lock FORD B MAX 2013 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine Circuits protectedFuse ratingFuse
Heated windshieldDome lampInterior mirror
Stop lamps10 A2
Reversing lamp3 A3
Headlamp leveling7.5 A4
Not used-5
Rear window wiper15 A6
Washer pump15 A7
Not used-8
Passenger heated seat15 A9
Driver heated seat15 A10
Not used-11
Airbag module10 A12
Ignition
10 A13
Electric power assistedsteeringInstrument clusterPassive anti-theft systemAnti-lock brake system
Powertrain control module7.5 A14Fuel pumpTransmission selector lever
Audio system7.5 A15Instrument cluster
Heated windshield7.5 A16
Not used-17
Not used-18
Data link connector10 A19
Trailer module20 A20
Audio system15 A21
148B-MAX (CB2) Vehicles Built From: 25-06-2012, Vehicles Built Up To: 31-12-2013Fuses

Downloaded from www.Manualslib.com manuals search engine Circuits protectedFuse ratingFuse
Navigation
Instrument cluster7.5 A22
Multi functional display
7.5 A23ClockInternal scannerHeating ventsAir conditioning panel
SYNC module10 A24
Not used-25
Front wiper left-hand side30 A26
Front wiper right-hand side30 A27
Voltage quality module30 A28
Rear power point20 A29
Cigar lighter20 A30Auxiliary power point
Not used-31
Not used-32
Not used-33
Keyless entry20 A34
Keyless entry20 A35
Not used-36
Ignition switch15 A37
Not used-38
Not used-39
Not used-40
Not used-41
Rear view camera7.5 A42
Active city stop module10 A43
149B-MAX (CB2) Vehicles Built From: 25-06-2012, Vehicles Built Up To: 31-12-2013Fuses

Downloaded from www.Manualslib.com manuals search engine Note:You must reset the bounce-backfeature for the power windows. See PowerWindows (page 53).
Make sure that you dispose ofold batteries in anenvironmentally friendly way.
Seek advice from your local authorityabout recycling old batteries.
CHECKING THE WIPER
BLADES
Run the tip of your fingers over the edge ofthe blade to check for roughness.
Clean the wiper blades with washer fluidor water applied with a soft sponge orcloth.
CHANGING THE WIPER
BLADES
Windshield Wiper Blades
Note:The windshield wiper blades aredifferent in length. See TechnicalSpecifications (page 169). If you installwiper blades of the wrong length, the rainsensor may not work correctly.
Changing the Windshield Wiper Blades
1.Press the locking buttons together.
2.Rotate and remove the wiper blade.
3.Install in the reverse order.
Note:Make sure that the wiper blade locksinto place.
Rear Window Wiper Blade
1.Lift the wiper arm.
2.Position the wiper blade at right anglesto the wiper arm.
3.Disengage the wiper blade from thewiper arm.
4.Remove the wiper blade.
5.Install in the reverse order.
160B-MAX (CB2) Vehicles Built From: 25-06-2012, Vehicles Built Up To: 31-12-2013Maintenance

Downloaded from www.Manualslib.com manuals search engine Note:Make sure that the wiper blade locksinto place.
ADJUSTING THE HEADLAMPS
You can adjust the headlamp beams forwhen you drive on the right-hand side orleft-hand side of the road.
1.Remove the headlamps. SeeRemoving a Headlamp (page 161).
2.Remove the covers. See Changing aBulb (page 162).
3.Slide the control on each headlamp toadjust the headlamp beam.
Note:When you return to driving on theother side of the road, remember to changethe headlamp beams to the original setting.
REMOVING A HEADLAMP
1.Open the hood. See Opening andClosing the Hood (page 152).
2.Remove the screws and push pins.
3.Lift the outer side of the headlamp todisengage it from the lower fixing point.
4.Pull the headlamp as far as possibletoward the center of your vehicle andremove.
5.Disconnect the two electricalconnectors.
Note:When fitting the headlamp, makesure that you reconnect the electricalconnector correctly.
161B-MAX (CB2) Vehicles Built From: 25-06-2012, Vehicles Built Up To: 31-12-2013Maintenance

