air filter FORD FIESTA 2007 Repair Manual

303-1 2-1 2 Intake Air
Distribution and Filtering 303-1 2-1 2
REMOVAL AND INSTALLATION
Air Cleaner - 1.25L Duratec-1 6V (Sigma)/l.4L Duratec-I 6V
(Sigma)/l .6L Duratec-1 6V (Sigma)(23 174 0)
Removal Installation
I. Disconnect the air cleaner outlet pipe and 1. N0TE:Locate the rear isolators onto the rear
the positive crankcase ventilation (PCV) hose
mounting pegs and push down.
from the air cleaner.
To install, reverse the removal procedure.
2. Disconnect the air intake hose from the air
cleaner.
3. Remove the air cleaner.
Remove the retaining bolts and lift the air
cleaner
up at the rear to remove.
2006.0 Fiesta 1212006 G210049en
procarmanuals.com

303-1 2-1 3 Intake Air Distribution and Filtering 303-1 2-1 3
REMOVAL AND INSTALLATION
Air Cleaner - 2.OL Duratec-HE (M14)
I. Remove the components in the order
indicated in the following
illustration(s) and
ta
ble(s).
Removal Details
Item Description Item Description
Item 2 Air cleaner outlet pipe Ifem 5 Positive crankcase ventilation (PCV) hose
I
2
3
I. Detach the air cleaner outlet pipe from the
throttle body. 1. Detach the PCV hose from the air cleaner.
5
6
7
Air cleaner outlet pipe retaining clip
Air cleaner outlet pipe See Removal Detail
Air cleaner intake pipe retaining clip
' Item 4 Air cleaner intake pipe
Positive crankcase ventilation (PCV) hose
See Removal Detail
PCV hose connector
Air cleaner See Removal Detail
1. Detach the air cleaner intake pipe from the
air cleaner.
2. To install, reverse the removal procedure.
4
2006.0 Fiesta 1212006 G421938en
Air cleaner intake pipe
See Removal Detail
procarmanuals.com

303-1 2-1 4 Intake Air Distribution and Filtering 303-1 2-1.4
REMOVAL AND INSTALLATION
Ifem 7 Air cleaner
~CAUTION:M~~~ sure the air cleaner is
removed from the air cleaner mountings in
a vertical direction. Failure to follow this
instruction may cause damage to the air
cleaner and air cleaner mountings.
Detach the air cleaner from the air cleaner
mountings and
remov,e the air cleaner.
2006.0 Fiesta 12/2006 G421938en
procarmanuals.com

303-1 4-30 Electronic Engine Controls 303-1 4-30
REMOVAL AND INSTALLATION
Heated Oxygen Sensor (H02S)(29 220 0) /
Removal
Special Tool(s) 4. Disconnect the H02S electrical connector. (. .. >k,
1. Remove the air cleaner. For additional
information, refer to Section 303-1 2 [Intake
Air Distribution and Filtering].
5. Remove the exhaust manifold heat shield.
2. Disconnect the ignition coil pack electrical
connector.
23050
3. Detach the ignition coil pack and position it
to one side
Socket, Fuel Injector (22mm)
31 0-063 (23-050)
6. Using the special tool, remove the H02S.
Installation
A CAUTI0N:When installing a new H02S, it
is possible that the new component will be (- supplied with a longer cable than the one ,
removed. It is important that the cable is
routed and secured in such a way that
it
2006.0 Fiesta 1212006 G210054en
procarmanuals.com

Automatic Transmission/Transaxle -
Vehicles With: 4-Speed Automatic
307-01 -62 Transmission (AW81-40) 307-01 -62
REMOVAL AND INSTALLATION
Transaxle
Special Tool(s)
I I Separator, Ball Joint
Support Bar, Engine
303-290A
Adapter for 303-290A
303-290-01 (21 -1 40-01
)
General Eaui~ment
I Securing strap I
General Equipment
Transmission jack
I Worldwide diagnostic system (WDS) I
Materials
Name S~ecification
1 Grease I WSD-MI C230-A I
Removal
A WARN1NG:Refer to the Material Safety Data
Sheets for the Automatic Transmission
Fluid E-AW. Failure to follow this
instruction may
result in personal injury.
Certain Transmission and Power Steering
fluids supplied to Ford contain additives
which may cause skin irritation or other
skin reactions after contact.
For
additional information, refer to: Health
and Safety Precautions (1 00-00 General
Information, Description and Operation).
See
- Transmission Fluids. f
1. Remove the air cleaner. \.
For additional information, refer to: Air
Cleaner - 1.25L Duratec-1 6V (Sigma)/ln4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma) (303-12 Intake Air Distribution and
Filtering, Removal and Installation).
2. Disconnect the powertrain control module
(PCM) electrical connector.
For
additional information, refer to:
Powertrain
Control Module (PCM) - 1.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V
(Sigma)ll .6L Duratec-1 6V (Sigma) (303-1 4
Electronic Engine Controls, Removal and
Installation).
3. Remove the battery tray.
For
additional information, refer to: Battery
Tray (41 4-01 Battery, Mounting and
Cables,
Removal and Installation).
2006.0 Fiesta 1212006 G371506en
procarmanuals.com

