check oil FORD FOCUS 2013 3.G ST Supplement Manual

Oil pressure gauge
Indicates engine oil pressure.
During normal driving the indicated oil pressure will vary with engine
speed, the pressure rising as engine speed rises and dropping as engine
speed drops.
If the engine oil pressure drops below the normal range, the oil pressure
gauge pointer will drop into the red section of the gauge scale and the
engine oil pressure warning lamp in the main instrument cluster will
illuminate. Stop the vehicle as soon as safely possible and switch off the
engine immediately. Check the oil level and add oil if needed.
Vehicle Specifications
Item Description
TransmissionGFT MMT6 6-speed manual with 240 mm clutch and
dual mass flywheel
Gear ratiosGear Ratio Final Drive
1st 3.231 4.063
2nd 1.952 4.063
3rd 1.321 4.063
4th 1.029 4.063
5th 1.129 2.955
6th 0.943 2.955
Reverse 4.600 2.955
Focus ST Unique Features
7
2013 Focus ST(stf)
Supplement, 1st Printing
USA(fus)

ENGINE SPECIFICATIONS
Engine 2.0L EcoBoost engine
Cubic inches 122
Required fuel Minimum 87 octane
Firing order 1–3–4–2
Ignition system Coil on plug
Compression ratio 9.3:1
Spark plug gap 0.027-0.031 in. (0.70-0.80 mm)
Drivebelt Routing
2.0L EcoBoost
A. The long drivebelt is on the first pulley groove closest to the engine.
B. The short drivebelt is on the second pulley groove farthest from the
engine.
CHECKING THE ENGINE OIL
Refer to thescheduled maintenance informationfor the appropriate
intervals for checking the engine oil.
1. Make sure the vehicle is on level ground.
2. Turn the engine off and wait 15 minutes for the oil to drain into the
oil pan.
Note:The oil dipstick on the Focus ST is integrated into the oil drain
back system. The oil reading on the dipstick will be influenced by oil
draining back into the sump from the cylinder head if the oil level is
checked without waiting 15 minutes after shutdown.
3. Set the parking brake and make sure the transmission selector lever is
securely latched in first gear.
4. Open the hood. Protect yourself from engine heat.
A
B
Capacities and Specifications
21
2013 Focus ST(stf)
Supplement, 1st Printing
USA(fus)

5. Locate and carefully remove the engine oil level dipstick.
6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.
A. MIN
B. MAX
•If the oil level is between the MIN and MAX marks, the oil level is
acceptable. DO NOT ADD OIL.
•If the oil level is below the MIN mark, add enough oil to raise the level
within the MIN and MAX marks
•The maximum oil level is between the upper hash mark and the MAX
mark. Oil levels above this range may cause engine damage. Some oil
must be removed from the engine by an authorized dealer.
7. Put the dipstick back in and make sure it is fully seated.
ENGINE COOLANT
The concentration and level of engine coolant should be checked at the
mileage intervals listed in thescheduled maintenance information.
Note:Make sure that the level is between the MIN and MAX marks on
the engine coolant reservoirs.
Note:For best results, coolant concentration should be tested with a
refractometer such as Rotunda tool 300-ROB75240E available from your
dealer. Ford does not recommend the use of hydrometers or coolant test
strips for measuring coolant concentrations.
Note:Coolant expands when it is hot. The level may extend beyond the
MAX mark. If the level is at the MIN mark, add coolant immediately.
Be sure to read and understandPrecautionsin yourOwner’s Manual.
If the coolant has not been checked at the recommended interval, the
engine or intercooler coolant reservoir may become low or empty. If the
reservoir is low or empty, add coolant to the reservoir. Refer toAdding
coolantin this chapter.
Note:Automotive fluids are not interchangeable; do not use engine
coolant/antifreeze or windshield washer fluid outside of its specified
function and vehicle location. For more information about engine coolant,
see theMaintenancechapter of theOwner’s Manual.
Capacities and Specifications
22
2013 Focus ST(stf)
Supplement, 1st Printing
USA(fus)