coolant FORD MUSTANG 1969 Volume One Chassis

07-01-04
General Transmission Service

07-01-04

taching bolts to the proper torque. If

necessary, replace the gasket.

Check the fluid filler tube connec-

tion at the transmission case or pan.

If leakage is found here, install a new

O-ring or tighten the fitting to the

specified torque.

Check the fluid lines and fittings

between the transmission and the

cooler in the radiator tank for loose-

ness,
wear, or damage. If leakage can-

not be stopped by tightening a fitting,

replace the damaged parts.

Check the engine coolant in the ra-

diator. If transmission fluid is present

in the coolant, the cooler in the radia-

tor is probably leaking.

The cooler can be further checked

for leaks by disconnecting the lines

from the cooler fittings and applying

50-75 psi air pressure to the fittings.

Remove the radiator cap to relieve the

pressure build at the exterior of the oil

cooler tank. If the cooler is leaking

and will not hold this pressure the

cooler must be replaced. Cooler re-

placement is described in the Cooling

System Section of Group 11.

If leakage is found at either the

downshift control lever shaft or the

manual lever shaft, replace either or

both seals.

Inspect the pipe plug on the left

side of the transmission case at the

front. If the plug shows leakage, tor-

que the plug to specifications. If tight-

ening does not stop the leaks, replace

the plug. On a C6 transmission, a TV

pressure plug is also provided on the

right rear side of the case.

When converter drain plugs leak,

remove drain plugs with a six-point

wrench. Coat the threads with FoMo-

Co Perfect Seal Sealing Compound or

its equivalent, and install the plugs.

Torque the drain plugs to specifica-

tion. Fluid leakage from the converter

housing may be caused by engine oil

leaking past the rear main bearing or

from oil gallery plugs, or power steer-

ing oil leakage from steering system.

Be sure to determine the exact cause

of the leak before repair procedures

are started.

Oil-soluble aniline or fluorescent dyes

premixed at the rate of 1/2 teaspoon

of dye powder to 1/2 pint of transmis-

sion fluid have proved helpful in locat-

ing the source of the fluid leakage.

Such dyes may be used to determine

whether an engine oil or transmission

fluid leak is present or if the fluid in

the oil cooler leaks into the engine

coolant system. A black light, how-

ever, must be used with the fluorescent

dye solution.
DISHED OR

FLAT WASHER

" O.D.,
a" STEEL PLATE

5/8"X \W,

DRILL TO SUIT
HEX. HEAD SCREW

3/8"-24 X Vl

HEX. NUT W—
24

WELD

TOGETHER

WING
NUT

>/2"_13
THREAD

CHAIN,
10"
LONG
RUBBER PLUG

1
Vi" DIA. X 2"

LONG Vl"

HOLE THRU

APPROXIMATELY

40 DUROMETER
FLAT WASHER

Vs" O.D.

PLUG

VALVE
STANDARD BOLT

W-13
X 4Vl"

LONG SQUARE

THREAD
END

REMOVE HEAD

AND WELD
TO

WASHER

STANDARD 1/8" FITTING-87971-S FOR

RETAPPED DRAIN PLUG THREADS-USE

1/4" OVERSIZE FITTING-87973-S

D 1067-B
WELD TOGETHER

SECURELY—MUST

NOT LEAK

FIG. 2—Converter Leak Checking Tool

CONVERTER LEAKAGE

CHECK

If there are indications that the

welds on the torque converter are

leaking, the converter will have to be

removed and the following check

made before the unit is replaced.

A leak checking tool (Fig. 2) can be

made from standard parts. The tool

can be used to check all converters.

1.
Install the plug in the converter

(Fig. 3) and expand it by tightening

the wing nut. Attach the safety chains.

2.
Install the air valve in one of the

drain plug holes.

3.
Introduce air pressure into the

converter. Check the pressure with a

tire gauge and adjust it to 20 psi.

4.
Place the converter in a tank of

water. Observe the weld areas for

bubbles. If no bubbles are observed, it

may be assumed that the welds are

not leaking.

ENGINE IDLE SPEED CHECK

Check and, if necessary, adjust the

engine idle speed, using the procedure

given in Group 10.

If the idle speed is too low, the en-

gine will run roughly. An idle speed

that is too high will cause the vehicle

to creep, have harsh engagements and

harsh closed-throttle downshifts.
ANTI-STALL DASHPOT

CLEARANCE CHECK

After the engine idle speed has been

properly adjusted, check the anti-stall

dashpot clearance. Follow the proce-

dure given in Group 10 for checking

and adjusting this clearance.

MANUAL LINKAGE CHECKS

Correct manual linkage adjustment

is necessary to position the manual

valve for proper fluid pressure direc-

tion to the different transmission com-

ponents. Improperly adjusted manual

Tire Pressure Gauge

D1921-A

FIG. 3—Converter Leak Checking

Tool Installationprocarmanuals.com