10icerf.ex
Update:Tue Mar 4 08:55:59 1997

147
*
[MC02000(ALL)01/96]
q
Do not work on a vehicle in an enclosed
space with the engine running, unless you are
sure you have enough ventilation.
*
[MC02100(ALL)01/96]
q
Never get under a vehicle while it is
supported only by a jack. If you must work
under a vehicle, use safety stands.
*
[MC02200(ALL)01/96]
q
Keep all lit cigarettes and other smoking
materials away from the battery and all
fuel-related parts.
*
[MC02700(ALL)01/96]
Working with the engine off:
[MC02750(ALL)01/96]
1. Set the parking brake fully and make sure
the gearshift is securely latched in P (Park)
(automatic transaxle) or 1 (First) gear
(manual transaxle).
*
[MC02800(ALL)01/96]
2. Remove the key from the ignition after you
turn the engine off.
*
[MC02850(ALL)01/96]
3. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[MC02900(ALL)01/96]
Working with the engine on:
*
[MC03000(ALL)01/96]
1. Set the parking brake fully and make sure
the gearshift is securely latched in P (Park)
(automatic transaxle) or Neutral (manual
transaxle).
*
[MC03050(ALL)01/96]
2. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[MC03200(ALL)01/96]
WARNING
Do not start your engine with the air
cleaner removed and do not remove it
while the engine is running.
File:11icmcf.ex
Update:Tue Mar 4 08:57:16 1997