Electrical FORD FIESTA 2007 Workshop Manual

303-01 B-77 Engine - 2.OL Duratec-HE (M14) 303-01 B-77
REMOVAL
21. Disconnect the reversing lamp switch Detach the steering gear to power steering
electrical connector. fluid
reservoir return line support bracket
from the generator.
22m CAUTION:^^ brake fluid is spilt on the 25s Using the special tool, disconnect the paintwork, the affected area must be
immediately washed down with cold water. steering
gear to power steering fluid
reservoir return line from the power
Disconnect the clutch slave cylinder supply
steering fluid reservoir.
line.
Remove the spring clip. Allow
the power steering fluid to drain into a
suitable container.
23. Disconnect the air conditioning low 26. Remove the power steering fluid reservoir.
pressure switch connector.
24. N0TE:Note the position of the steering gear 27m &AUTION:C~~ the power steering fluid
to power steering fluid reservoir return line reservoir
to prevent power steering fluid
support bracket to aid installation. loss
or dirt ingress.
2006.0 Fiesta 12/2006 G451290en
procarmanuals.com

303-01 B-80 Engine - 2.OL Duratec-HE (M14) 303-01 B-80
REMOVAL
39. Remove the gearshift cables cover. 42. Detach the NC compressor from the
cylinder block and position
it to one side. /-
40. Detach the gearshift cables from the
transaxle. 43.
Remove the engine support insulator.
1. Detach the gearshift cables and the selector
cable from the selector levers.
2. Turn the abutment sleeve clockwise and
detach the cables from the bracket.
44. N0TE:Use securing straps to secure the
engine and the transaxle on the workshop
table.
Position the workshop table under the
41. Disconnect the NC high pressure switch
vehicle and carefully lower the vehicle, until
electrical connector.
the engine and transaxle assembly is in the
correct position to remove the engine
mounts.
45. Remove the engine front mount.
2006.0 Fiesta 1212006 G451290en
procarmanuals.com

303-01 B-83 Engine - 2.OL Duratec-HE (M14) 303-01 B-83
DISASSEMBLY
Engine(21 134 8)
/ 1
Special Tool(s)
Universal Flange Holding
Wrench
205-072 (1 5-030A)
Adapter for 205-072
205-072-02 (1 5-03OA-02)
Locking Tool, Flywheel
303-254 (2 1 -1 35)
Mounting Plate for
303-435-06
303-435-1
1A (21 -146D)
Socket, Spark Plug
303-499 (2 1 -202)
Pliers, Valve Stem Seal
303-508 (2 1-2 1 1 )
I I Removerllnstaller, Hose I Disassembly
1. Disconnect the generator electrical
connector.
Mounting Stand
303-435 (21 -1 87)
2006.0 Fiesta 1212006 G451309en
procarmanuals.com

303-01 B-84 Engine - 2.OL Duratec-HE (M14) 303-01 B-84
DISASSEMBLY
2. Remove the exhaust manifold upper heat 5. Remove the generator.
shield.
6. Using the special tools, mount the engine to
3. Remove the exhaust manifold lower heat the mounting stand.
shield.
7. Remove the special tool.
4. Disconnect the crankshaft position (CKP)
sensor electrical connector.
8. Drain the engine.
Allow the oil to drain into a suitable container.
9. N0TE:lnspect the oil drain plug seal for
damage. Install a new drain plug and seal
if
necessary.
2006.0 Fiesta 1212006 G451309en
procarmanuals.com

303-01 B-85 Engine - 2.OL Duratec-HE (M14) 303-01 B-85
DISASSEMBLY
Install the drain plug. 12.
Disconnect the oil pressure switch
electrical connector.
10. Detach the engine wiring harness bracket
from the intake manifold. 13.
Disconnect the fuel injector electrical
connectors.
11. Disconnect the knock sensor
(KS) electrical
connector. 14.
Disconnect the camshaft position
(CMP)
sensor electrical connector.
2006.0 Fiesta 1212006 G451309en
procarmanuals.com

303-01 B-86 Engine - 2.OL Duratec-HE (M14) 303-01 B-86
DISASSEMBLY
15. Disconnect the exhaust gas recirculation 18. Disconnect the heated oxygen (H20S)
(EGR) valve electrical connector. sensor electrical connector. f
16. Disconnect the electronic ignition (El) 19. Disconnect the throttle body (TB) electrical
electrical connector. connector.
17. Disconnect the engine coolant temperature 20. Disconnect the intake manifold runner
(ECT) sensor electrical connector. control (IMRC) electrical connector.
2006.0 Fiesta 1212006 G451309en
procarmanuals.com

303-01 B-87 Engine - 2.OL Duratec-HE (M14) 303-01 B-87
DISASSEMBLY
21. Detach the starter motor electrical
connector from the intake manifold. Discard the
gasket.
25. Remove the oil level indicator and oil level
22. Disconnect the manifold absolute pressure indicator
tube.
(MAP) sensor electrical connector.
26. Remove the intake manifold.
23. Remove the exhaust manifold lower
retaining bolts.
24. Remove the exhaust manifold.
2006.0 Fiesta 1212006 G451309en
procarmanuals.com

303-01 B-88 Engine - 2.OL Duratec-HE (M14) 303-01 B-88
DISASSEMBLY
27. Disconnect the positive crankcase
ventilation
(PCV) hose from the intake
manifold. 30.
Using the special tool, remove the spark
plugs.
31. Remove the valve cover.
28. Remove the evaporative emission
(EVAP)
valve support bracket.
32. Using the special tool, disconnect the
coolant hoses.
29. Using the special tool, disconnect the spark
plug electrical connectors.
2006.0 Fiesta 1212006 G451309en
procarmanuals.com

303-01 B-I 06 Engine - 2.OL Duratec-HE (M14) 303-01 B-106
ASSEMBLY
63. Using the special tool, connect the spark 66. Connect the positive crankcase ventilation
plug electrical connectors.
(PCV) hose to the intake manifold.
{-
64. Install the power steering pump. 67. Install the intake manifold.
65. Using the special tool, install the coolant 68. Install the oil level indicator tube and oil
hoses. level indicator.
69. N0TE:lnstall a new exhaust manifold
gasket.
N0TE:Do not tighten the exhaust manifold
retaining nuts at this stage.
2006.0 Fiesta 1212006 G451310en
procarmanuals.com

303-01 B-107 Engine - 2.OL Duratec-HE (M14) 303-01 B-107
ASSEMBLY
Install the exhaust manifold.
i
72. Attach the starter motor electrical
connector to the intake manifold.
70, Install the exhaust manifold lower retaining
bolts.
73. Connect the intake manifold runner control
(IMRC) electrical connector.
71. Connect the manifold absolute pressure
(MAP) sensor electrical connector. 74.
Connect the throttle body
(TB) electrical
connector.
2006.0 Fiesta 1212006 G451310en
procarmanuals.com