ignition FORD EXPLORER 1997 2.G User Guide

change to ªSTART OIL LIFE AT
XXX%.º
3. Press the OIL CHANGE RESET
control until the displayed
percentage is the Personalized Oil
Reset Percentage you desire.
Check charging system
The electrical system is not
maintaining a proper voltage. Have
the electrical system checked as
soon as safely possible.
Check engine temp
The engine coolant is overheating.
Refer toEngine coolant
temperature gaugein the
Instrumentationchapter for more
information regarding the engine
coolant system.
Check exterior lamps
At least one brake lamp, rear side
marker or low beam headlamp is
burned out. To determine which
lamp is burned out:
1. Turn ignition switch to OFF to
reset M/C.
- +H
L
H
C
uno_check_charging_system uno_check_engine_temp
uno_check_exterior_lamps
Instrumentation
22

2. With the brake lamps, parking
lamps and headlamps off, turn the
ignition switch to ON or ACC.
3. After M/C briefly illuminates
(about two seconds), press the
brake pedal. If ªCHECK
EXTERIOR LAMPSº is displayed,
then a brake lamp is burned out. If
this message is not displayed,
proceed to the next step.
4. Turn the light switch to the
parking lamp positions. If ªCHECK
EXTERIOR LAMPSº is displayed,
then a rear side marker is burned
out. If this message is not
displayed, proceed to the next
step.
5. Turn the light switch to the
headlamp position. If ªCHECK
EXTERIOR LAMPSº is displayed,
then a low beam headlamp is
burned out.
If you use additional lights, such as
trailer lights, or replace bulbs with
equipment that is not equal to the
original Ford equipment, you may
0P RND21
UNLEADED
FUEL ONLY
RPM x 100012345
6H
C
F
E
RSM
SET
ACC
COAST OFF ONOFF
SRS
OFF
DIM
020
1030405060
70
80
90
110
120000000oooo
km/h10020406080100
120
140
160
180
Instrumentation
23

get a false warning or no warning
at all.
Door ajar
The ignition switch is in the On or
Start position and a door is open.
Low fuel level
The fuel level is low.
Low oil level
The oil level is low. Refer to
Checking and adding engine oil
in theMaintenance and
carechapter for more information.
Low washer fluid
The washer fluid reservoir is less
than one quarter full.
F
E
H
L
uno_door_ajar
uno_low_fuel uno_low_oil
uno_low_washer
Instrumentation
24

Instrument panel dimmer
control
To adjust the instrument panel
dimmer control:
²Rotate the control up to
brighten the instrument panel
lighting.
²Rotate the control down to dim
the instrument panel lighting.
Daytime running light (DRL)
system (if equipped)
The DRL system turns on the
highbeam headlamps, with a
reduced light output, when:
²the vehicle is running and the
ignition is in the On position
²the vehicle has a fully released
parking brake
²the headlamp system is in the
position
0P RND21RPM x 100012345
6H
C
F
E
RSM
SET
ACC
COAST OFF ONOFF
SRS
OFF
DIM
020
1030405060
70
80
90
110
120000000oooo
km/h10020406080100
120
140
160
180
uno_drl_lights
Controls and features
26

The EATC feature will maintain a
selected temperature and
automatically control airflow. You
may manually override the EATC
operation. The EATC will only
operate with the ignition in the On
position.
To maximize system efficiency:
²Do not put items under the
front seats that will interfere
with the air flow to the rear
seats.
²Keep the air intake vents clear
of any snow, ice or leaves.
Automatic operation
To turn on the EATC:
²Press AUTO or any the six
override controls.
²Select the desired temperature.
To turn off the EATC:
²Press the OFF control.
²When the system is off, the
display window will be blank.
When AUTO is selected, the
system will automatically
determine fan speed and airflow
location and under normal
conditions should need no
additional adjustment.
¡F
AUTO
uno_automatic_operation
uno_temperature_select
Controls and features
33

Rear window defroster
Press the defroster control to clear
the rear window of thin ice and
fog.
The ignition must be in the ON
position to operate the rear
window defroster.
The defroster turns off
automatically after 10 minutes or
when the ignition is turned to the
OFF position. To manually turn off
the defroster before ten minutes
have passed, push the control
again.
REAR WINDOW WIPER AND
WASHER (IF EQUIPPED)
Washer
Press for rear washer fluid
operation.
0P RND21RPM x 100012345
6H
C
RSM
SET
ACC
COAST OFF ONOFF
SBSHI LOOFF*A/C*MAX
A/C
REW
1FF
2SIDE 1-2
3
FM 1STVOL – PUSH ON
AM
FMBASS TREBBAL FADE
AUTO
SET CLKSEEKTUNE
DISCSSCAN4DOLBY SYSTEMEJTAPE CDCOMP5SHUFFLE
6
PUSH020
1030405060
70
80
90
110
120000000ooookm/h10020406080100
120
140
160
180FE
uno_rear_washer
uno_rear_wiper
Controls and features
37

FUEL PUMP SHUT-OFF SWITCH
For information on the fuel pump
shut-off switch, refer toFuel
pump shut-off switchin the
Roadside emergencieschapter.
POSITIONS OF THE IGNITION
1. ACCESSORY allows the
electrical accessories such as the
radio and wipers/washer to operate
while the engine is not running.
2. LOCK locks the steering wheel
and gearshift lever and allows key
removal.
3. OFF shuts off the ignition and
accessories and allows the
gearshift and steering wheel to
move.
4. ON tests the warning lights. The
key must remain here when the
engine is running.
1
23
4
5
uno_pst-ignition
Controls and features
39

5. START cranks the engine. The
key must return to ON when
running.
SPEED CONTROL
(IF EQUIPPED)
To turn speed control on
Press ON.
Vehicle speed cannot be controlled
until the vehicle is travelling at or
above 48 km/h (30 mph).
Do not use the speed
control in heavy traffic or
on roads that are winding,
slippery, or unpaved.
Do not shift the
transmission into N
(Neutral) with the speed control
on.
To turn speed control off
Press OFF or turn off the vehicle
ignition.
OFF ON
OFF ON
uno_speed_control_title
uno_speed-cont-on
uno_turning-cruise-off
Controls and features
40

To return to a set speed
²Press RSM. For RSM to operate,
the vehicle speed must be faster
than 48 km/h (30 mph).
To disengage speed control
²Depress the brake pedal or
²Depress the clutch pedal (if
equipped)
Disengaging the speed control will
not erase the previously
programmed set speed.
Pressing OFF will erase the
previously programmed set speed.
Indicator light
Lights when the speed control is
turned on and remains lit until
either the speed control or the
ignition is turned off.
RSM
SET
ACC
COAST
SPEED
CONT
uno_disengaging
uno_light
uno_tilt_steer
Controls and features
43

²keep the lamps on for up to
three minutes after the key is
turned to OFF
Setting autolamp
1. Make sure that the headlamp
control is in the Off position.
Leaving the headlamp control on
will override the autolamp.
2. Turn the ignition to the ON
position or start the vehicle.
3. Slide the delay control all the
way to the left.
4. Press the ON/OFF control. The
lamp indicator will glow.
5. The autolamp automatically
turns the lamps on and off. The
indicator light will illuminate when
the headlamps turn on.
OFF
AUTO
MIRROR ON
DIMON AUTOLAMP
AUTO
MIRROR ON
DIMON AUTOLAMP
uno_auto-set
uno_auto_dim_mirror
Controls and features
48