lock FORD E SERIES 1997 4.G Owner's Guide

7. Lower the vehicle by turning the
jack handle counterclockwise.
8. Remove the jack and fully
tighten the lug nuts in the
following pattern:
5 lug wheel
8 lug wheel
Never use wheels or lug
nuts different than the
original equipment as this could
damage the wheel or mounting
system. This damage could allow
the wheels to come off while the
vehicle is being driven.
9. Replace any wheel covers,
ornaments or hub caps. make sure
they are screwed or snapped in
place.
10. Stow the jack, handle and lug
wrench.
11. Unblock the wheels.
Roadside emergencies
119

Working with the engine off
1. Set the parking brake fully and
ensure the gearshift is securely
latched in P (Park).
2. Turn off the engine and remove
the key.
3. Block the wheels to prevent the
vehicle from moving unexpectedly.
DPRN 21
com_working_on.01
Maintenance and care
126

Working with the engine on
1. Set the parking brake fully and
ensure the gearshift is securely
latched in P (Park).
2. Block the wheels to prevent
your vehicle from moving
unexpectedly.
Do not start your engine
with the air cleaner
removed and do not remove it
while the engine is running.
DPRN 21
eco_opening_hood
Maintenance and care
127

standards for disposing of these
types of fluids. Call your local
recycling center to find out more
about recycling automotive fluids.
Adding engine coolant
Never remove the pressure
cap while the engine is
running or hot.
1. Before you remove the cap, turn
the engine off and let it cool.
2. When the engine is cool, wrap a
thick cloth around the cap and
turn it slowly counterclockwise.
3. Step back while the pressure
releases.
4. When you are sure that all the
pressure has been released, use
the cloth to remove the cap.
5. Add engine coolant until the
level is between the MIN and MAX
lines on the engine coolant
recovery reservoir.
Follow the recommended service
interval for changing engine
coolant as outlined in theService
Guide.
Checking the cooling system
hoses
Inspect all engine and heater
system hoses and hose connections
for:
²deterioration
²leaks
MAX FILL
MIN FILL
eco_adding_coolant
eco_checking_hoses
Maintenance and care
138

4. The relearning process will
automatically complete as you
drive the vehicle.
²If you do not allow the engine to
relearn its idle, the idle quality
of your vehicle may be adversely
affected until the idle is
eventually relearned.
²If the battery has been
disconnected or a new battery
has been installed, the clock and
preset radio stations must be
reset once the battery is
reconnected.
²Always dispose of used
automotive batteries in a
responsible manner. Follow your
community's standards for
disposal. Call your local
recycling center to find out
more about recycling automotive
batteries.
Disconnecting dual batteries (if
equipped)
Gasoline engines
Disconnect:
eco_battery_disconnect
eco_battery_gas_disconnect
Maintenance and care
146

the ignition to the LOCK position.
Do not move the wipers manually
across the windshield as this may
cause damage to the wiper system.
Inspect the wiper arm pivots on a
regular basis to ensure the wiper
arms move freely. Lubricate the
pivot points as necessary.
Replacing wiper blades
If the wiper blades do not work
properly after cleaning,
replacement of the blade assembly
or the blade element may be
necessary.
To replace the wiper blades:
1. Pull the wiper arm away from
the windshield and lock it into the
service position.
2. Turn the blade at an angle from
the wiper arm. Depress the lock
tab to release the wiper blade and
pull the wiper blade down toward
the windshield to remove it from
the arm.
3. Attach the new wiper to the
wiper arm and press it into place
until a click is heard.
eco_replacing_wiper_blades
com_about_tire_grades.01
Maintenance and care
150

1. Open the hood.
2. Push each clip tab toward the
engine compartment and lift
upward to the stop position.
3. Remove the headlamp assembly.
4. Remove bulb retention ring by
turning it counterclockwise about
1/4 turn.
5. Pull bulb assembly out of
headlamp assembly.
6. Pull out bulb.
7. Replace bulb.
8. Reverse steps 1±3 to replace
headlamp assembly.
Bulb specifications
DescriptionNumber of
BulbsTrade Number
Front Lamps - Exterior
Headlamps (low series) 2 H6054
Headlamps (high series) 2 9007
Park lamp and turn signal 2 3157NAK
Rear Lamps - Exterior
Back-up lamps 2 3156K
License plate lamp 2 186
Stop/Tail/Side marker lamp 2 3357K
Turn lamp 2 3156K
High-mount brakelamp 2 912
eco_bulb_specifications
Maintenance and care
166

DescriptionNumber of
BulbsTrade Number
Interior Courtesy Lamps
Cargo lamp 1 211-2
Dome lamp (standard) 1 912
Instrument panel
illumination2 194
Map/reading lamp 2 211-2
Radio Illumination
1
Instrument Panel
Automatic transmission
gear selector1 194
Instrument Panel Controls
A/C control 1 161
Heater control 1 161
Instrument Cluster
Seat belt light 1 194
High beam indicator 1 194
Brake Warning 1 194
Turn signal indicator 1 194
Anti-lock brake system 1 194
Service engine soon 1 194
Air bag readniness 1 194
Door ajar 1 194
Oil pressure/engine
coolant1 194
1Replaceable at Ford authorized
radio service centers.
NA Ð Natural amber
K Ð Krypton filled bulb
com_cleaning_caring.01
Maintenance and care
167

high pressure fluid could
penetrate the sealed parts and
cause damage.
²Do not spray with cold water to
avoid cracking the engine block.
²Cover the highlighted areas to
prevent water damage when
cleaning the engine.
²Never wash or rinse the engine
while it is running; water in the
running engine may cause
internal damage.
Cleaning plastic exterior parts
Use a vinyl cleaner for routine
cleaning of plastic. Clean with a tar
remover if necessary. Do not clean
plastic parts with thinners,
solvents or petroleum-based
cleaners.
Cleaning the exterior lamps
Wash the exterior lamps with the
same detergent you used to wash
the exterior of your vehicle. Use
glass cleaner or tar remover if
necessary.
To avoid scratching the lamps, do
not use a dry paper towel,
chemical solvents or abrasive
cleaners to clean the lamps.
com_plastic_exterior.01
com_exterior_lamps.01
eco_wiper_cleaning
Maintenance and care
170

Item Ford part name Ford part
numberFord
specification
Engine coolant Ford Premium
Cooling System
FluidE2FZ-19549-AA ESE-M97B44-A
Engine oil
(gasoline)Motorcraft
5W-30 Super
Premium Motor
OilXO-5W30-QSP WSS-M2C153-F
with API
certification
mark
Engine oil
(diesel)Consult separate diesel engine owner's guide
supplement
Hinges, latches
and striker
platesMulti-Purpose
GreaseD7AZ-19584-AA
or
D0AZ-19584-AAESR-M1C159-A
and
ESB-M1C93-B
Lock cylinders Penetrating
LubricantE8AZ-19501-B Ð
Power steering
reservoirMotorcraft
MERCONT
Automatic
Transmission
FluidXT-2-QDX MERCON
Automatic
transmissionMotorcraft
MERCONT
Automatic
Transmission
FluidXT-2-QDX MERCON
Windshield
washer fluid
reservoirUltra-Clear
Windshield
Washer
ConcentrateC9AZ-19550-AC
or BCESR-M17P5-A
Disc brake
caliper railsSilicone Brake
Caliper and
Dielectric
compoundD7AZ-19A331-A
WA-10ESE-M1C171-A
Capacities and specifications
175