Automatic Transmission/Transaxle -
Vehicles With: 4-Speed Automatic
307-01 -76 Transmission
(AW81-40) 307-01 -76
REMOVAL AND INSTALLATION
46. Install the battery tray.
For
additional information, refer to: Battery
Tray (414-01 Battery, Mounting and
Cables, Removal and Installation).
47. Connect the powertrain control module
(PCM) electrical connector to the PCM.
For
additional information, refer to:
Powertrain
Control Module (PCM) - 1.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V
(Sigma)ll .6L Duratec-1 6V (Sigma) (303-1 4
Electronic Engine Controls, Removal and
Installation).
48. Install the air cleaner.
For additional information, refer to: Air
Cleaner - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll.GL Duratec-1 6V
(Sigma) (303-1 2 Intake Air Distribution
and
Filtering, Removal and Installation).
49. Check the transmission fluid level and top
up with
clean automatic transmission fluid
if necessary.
For
additional information, refer to:
Transmission
Fluid Level Check (307-01
Automatic
Transmission/Transaxle -
Vehicles With: 4-Speed Automatic
Transmission
(AW81-40), General
Procedures).
50.
N0TE:Only carry out the following step
when a new
transaxle has been installed.
Using worldwide diagnostic system (WDS),
reset the transmission control module (TCM).
2006.0 Fiesta 1212006 G371506en
procarmanuals.com

Manual Transmission/Transaxle and Clutch -
308-00-1 2 General Information 308-00-1 2
GENERAL PROCEDURES
Clutch System Bleeding(l6 843 0)
Special Tool(s) 6. Fill the reservoir of the special tool with (,, .
I Hand Vacuum approximately 100 ml of new brake fluid.
7. N0TE:Make sure that the special tool
reservoir is positioned lower than the bleed
nipple.
Install the special tool.
Super DOT 4 Brake
1 Fluid
I
Materials
Name Specification
ESD-M6C57-A
A WARNING: Brake fluid contains polyglycol
ethers and polyglycols. Avoid contact with
the eyes. Wash hands thoroughly after
handling. If brake fluid contacts the eyes,
flush the eyes for 15 minutes with cold
running water. Get medical attention if
irritation persists. If taken internally, drink
8. Using the special tool, bleed the clutch
water and induce vomiting. Get medical system.
attention immediately. Failure to follow
Pump approximately 80 ml of brake fluid into
these instructions may result in personal the clutch svstem. (
injury. w
9. Close the bleed nipple. A CAUTI0N:Y brake fluid is spilt on the
paintwork, the affected area must be 10.
Remove the special tool.
immediately washed down with cold water.
11. Lower the vehicle, if necessary.
N0TE:lf proprietary brake bleeding equipment is
available, this can be used to bleed the clutch
system, following the method below. The maximum
pressure must not exceed
1.5 bar.
N0TE:The clutch control system is self-venting.
The components are arranged in such a way that
small amounts of air trapped in the system are
removed automatically during clutch operation.
12. In order to remove any small amounts of
trapped air remaining in the system,
operate the clutch pedal several times
(maximum five times), using the full clutch
pedal travel.
13. Check the fluid level in the brake fluid
reservoir and top up to the MAX mark with
brake fluid if necessary.
1. Remove the air cleaner, if necessaryfor 14. Install the battery tray, if necessary.
additional information, refer to
Section
303-12 [Intake Air Distribution and 15.
Install the battery, if necessary. For
Filtering]. additional
information, refer to
Section 414-01 [Battery, Mounting and
2. Remove the battery, if necessary. For
Cablesl.
additional information, refer to
Section
414-01 [Battery, Mounting and . 16. Install the air cleaner, if necessary. For
Cables]. additional
information, refer to
Section 303-1
2 [Intake Air Distribution and - 3. Remove the battery tray, if necessary.
Filtering]. (' L 4. Drain the brake fluid reservoir.
17. Test the clutch control system for normal "I-
5. Raise and support the vehicle, if necessary. operation.
For additional information, refer to
Section 100-02 [Jacking and Lifting].
2006.0 Fiesta 1212006 GI 83752en
procarmanuals.com

