instrument panel FORD ESCAPE 2015 3.G Quick Reference Guide

Instrument Panel
SYNC
SYNC with MyFord Touch
Convenience
Comfort
Liftgate
Function
Essential Information
4 – 5
6 – 7
8 – 10 11
12 – 13
14 – 1516 – 17
18 – 19
3
Table of Contents
WARNING
Driving while distracted can result in loss of
vehicle control, crash and injury. We strongly
recommend that you use extreme caution
when using any device that may take your focus
off the road. Your primary responsibility is the
safe operation of your vehicle. We recommend
against the use of any hand-held device while
driving and encourage the use of voice-operated
systems when possible. Make sure you are aware
of all applicable local laws that may affect the
use of electronic devices while driving.
fordowner.com (U.S.)
Learn More About Your New Vehicle
Scan the country-appropriate QR code with
your smartphone (make sure you have a scanner
app installed) and you can access even more
information about your vehicle.
ford.ca (Canada)

Instrument Panel
1
3
2
4
5
6
7
4
9
8

11
Remote Entry Icons
• Press once to lock all doors.
Press again within three seconds to
confirm all doors are locked.
• Press
once to unlock the driver’s
door. Press again within three
seconds to unlock all doors.
• Press
to activate the panic
alarm. Press again or switch on the
ignition to deactivate.
• Press
twice within three
seconds to open the liftgate.
• Car finder: Press
twice within
three seconds to locate your
vehicle. The horn sounds and the
lamps flash.
Intelligent Access*
Note: Your
transmitter
must be within
3 feet (1 meter)
of the vehicle
for intelligent
access to
function
properly. To unlock and open the door, pull a
front exterior door handle. To lock
the doors, press and hold the
sensor button on the door handle.
To unlock and open the liftgate, press
the exterior liftgate release button
in the top of the pull cup handle.
The intelligent access transmitter also
contains a mechanical key blade that
you can use to unlock the driver door,
if necessary.
Remote Start*
Remote start allows you to start the
engine from outside your vehicle using
your transmitter. To start, press
and then press twice within three
seconds. Once inside, apply the brake
while pressing the ENGINE START
STOP button. Shift into drive (D)
and go. To switch off the engine from
outside the vehicle after using your
remote start, press
once.
Universal Garage Door Opener*
Your driver’s
side visor has a
built-in wireless
transmitter
that replaces
the common hand-held garage door
opener. This system can also be
programmed to security systems, entry gates and home or office
lighting. Refer to the Universal Garage
Door Opener chapter in your Owner’s
Manual for programming instructions
and additional information on how to
use this device.
Active Park Assist*
The active park
assist system
can detect
an available
parallel parking
space and
automatically
steer the vehicle
into that space
(hands-free). The system visually
and audibly provides you with
braking, accelerating and gearshifting
instructions to park the vehicle. To
initiate active park assist, press the
AUTO |P| button located on the
instrument panel. To stop the parking
procedure, grab the steering wheel or
press the control again. For complete
information, refer to the Parking Aids
chapter of your Owner’s Manual.
Note: The driver is always responsible
for controlling the vehicle, supervising
the system and intervening, if required.
*if equipped
Convenience

Manual Liftgate
To Open the Liftgate 1. Unlock all the vehicle doors.
2. Press the button located inside the liftgate pull-cup
handle to unlatch the liftgate.
3. Pull on the outside handle to raise the liftgate.
Power Liftgate*
Note: If the vehicle is running,the liftgate operates only
with the transmission in park (P).
Touch a button to open or close the liftgate:
Press
twice within three seconds on your remote entry
transmitter or the button on the instrument panel. A
tone sounds when the liftgate starts to move. You Can Also Open the
Liftgate from the Rear of
Your Vehicle
1. Make sure you unlock
your lifgate first and
then press the button
located in the top of the
liftgate pull-cup handle.
2. Allow the power system
to open the liftgate after
pressing the control.
3. To close, press and
release the control
pictured below.
When the liftgate begins to
move, a tone sounds. Setting the Liftgate
Open Height
Once you open the power
liftgate, you can move
it manually to a desired
height. If the previously
programmed liftgate height
is lower than the fully
opened position, you can
manually push it upward.
To Program a New Height
1. Open the liftgate.
2.
Manually move the
liftgate to your
desired height.
3. Press and hold the
control button on the
liftgate until you hear
a tone, indicating that
your programming of
the liftgate height
is successful.
The liftgate then opens
to its newly programmed
height when you use the
power feature to open it.
To change the
programmed height,
repeat the process above.
14*if equipped
Liftgate