clock FORD CONTOUR 1997 2.G Owners Manual

7
Instrumentation
%*
[IS00200(ALL)01/96]
The instrument panel (dashboard) on your vehicle is divided
into several different sections. The illustrations on the following
pages show the major parts of the instrument panel that are
described in this chapter. Some items shown may not be on all
vehicles.
%*
[IS00300(ALL)01/96]
The main controls for the climate control system, clock, and
radio are on the instrument panel.
%*
[IS00400(ALL)03/96]
NOTE: Any cleaner or polish that increases the gloss (shine)
of the upper part of the instrument panel should be
avoided. The dull finish in this area is to help protect
the driver from undesirable windshield reflection.
File:03cdiso.ex
Update:Thu Sep 12 10:58:17 1996

26
*
[AS02800(ALL)02/96]
n
Using the ªSCAN/TUNEº button to scan radio stations
*
[AS02900(ALL)02/96]
Pressing the ªSCAN/TUNEº button once enters the scan
mode (display will indicate ªSCNº). Pushing the top (
a)
half of the ªSEEKº button will begin the scan mode up the
frequency band, stopping on each listenable station for
approximately five seconds. Pushing the bottom (
b) half of
the ªSEEKº button will begin the scan mode down the
frequency band, again stopping on each listenable station for
approximately five seconds.
*
[AS03000(ALL)03/96]
To stop the scan mode on the presently sampled station,
press the ªSCAN/TUNEº button again.
*
[AS03200(ALL)02/96]
n
Setting the Station Memory Preset buttons
*
[AS03300(ALL)10/95]
Your radio is equipped with 6 station memory buttons.
These buttons can be used to select up to 6 preset AM
stations and 12 FM stations (6 in FM1 and 6 in FM2).
*
[AS03400(ALL)03/96]1.
Select a band, then select a frequency.
*
[AS03600(ALL)10/95]2.
Press one of the memory preset buttons and hold the button
until the sound returns. That station is now held in memory
on that button.
*
[AS03700(ALL)10/95]3.
Follow the two steps above for each station memory preset
button you want to set.
*
[AS03850(ALL)03/96]
NOTE: If the vehicle's battery is disconnected, the clock and
station memory preset buttons will need to be reset.
[AS04150(ALL)02/95]
n
Using the Automatic Memory Store feature
*
[AS04250(ALL)02/96]
With Auto Memory Store, you can continually set strong
stations into your memory buttons without losing your existing
memory presets, which is especially handy while traveling. Your
radio will automatically set your memory buttons to the strong
local stations so you don't have to continually manually tune to
existing stations.
File:04cdaso.ex
Update:Thu Sep 12 10:59:17 1996

40
*
[AS22800(ALL)04/96]
n
Using the ªSEEKº function
*
[AS22900(ALL)09/95]
This feature on your radio allows you to automatically select
listenable stations up or down the frequency band. Press the
right (
a) side of the ªSEEKº button to select the next
listenable station up the frequency band. Press the left (
b)
side of the button to select the next listenable station down
the frequency band. By holding the button down, listenable
stations can be passed over to reach the desired station.
*
[AS23160(ALL)02/96]
n
Using the ªSCANº function (Stereo Cassette Radio)
*
[AS23170(ALL)06/95]
Press the ªSCANº button to enter the scan mode. The radio
will begin scanning up the frequency band, stopping on each
listenable station for approximately a five-second sampling.
This continues until you press the ªSCANº button a second
time. The display flashes ªAMº or ªFM.º
*
[AS23200(ALL)02/96]
n
Setting the Station Memory Preset buttons
*
[AS23325(ALL)10/95]
Your radio is equipped with 6 station memory buttons.
These buttons can be used to select up to 6 preset AM
stations and 12 FM stations (6 in FM1 and 6 in FM2).
*
[AS23400(ALL)08/95]
Follow the easy steps below to set these buttons to the desired
frequencies:
*
[AS23525(ALL)03/96]1.
Select a band, then select a frequency.
*
[AS23700(ALL)10/95]2.
Press one of the memory preset buttons and hold the button
until the sound returns. That station is now held in memory
on that button.
*
[AS23800(ALL)10/95]3.
Follow the two steps above for each station memory preset
button you want to set.
*
[AS23900(ALL)03/96]
NOTE: If the vehicle's battery is disconnected, the clock and
station memory preset buttons will need to be reset.
File:04cdaso.ex
Update:Thu Sep 12 10:59:17 1996

