maintenance FORD BRONCO 1996 5.G Owners Manual

3
*
[IN01600( ALL)04/95]
Finding Information in This Guide
[IN01700( ALL)04/95]
After you have read this guide once, you will
probably return to it when you have a specific
question or need additional information. To help
you find specific information quickly, you can
use the table of contents or the index.
*
[IN01800(BEF )05/95]
TheQuick Indexat the end of the book
provides a page number following each item
which indicates where detailed information can
be found.
*
[IN02000( ALL)05/95]
This guide has atable of contentsat the
beginning of the book to show chapter titles.
*
[IN02100( ALL)04/95]
To use theIndex, turn to the back of the book
and search in the alphabetical listing for the
word that best describes the information you
need. If the word you chose is not listed, think
of other related words and look them up. We
have designed the Index so that you can find
information under a technical term.
%*
[IN02200( ALL)04/95]
Canadian Owners Ð French Version
*
[IN02300( ALL)05/95]
French Owner Guides can be obtained from your
dealer or by writing to Ford Motor Company of
Canada, Limited, Service Publications, P.O. Box
1580, Station B, Mississauga, Ontario L4Y 4G3.
*
[IN02400( ALL)04/95]
Your Maintenance Schedule and
Record Booklet
*
[IN02500( ALL)03/95]
TheMaintenance Schedule and Recordbooklet lists
the services that are most important for keeping
your vehicle in good condition. A record log is
also provided to help you keep track of all
services performed.
File:ltinb.ex
Update:Fri Jun 9 15:32:32 1995

25
%*
[SR09900(BEF )05/95]
Safety Belt Maintenance
[SR10000(BEF )02/95]
Check your safety belt system periodically to
make sure that it works properly and isn't
damaged. If the webbing shows any wear, nicks
or cuts, have it examined by a qualified
technician to determine if replacement is
necessary. Always have your safety belt system
checked after a collision by a qualified
technician.
*
[SR10200(BEF )05/95]
All safety belt assemblies, including retractors,
buckles, front seat belt buckle support assemblies
(slide bar) (if so equipped), child safety seat
tether bracket assemblies (if so equipped), and
attaching hardware, should be inspected after
any collision. Ford recommends that all safety
belt assemblies used in vehicles involved in a
collision be replaced. However, if the collision
was minor and a qualified technician finds that
the belts do not show damage and continue to
operate properly, they do not need to be
replaced. Safety belt assemblies not in use
during a collision should also be inspected and
replaced if either damage or improper operation
is noted.
%*
[SR10210(BEF )05/95]
Cleaning the Safety Belts
*
[SR10220(BEF )05/95]
Clean the safety belts with any mild soap
solution that is recommended for cleaning
upholstery or carpets. Do not bleach or dye the
belt webbing because this may weaken it.
*
[SR10300(BEF )04/95]
Air Bag Supplemental Restraint
System (SRS)
*
[SR10400(B )03/94]
Driver air bag
*
[SR10500(B F )03/95]
Your vehicle is equipped with a driver side air
bag supplemental restraint system located in the
steering wheel and identified by the letters
ªSRSº in the center of the wheel.
File:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995

28
*
[SR12050(B F )03/93]
half page art:0021011-A
The location of the air bag and warning label
*
[SR12200(BEF )05/95]
The air bag system uses a readiness light and a
tone to indicate the condition of the system. The
readiness light is in the instrument cluster. When
you turn the ignition to the ON position, this
light will illuminate for approximately six (6)
seconds and then turn off. This indicates that the
system is operating normally.NOTE:
Maintenance of the air bag system is not
required.
*
[SR12300(BEF )05/95]
A problem with the system is indicated by one
or more of the following: the readiness light will
either flash or stay lit, or it will not light, or a
group of five beeps will be heard.
*
[SR12360(BEF )04/95]
RWARNING
If any of these things happen, even
intermittently, have the air bag system
serviced at your Ford or Lincoln-Mercury
dealer immediately.
File:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995

