Wiring FORD C MAX 2008 1.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 2008, Model line: C MAX, Model: FORD C MAX 2008 1.GPages: 278, PDF Size: 17.5 MB
Page 76 of 278
Downloaded from www.Manualslib.com manuals search engine CHANGING A BULB
WARNINGS
On vehicles fitted with Xenonheadlamps, have the headlampbulbs changed by an expert. Thereis a risk of injury due to high voltage.
During operation, the bulbs andtheir surroundings get hot.Switch off the lights and let the bulbscool down before replacing them.
Always switch off lights and ignitionbefore replacing any bulb.
Never touch the glass of the bulbs.Fit only bulbs having a UV filter.Always replace a faulty bulb with anew one of the same type. Afterreplacing a bulb, check that the lightsoperate correctly.
Headlamps, side lamps,direction indicators
Note:It is necessary to remove theheadlamp assembly to remove anyof the bulbs.
Removing the headlampassembly
Open the bonnet.
Remove the screw.
WARNING
When re-installing the lampassembly, make sure that thewiring connectors and retaining clipsare engaged properly.
Press down the retaining clips at therear of the lamp assembly using ascrewdriver and carefully pull out thelamp assembly.
74
LightingE78106 E78107
Page 77 of 278
Downloaded from www.Manualslib.com manuals search engine Disconnect the wiring connector.
Install in the reverse order.
Front direction indicators
PY21 watt spherical bulb, orange
•Turn the bulb holder anticlockwiseand pull out.
•Turn the bulb under slightpressure anticlockwise andremove it.
•Replace the bulb.
When installing, pay attention to theguide tabs.
Opening the headlampassembly (Type 1)
Note:When replacing the cover,ensure that no wires are trapped atthe seals and that the clips engagewith a distinct click.
Release the clips and remove thecover.
Opening the headlampassembly (Type 2)
Remove the rubber caps.
Headlamps – dipped beam(Type 1)
H7, 55 watt halogen bulb
75
LightingE78108 E78109 E91732
Page 78 of 278
Downloaded from www.Manualslib.com manuals search engine •Disconnect the wiring connector.
•Release the wire clip, swivel it tothe side and pull out the bulb.
Install in the reverse order.
Headlamps – dipped beam(Type 2)
H7, 55 watt halogen bulb
•Turn the bulb holder anticlockwiseand pull it out.
•Pull out the bulb and replace it.
Install in the reverse order.
Headlamps – main beam
H1, 55 watt halogen bulb
•Disconnect the wiring connector.
•Release the wire clip, swivel itdown and pull out the bulb.
Install in the reverse order.
Side lamps
5 watt wedge base bulb
76
LightingE78110 E91734 E78111
Page 81 of 278
Downloaded from www.Manualslib.com manuals search engine •Prise out the fog lamp bezel at itsbase, slide the bezel downwardsand remove it.
•Loosen the screws and pull outthe lamp assembly.
•Disconnect the wiring connector.
•Remove the bulb and replace it.
Install in the reverse order.
Vehicles with a body styling kit
Insert your fingers into the hole in thebezel above the fog lamp and pull offthe complete bezel.
Front fog lamps (Type 2)
H8, 35 watt halogen bulb
1.Prise out the fog lamp bezel at itsbase, slide the bezel downwardsand remove it.
2.Loosen the screws and pull outthe lamp assembly.
3.Disconnect the wiring connector.
4.Remove the bulb and replace it.
79
LightingE78120 E78121 12E91735 34E91736
Page 82 of 278
Downloaded from www.Manualslib.com manuals search engine Install in the reverse order.
Rear lamps
Open the tailgate.
Remove the pillar panel trim insidethe luggage compartment.
Remove the sidewall panel trim togain access to the second wing nut.
Remove the wingnuts. Make sure thewing nuts do not fall into the opening.
Pull off the rear lamp assembly outof the two plastic retainers on thebody panel.
Disconnect the wiring connector.
Loosen the screws and remove thecomplete bulb holder.
80
LightingE78122 E78123 E78124 E78125
Page 264 of 278
Downloaded from www.Manualslib.com manuals search engine ELECTROMAGNETIC
COMPATIBILITY
WARNINGS
Your vehicle has been testedand certified to Europeanlegislations relating toelectromagnetic compatibility(2004/104/EC). It is your responsibilityto ensure that any equipment youhave fitted complies with applicablelocal legislations. Have anyequipment fitted by properly trainedtechnicians.
WARNINGS
Radio frequency (RF) transmitterequipment (e.g. cellulartelephones, amateur radiotransmitters etc.) may only be fittedto your vehicle if they comply with theparameters shown in the table below.There are no special provisions orconditions for installations or use.
Do not mount any transceiver,microphones, speakers, or anyother item in the deployment path ofthe airbag system.
Do not fasten antenna cablesto original vehicle wiring, fuelpipes and brake pipes.
Keep antenna and powercables at least 100mm from anyelectronic modules and airbags.
262
AppendicesE8599867123845