52
%*
[CF05200(ALL)03/96]
NOTE: Never use sharp instruments or window cleaners with
abrasives to clean the inside of your rear window. If
you do, you may damage the heating elements that
are bonded to the inside of the rear window and
cause damage to the rear window defroster.
%*
[CF05300(ALL)03/96]
The Interior and Exterior Lights
%*
[CF05400(ALL)03/96]
Turning On the Exterior Lights
[CF05500(ALL)12/95]
To turn on your headlamps, parking lamps, and tail lamps, use
the knob that is on the instrument panel, to the left of the
steering wheel.
[CF05600(O )04/96]
10-1/2 pica art:0001178-E
The knob for the exterior lights
[CF05800(ALL)04/96]
To turn on the parking lamps, tail lamps, license plate lamps
and side marker lamps, turn the knob clockwise to the first
position.
[CF05900(ALL)04/96]
To turn on the headlamps, parking lamps, tail lamps, license
plate lamps and side marker lamps, turn the knob clockwise to
the second position.
File:05cdcfo.ex
Update:Fri Sep 13 08:48:17 1996

Controls and Features
55
%*
[CF08000(ALL)03/96]
Clock
[CF08100(O )12/95]
7-1/2 pica art:0001220-B
The digital clock
*
[CF08300(ALL)12/95]1.
To set the hour, press and hold the hour button. When the
desired hour appears, release the button.
*
[CF08400(ALL)12/95]2.
To set the minutes, press and hold the minute button. When
the desired minute appears, release the button.
[CF08500(ALL)12/95]3.
To switch between a 12-hour clock and a 24-hour clock,
press both the hour and minute buttons at the same time.
Reset the time as above.
%*
[CF08600(ALL)05/96]
Storage Compartments
[CF08700(ALL)12/95]
Your vehicle may have several storage compartments:
[CF08800(ALL)12/95]
n
a coin holder on the instrument panel
*
[CF09000(ALL)05/96]
The controls on the steering column and wheel are designed to
give you easy access to the controls while you are driving.
File:05cdcfo.ex
Update:Fri Sep 13 08:48:17 1996

164
*
[ER07100(ALL)03/96]
RWARNING
If the vehicle slips off the jack, you or someone else
could be seriously injured.
*
[ER07200(ALL)01/96]2.
Get out the spare tire and jack.
*
[ER07300(ALL)03/96]
RWARNING
To avoid injury, never run the engine with one wheel off
the ground, such as when changing a tire.
[ER07400(ALL)12/95]3.
Remove the wheel cover from the wheel with the tapered
end of the wheel lug wrench. Insert and twist the handle,
then pry against the inner wheel cover flange. For
information about removing optional wheel center ornaments
seeStyled Polycast Wheel Ornamentslater in this section.
[ER07500(ALL)12/95]4.
Loosen the wheel lug nuts by pulling up on the handle of
the wrench one-half turn counterclockwise. Do not remove
the wheel lug nuts until you raise the tire off the ground.
For information about removing anti-theft lug nuts, see
Anti-Theft Wheel Lug Nutslater in this section.
%*
[ER07600(ALL)01/96]
Removing and Replacing the Tire
[ER07700(ALL)12/95]1.
Place the scissors-type jack under the side of the vehicle and
adjust the jack height with the jack handle. The jack should
fit in the notch in the vertical rocker panel flange which is
nearest to the wheel to be changed. The front and rear
jacking notches on each side of the vehicle are marked by
arrows in the rocker panel.
[ER07800(O )02/96]
On sport models with ªskirts,º you must remove a portion
of the skirt before placing the jack under the vehicle.
Squeeze the removeable portion of the skirt and pull down.
A tether connects it to the rocker panel.
File:10cdero.ex
Update:Thu Sep 12 11:06:09 1996

166
[ER08100(ALL)12/95]
17-1/2 pica art:0000528-E
The notches for the jack
*
[ER08200(ALL)12/95]2.
Turn the jack handle clockwise until the wheel clears the
ground. Remove the wheel lug nuts.
*
[ER08300(ALL)03/96]3.
Replace the flat tire with the spare tire, making sure that the
air valve stem is facing outward.
*
[ER08400(ALL)03/96]4.
Reinstall the lug nuts, tightening until the wheel is snug
against the hub. The beveled edges on the lug nuts face
inward. Do not fully tighten the lug nuts until you lower the
vehicle. If you do, you could force the vehicle off the jack.
*
[ER08500(ALL)03/96]5.
Lower the vehicle by turning the jack handle
counterclockwise.
File:10cdero.ex
Update:Thu Sep 12 11:06:09 1996