200
*
[DR18320(B F )03/91]
To shift from 4x4 LOW RANGE to 4x4:
*
[DR18380(B F )06/94]
Stop the vehicle and place the automatic
transmission into NEUTRAL or depress the
clutch on vehicles with a manual transmission.
Push the LOW RANGE button on the instrument
panel to shift the transfer case from 4x4 LOW
RANGE to 4x4.
*
[DR19200(B F )01/89]
Driving Off Road with 4-Wheel
Drive
*
[DR19300(B F )11/89]
Most vehicles with four-wheel drive are
especially equipped for driving on sand, snow,
mud, or rough terrain and have operating
characteristics that are somewhat different from
conventional vehicles, both off and on the road.
The driving tips below will help you learn to
use four-wheel drive.
*
[DR19400(B F )10/94]
q
Do not use 4WD LOW on dry, hard-surfaced
roads.
*
[DR19600(B F )11/89]
q
Special maintenance procedures are necessary
after operating with drive components in
water.
*
[DR19700(B F )08/94]
q
Manual locking hubs must be in LOCK
position before shifting into four-wheel drive.
*
[DR19800(B F )11/89]
When using four-wheel drive, maintain steering
wheel control at all times, especially in rough
terrain. Since sudden changes in terrain can
result in abrupt steering wheel motion, make
sure you grip the steering wheel rim from the
outside. Do not grip the spokes.
*
[DR19900(B F )05/90]
Drive cautiously to avoid vehicle damage from
concealed objects such as rocks and stumps.
Know the terrain or examine maps of the area in
question before driving. Map out your route
beforehand. To maintain steering and braking
control of your vehicle, you must have all four
File:ltdrb.ex
Update:Fri Jun 9 15:26:57 1995

233
*
[DR38925( ALL)01/95]
Servicing your vehicle if you tow
*
[DR38950( ALL)08/93]
If you tow a trailer for a long distance, your
vehicle will need to be serviced more frequently
than usual. Refer to theMaintenance Schedule and
Recordbooklet for additional information.
*
[DR39000( ALL)01/93]
Trailer towing tips
*
[DR39100( ALL)11/89]
Before starting on a trip, practice turning,
stopping and backing in an area away from
heavy traffic. Get to know the ªfeelº of the
vehicle/trailer combination.
*
[DR39200( ALL)05/90]
Practice backing up. Back up very slowly, with
someone outside at the rear of your trailer to
guide you. Place your hand at the bottom of the
steering wheel and move it in the direction you
want the rear of the trailer to swing. Slight
movement of the steering wheel results in a
much larger movement of the rear of the trailer.
*
[DR39300( ALL)11/89]
Allow more room for stopping with a trailer
attached. Trailer brakes should be applied first,
whether manually or automatically controlled,
when approaching a stop.
*
[DR39400( ALL)11/89]
For a good handling truck-trailer combination,
the trailer tongue load should be approximately
10-15% of the loaded trailer weight.
*
[DR39500( ALL)05/95]
Make a thorough check of your equipment
before starting out on the road. After you have
traveled about 50 miles (80 km) stop in a
protected area and double-check your hitch and
electrical connections. Also check trailer wheel
lug nuts for tightness.
File:ltdrb.ex
Update:Fri Jun 9 15:26:57 1995

249
*
[RE22300(BEF )01/95]
7. Remove the jack and fully tighten the lug
nuts in the order shown in the following
illustration.
*
[RE22400(B )12/89]
quarter page art:0020312-B
Lug nut tightening sequence
*
[RE23400(BEF )05/95]
RWARNING
Use of wheels or lug nuts other than
original equipment could cause damage to
the wheel or mounting system and allow
the wheels to come off while the vehicle
is in motion.
*
[RE23500(BEF )01/95]
8. Replace any wheel covers, ornaments, or hub
caps that your vehicle has. Make sure that
they are screwed or snapped into place.
[RE23615(BEF )02/95]
9. Put the tire, jack, and wrench away. (Make
sure jack is securely fastened so it doesn't
rattle when you drive.) The carrier is
designed to hold the temporary spare which
comes with your vehicle. The stowage of a
full size tire in the spare tire carrier may
damage the tire or the vehicle. The flat full
size tire should be stowed securely in the
vehicle until it can be repaired.
*
[RE23700(BEF )01/95]
10. Unblock the wheels.
*
[RE23800(B )06/93]
Retighten the wheel lug nuts to the specified
torque at 500 miles (800 km) of new vehicle
operation and at intervals specified in the
Maintenance Schedule and Recordbooklet.
File:ltreb.ex
Update:Fri Jun 9 15:25:48 1995

256
*
[HS00245( ALL)06/94]
How to use Roadside Assistance
*
[HS00250( ALL)06/94]
Your Roadside Assistance identification card can
be found in the Owner Guide portfolio in your
glove compartment. Complete the card and place
it in your wallet for quick reference.
*
[HS00255( ALL)04/95]
To receive roadside assistance in the United
States call 1-800-241-FORD (in Canada call
1-800-665-2006).
*
[HS00260( ALL)04/95]
Should you need to arrange for roadside
assistance yourself, Ford Motor Company will
reimburse the reasonable cost. To obtain
information about reimbursement call
1-800-241-FORD (in Canada call 1-800-665-2006).
*
[HS00300( ALL)01/95]
If You Have a Service Problem
*
[HS00400( ALL)01/95]
Ford Motor Company has authorized Ford and
Lincoln-Mercury dealerships that can service
your vehicle for you. This chapter tells you how
to get service or maintenance for your vehicle.
%*
[HS00525( ALL)03/95]
Service/Maintenance Concerns (U.S. or
Canada)
*
[HS00600(BEF )04/95]
Ford recommends taking your vehicle to your
selling dealer who wants to ensure your
continued satisfaction. You may, however, take
your vehicle to any authorized Ford or
Lincoln-Mercury dealer. In most cases, your
dealer will be able to resolve your concern.
*
[HS00700( ALL)03/95]
If you are not satisfied with the service you
received from your dealership's service
department, talk to the service manager at the
dealership. If you still are not satisfied, talk to
the owner or general manager of the dealership.
In most cases, you will have your concern
resolved at this level.
File:lthsb.ex
Update:Fri Jun 9 15:25:09 1995