308-02-7 Clutch Controls 308-02-7
REMOVAL AND INSTALLATION
Clutch Master Cylinder(l6 856 0) /
Removal 4. Remove the battery tray. For additional
information, refer to:
CAUTI0N:H brake fluid is spilt on the
paintwork, the affected area must be Battery
Tray (41 4-01, Removal and
immediately washed down with cold water. Installation),
Battery Tray - 2.OL Duratec-HE (M14) (414-01
All vehicles Battery, Mounting and Cables, Removal
and Installation).
Left-hand drive vehicles
1. Using a suitable syringe, remove brake fluid
from the brake fluid reservoir until the brake All vehicles
fluid level is at the MIN mark.
5. N0TE:Plug the brake fluid reservoir to
prevent
fluid loss or dirt ingress. Right-hand drive vehicles Disconnect the clutch master cylinder supply 2. Remove the air cleaner. For additional hose from the brake fluid reservoir.
information, refer to: (303-1 2 Intake Air
Distribution and Filtering)
Push the clip to release the clutch master
cylinder supply hose.
3. Disconnect the two vacuum hoses.
6. Remove the clutch master cylinder supply
Detach the vacuum hoses from the battery hose.
clamp clip. Release the clutch master cylinder supply
hose retaining clip.
Allow the fluid to drain into a suitable
container.
Air Cleaner - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)/l .6L Duratec-I 6V
(Sigma) (Removal and lnstallation),
Air Cleaner - 1.3L Duratec-8V (Rocam)
(Removal and lnstallation),
Air Cleaner - 1.4L Duratorq-TDCi (DV) Diesel
(Removal and lnstallation),
(, I Air Cleaner - 2.OL Duratec-HE (M14) (Removal
and
Installation),
Air Cleaner - 1.6L Duratorq-TDCi (DV) Diesel
(Removal and lnstallation).
7. N0TE:Plug the clutch slave cylinder supply
line to prevent fluid loss or dirt ingress.
1
2006.0 Fiesta 1212006 GI 52706en
procarmanuals.com

308-02-1 0 Clutch Controls 308-02-1 0
REMOVAL AND INSTALLATION
7. Bleed the clutch system. For additional
information, refer to: (308-00 Manual
Transmission/Transaxle and Clutch - General
Information)
Clutch System Bleeding (General
Procedures),
Clutch System Bleeding - Vehicles With:
Automated Gearshift
(General Procedures).
Left-hand drive vehicles
8. Install the battery tray. For additional
information, refer to:
Battery Tray (414-01,
Removal and
Installation),
Battery Tray - 2.OL Duratec-HE (M14) (414-01
Battery, Mounting and
Cables, Removal
and Installation).
9. Connect the two vacuum hoses.
Attach the vacuum hoses to the battery
clamp clip.
Right-hand drive vehicles
10. Install the air cleaner. For additional
information, refer to: (303-12 Intake Air
Distribution and
Filtering)
Air Cleaner - 1.25L Duratec-1 6V (Sigma)/l.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma) (Removal and lnstallation),
Air Cleaner - 1.3L Duratec-8V (Rocam)
(Removal and lnstallation),
Air Cleaner - 1.4L Duratorq-TDCi (DV) Diesel
(Removal and lnstallation),
Air Cleaner - 2.OL Duratec-HE (M14) (Removal
and lnstallation).
2006.0 Fiesta 12/2006 GI 52706en
procarmanuals.com

308-03-23 Manual Transmission/Transaxle 308-03-23
REMOVAL
Transaxle - 1.25L Duratec-1 6V (Sigma)/l.4L Duratec-1 6V
i (Sigma)/l .6L Duratec-1 6V (Sigma)(l6 11 4 0)
I I Support Bar, Engine
Adapter for 303-290A
303-290-0 1 (2 1
- 1 40-0 1 )
21 14002
Adapter for 303-290A
303-290-02 (2 1 -1 40-02)
21 14003
General Equipment I
Adapter for 303-290A
303-290-03A (2 1-1 40-03A)
16089
I Retaining strap I
Remover, Halfshaft
308-256 (1 6-089)
1 Transmission jack I
Removal
All vehicles
1. Remove the air cleaner.
For additional information, refer to: Air
Cleaner - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma) (303-1 2 Intake Air Distribution and
Filtering, Removal and Installation).
2. Remove the battery tray.
For
additional information, refer to: Battery
Tray (414-01 Battery, Mounting and
Cables,
Removal and Installation).
3. Disconnect the powertrain control module
(PCM) electrical connector.
4. Loosen the strut and spring
assembly top
mount nuts by three turns on both sides.
2006.0 Fiesta 1212006 GI 13290en
procarmanuals.com