Downloaded from www.Manualslib.com manuals search engine Note:When fitting the headlamp, makesure that you fully engage the headlamp inthe lower fixing point.
CHANGING A BULB
WARNINGS
Switch the lamps and the ignition off.
Let the bulb cool down beforeremoving it.
Do not touch the glass of the bulb.
Note:Only fit bulbs of the correctspecification.
Note:The following instructions describehow to remove the bulbs. Fit replacementsin the reverse order unless otherwise stated.
Headlamp
Note:Remove the covers to gain access tothe bulbs.
Headlamp high beamA
Headlamp low beamB
Direction indicatorC
Direction Indicator
1.Remove the headlamp. SeeRemoving a Headlamp (page 161).
2.Turn the bulb holder counterclockwiseand remove it.
3.Gently press the bulb into the bulbholder, turn it counterclockwise andremove it.
Headlamp High Beam
1.Remove the headlamp. SeeRemoving a Headlamp (page 161).
162B-MAX (CB2) Vehicles Built From: 25-06-2012, Vehicles Built Up To: 31-12-2013Maintenance

Downloaded from www.Manualslib.com manuals search engine 2.Remove the cover.
3.Disconnect the electrical connector.
4.Release the clip and remove the bulb.
Note:Do not touch the glass of the bulb.
Headlamp Low Beam
1.Remove the headlamp. SeeRemoving a Headlamp (page 161).
2.Remove the cover.
3.Turn the bulb holder counterclockwiseand remove it.
4.Remove the bulb.
Note:Do not touch the glass of the bulb.
Side Lamp
1.Remove the headlamp. SeeRemoving a Headlamp (page 161).
2.Remove the cover.
3.Remove the bulb holder.
4.Remove the bulb.
Side Repeater
1.Carefully remove the side repeater.
163B-MAX (CB2) Vehicles Built From: 25-06-2012, Vehicles Built Up To: 31-12-2013Maintenance

Downloaded from www.Manualslib.com manuals search engine 2.Remove the bulb holder.
3.Remove the bulb.
Approach Lamp
Note:Position the mirror glass as far inwardas possible.
1.Insert a screwdriver into the gapbetween the mirror housing and themirror glass and release the metalretaining clip.
2.Remove the lamp.
3.Remove the bulb.
Front Fog Lamps
Note:You cannot separate the fog lampbulb from the bulb holder.
1.Disconnect the electrical connector.
2.Turn the bulb holder counterclockwiseand remove it.
164B-MAX (CB2) Vehicles Built From: 25-06-2012, Vehicles Built Up To: 31-12-2013Maintenance

Downloaded from www.Manualslib.com manuals search engine Rear Lamps
Direction Indicator, Tail and BrakeLamp
1.Remove the trim panel.
2.Disconnect the electrical connector.
3.Remove the wing nut.
4.Remove the lamp.
5.Remove the bulb holder.
6.Gently press the bulb into the bulbholder, turn it counterclockwise andremove it.
A.Tail and brake lamp
B.Direction indicator
Reversing Lamp and Fog Lamp
1.Open the liftgate.
2.Remove the trim panel.
165B-MAX (CB2) Vehicles Built From: 25-06-2012, Vehicles Built Up To: 31-12-2013Maintenance

Downloaded from www.Manualslib.com manuals search engine 3.Disconnect the electrical connector.
4.Turn the bulb holder counterclockwiseand remove it.
5.Gently press the bulb into the bulbholder, turn it counterclockwise andremove it.
Central High Mounted Brake Lamp
1.Open the liftgate.
2.Detach the clips.
3.Insert a suitable object into the holes.
4.Carefully pull the lamp toward thefront of the vehicle to release the springclips.
5.Remove the lamp.
166B-MAX (CB2) Vehicles Built From: 25-06-2012, Vehicles Built Up To: 31-12-2013Maintenance

Downloaded from www.Manualslib.com manuals search engine 6.Remove the bulb holder.
7.Remove the bulb.
Licence Plate Lamp
1.Carefully release the spring clip.
2.Remove the lamp.
3.Remove the bulb.
Interior Lamp
1.Carefully remove the lamp.
2.Turn the bulb holder counterclockwiseand remove it.
3.Remove the bulb.
Reading Lamps
1.Carefully remove the lamp.
2.Turn the bulb holder counterclockwiseand remove it.
3.Remove the bulb.
167B-MAX (CB2) Vehicles Built From: 25-06-2012, Vehicles Built Up To: 31-12-2013Maintenance