261
*
[HS05100( ALL)04/95]
What is the Review Process?
*
[HS05200( ALL)04/95]
Your application will be reviewed and if it is
determined to be eligible, you will receive an
acknowledgment indicating the file number
assigned to your application and the local Board
address. At the same time, your dealer and Ford
Motor Company representative are asked to
submit statements.
*
[HS05300( ALL)04/95]
To review your case properly, the Board needs
the following information:
*
[HS05400( ALL)04/95]
q
legible copies of all documents and
maintenance or repair orders that relate to
the case
*
[HS05500( ALL)04/95]
q
the year, make, model, and vehicle
identification number
*
[HS05600( ALL)04/95]
q
the date you bought your vehicle
*
[HS05700( ALL)04/95]
q
the date of repair and the mileage at the time
of repair
*
[HS05800( ALL)04/95]
q
the current mileage
*
[HS05900( ALL)04/95]
q
the name of the dealer who sold you the
vehicle or who serviced your vehicle
*
[HS06000( ALL)04/95]
q
a brief description of your unresolved
complaint
*
[HS06100( ALL)05/95]
q
a brief summary of actions that were taken
with the dealer and Ford Motor Company
*
[HS06200( ALL)05/95]
q
the names (if known) of all people you
contacted at the dealership
*
[HS06300( ALL)04/95]
q
a description of the action you want done to
resolve your concern.
*
[HS06305( ALL)04/95]
Should your application NOT qualify for review,
an explanation will be mailed to you.
File:lthsb.ex
Update:Fri Jun 9 15:25:09 1995

265 %
*
[HS08100( ALL)03/95]
Canadian Motor Vehicle Arbitration Plan
(CAMVAP)
*
[HS08200( ALL)03/95]
If a specific item of concern arises, where a
solution cannot be reached between a vehicle
owner, Ford of Canada, and/or one of its
dealers (that all parties can agree upon), the
owner may wish to use the services offered by
the Canadian Motor Vehicle Arbitration Plan
(CAMVAP).
*
[HS08300( ALL)05/95]
CAMVAP uses the services of Provincial
Administrators to assist consumers in scheduling
and preparing for their arbitration hearings.
However, before you can proceed with
CAMVAP you must follow your manufacturer's
dispute resolution process as outlined under
ªService/Maintenance Concerns (U.S. or
Canada)º earlier in this chapter.
*
[HS08400( ALL)05/95]
Consumers wishing to obtain further information
about the program can obtain an information
booklet from your dealer or contact the
Provincial Administrator, Canadian Motor
Vehicle Arbitration Plan, at the address or
telephone number shown below.
*
[HS08450( ALL)05/95]
O & P Services
595 Bay Street Ð Suite 300
Toronto, Ontario
M5G 2C2
Telephone 1 (800) 207-0685
File:lthsb.ex
Update:Fri Jun 9 15:25:09 1995

275
Servicing Your Bronco
%*
[SV00300( ALL)03/95]
Service Made Easy
*
[SV00400(BEF )01/95]
Ford has two goals for servicing your vehicle.
*
[SV00500(BEF )01/95]
1. When we can, we design parts that do not
need to be serviced.
*
[SV00600(BEF )01/95]
2. We want to make servicing your vehicle as
easy as possible. To help you:
*
[SV00700(BEF )01/95]
q
We highlight do-it-yourself items in yellow in
the engine compartment so that you can find
them easily.
*
[SV00800(BEF )01/95]
q
When possible, we design parts Ð such as
the headlamp bulbs Ð that can be replaced
without tools.
*
[SV00900(BEF )05/94]
q
We give you a Maintenance Schedule that
makes tracking routine service for your
vehicle easy. The maintenance schedule is
located in theMaintenance Schedule and Record
booklet.
*
[SV01000( ALL)01/95]
This chapter tells you about the basic parts that
you need to check and service regularly.
*
[SV01100( ALL)02/95]
If your vehicle needs professional servicing, your
dealership can provide the parts and service
required. Check yourWarranty Information Booklet
to find out which parts and services are covered.
Also see theCustomer Assistancechapter of this
Owner Guide.
File:ltsvb.ex
Update:Tue Jun 20 16:56:22 1995