168
%*
[ER09400(ALL)01/96]
Anti-Theft Wheel Lug Nuts (If equipped)
[ER09500(ALL)12/95]
If your vehicle has this option, one of the lug nuts on each
wheel locks and must be unlocked with a special key. If you
lose the key, send the registration card to the manufacturer (not
to the dealer) to get a replacement key.
[ER09600(ALL)12/95]
NOTE: If you lose your lug wrench/lug nut key assembly, see
your nearest Ford or Lincoln/Mercury dealer who has
access to a master set of keys.
*
[ER09700(ALL)12/95]
NOTE: DO NOT USE A POWER IMPACT WRENCH ON
THE LUG NUT KEY.
[ER09800(ALL)12/95]
10-1/2 pica
art:0000529-B
The anti-theft lug nut and key
*
[ER09900(ALL)12/95]
Removing the anti-theft lug nut
*
[ER10000(ALL)02/96]
Insert the key over the locking lug nut. Make sure that you
hold the key square to the lug nut. If you hold the key on an
angle, you may damage the key and the lug nut.
*
[ER10100(ALL)12/95]
Place the lug nut wrench over the lug nut key and apply
pressure on the key with the wrench. Turn the wrench in a
counterclockwise direction to remove the lug nut.
File:10cdero.ex
Update:Thu Sep 12 11:06:09 1996

Maintenance and Care
193
*
[MC10651(ALL)05/96]
If you must remove the coolant recovery cap, follow these steps
to avoid personal injury:
*
[MC10661(ALL)05/96]1.
Before you remove the cap, turn the engine off and let it
cool.
*
[MC10671(ALL)05/96]2.
When the engine is cool, wrap a thick cloth around the cap.
Slowly turn cap counterclockwise to the first stop.
*
[MC10681(ALL)05/96]3.
Step back while the pressure releases.
*
[MC10691(ALL)05/96]4.
When you are sure that all the pressure has been released,
use the cloth to press the cap down, turn it counterclockwise,
and remove it.
*
[MC10701(ALL)05/96]
Use Ford Premium Cooling System Fluid E2FZ-19549-AA (in
Canada, Motorcraft CXC-8-B) or an equivalent premium engine
coolant that meets Ford specification ESE-M97B44-A. Ford
Premium Engine Coolant is an optimized formula that will
protect all metals and rubber elastomers used in Ford cooling
systems for 4 years or 50,000 miles (80,000 km).
*
[MC10711(ALL)05/96]
Do not use alcohol or methanol antifreeze or any engine
coolants mixed with alcohol or methanol antifreeze. Do not use
supplemental coolant additives in your vehicle. These additives
may harm your engine cooling system. The use of an improper
coolant may void the warranty of your vehicle's engine cooling
system.
*
[MC10721(ALL)05/96]
Recycled engine coolant
*
[MC10731(ALL)05/96]
Ford Motor Company recommends that Ford and
Lincoln-Mercury dealers use recycled engine coolant produced
by Ford-approved processes. Not all coolant recycling processes
produce coolant which meets Ford specification ESE-M97B44-A,
and use of such coolant may harm engine and cooling system
components.
File:11cdmco.ex
Update:Thu Sep 12 11:08:18 1996

Maintenance and Care
209
*
[MC22900(ALL)01/96]
n
Tire chains may affect vehicle handling. Drive carefully and
avoid hard braking.
*
[MC23000(ALL)01/96]
n
Do not use chains on temporary spare tires. They may
damage the vehicle and the tire.
*
[MC23100(ALL)01/96]
n
Remove tire chains at the first opportunity after using them
on snow and ice. Do not use the chains on dry roads.
%*
[MC23200(ALL)01/96]
Filling the Fuel Tank
*
[MC23900(ALL)12/95]
The fuel door is outside the car on the passenger side near the
back. To fill the fuel tank:
*
[MC24000(ALL)03/96]1.
After opening the fuel filler door, remove the cap carefully
and slowly by turning it counterclockwise 1/2 to 3/4 turn. If
a hissing sound is heard, wait until it stops, then continue
turning until the cap is free.
*
[MC24100(ALL)01/96]
RWARNING
The fuel system may be under pressure. If the fuel cap is
venting vapor or if you hear a hissing sound, wait until
it stops before completely removing the cap.
*
[MC24200(ALL)01/96]2.
Put the nozzle all the way inside the fuel filler pipe before
pumping the fuel.
*
[MC24300(ALL)01/96]
NOTE: If you spill any fuel on the body of your vehicle,
clean it off immediately. The fuel may dull or soften
the paint if you do not wash it off.
File:11cdmco.ex
Update:Thu Sep 12 11:08:18 1996