brake FORD MUSTANG 1996 4.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1996, Model line: MUSTANG, Model: FORD MUSTANG 1996 4.GPages: 332, PDF Size: 3.21 MB
Page 8 of 332
5
%*
[IN06000( ALL)01/95]
Breaking Your Vehicle In
*
[IN06100( ALL)03/95]
Your new vehicle goes through an adjustment or
break-in period during the first 1,000 miles
(1,600 km) that you drive it. During the break-in
period, you need to pay careful attention to how
you drive your vehicle.
%*
[IN06300( ALL)01/95]
q
Avoid sudden stops.Because your vehicle
has new brake linings, you should take these
steps:
*
[IN06400( ALL)01/95]
Ð Watch traffic carefully so that you can
anticipate when to stop.
*
[IN06500( ALL)01/95]
Ð Begin braking well in advance.
*
[IN06600( ALL)01/95]
Ð Apply the brakes gradually.
*
[IN06700( ALL)01/95]
The break-in period for new brake linings
lasts for 100 miles (160 km) of city driving or
1,000 miles (1,600 km) of highway driving.
%*
[IN06800( ALL)01/95]
q
Use only the type of engine oil that Ford
recommends.SeeEngine oil recommendations
in the Index. Do not use special ªbreak-inº
oils.
*
[IN07000( ALL)04/95]
Your vehicle is equipped with an Electronic
Powertrain Control Module that limits engine
and/or vehicle speeds with a cut-out mode to
promote durability.
%
*
[IN07100( ALL)04/95]
Cleaning the Outside of Your
Vehicle
*
[IN07130( ALL)07/95]
Pollen, bird droppings and tree sap can damage
the paint, especially in hot weather. Wash your
vehicle as often as necessary to keep it clean.
*
[IN07160( ALL)07/95]
Take similar precautions if your vehicle is
exposed to chemical industrial fallout.
File:02rcinm.ex
Update:Wed Mar 27 09:22:17 1996
Page 13 of 332
11
*
[SR03200( ALL)09/95]
RWARNING
Lock the doors of your vehicle before
driving to lessen the risk of the door
coming open in a collision.
%
*
[SR03700( ALL)05/95]
Combination Lap and Shoulder
Belts
*
[SR03800( ALL)01/95]
While your vehicle is in motion, the combination
lap and shoulder belt adjusts to your movement.
However, if you brake hard, corner hard or if
your vehicle receives an impact of 5 mph
(8 km/h) or more, the lap and shoulder belt
locks and helps reduce your forward movement.
*
[SR04100( ALL)05/95]
After you get into your vehicle, close the door
and lock it. Then adjust the seat to the position
that suits you best.
[SR04300(M )06/93]
Before fastening the front seat belt, make sure
the shoulder belt passes through the belt holder
on the top of the seatback.
[SR04400( ALL)06/93]
To fasten the belt,pull the lap/shoulder belt
from the retractor so that the shoulder portion of
the belt crosses your shoulder and chest. Be sure
the belt is not twisted. If it is, remove the twist.
Insert the belt tongue into the proper buckle
until you hear a snap and feel it latch. Make
sure the tongue is securely fastened in the
buckle.
File:03rcsrm.ex
Update:Wed Mar 27 09:23:48 1996
Page 51 of 332
50
*
[ST04300( ALL)05/95]
ON allows you to test your vehicle's warning
lights (except the brake system warning light) to
make sure they work before you start the
engine. The key returns to the ON position once
the engine is started and remains in this position
while the engine runs.
*
[ST04400( ALL)03/95]
START cranks the engine. Release the key once
the engine starts so that you do not damage the
starter. The key should return to ON when you
release it. The START position also allows you
to test the brake warning light.
%*
[ST04900( ALL)02/95]
Removing the Key From the Ignition
[ST05700(M )03/95]
1. Put the gearshift in P (Park) (automatic
transmission) or 1 (First) (manual
transmission).
*
[ST05800( ALL)01/95]
2. Set the parking brake fully.
[ST06000(M )03/95]
3. Turn the ignition to the OFF (manual
transmission) or LOCK (automatic
transmission).
[ST06100(M )03/95]
4. Push in the key release button until it
catches and stays in (manual transmission
only).
[ST06250(M )03/95]
quarter page art:0010619-B
Key release button (manual transmission only)
[ST06500(M )03/95]
5. Turn the key to LOCK (manual
transmission).
*
[ST06600(M )05/95]
6. Remove the key.
File:04rcstm.ex
Update:Wed Mar 27 09:28:42 1996
Page 52 of 332
51 [ST06650(M )05/95]
NOTE: If your vehicle has an automatic
transmission, the gearshift lever must
be in the P (Park) position to remove
the key from the ignition.
%*
[ST06675( ALL)05/95]
If the key is stuck in the LOCK position, move
the steering wheel left or right until the key
turns freely.
%*
[ST06700( ALL)05/95]
If the driver's door is open while the key is still
in the ignition, a warning chime sounds.
*
[ST06800(M )05/95]
RWARNING
Always set the parking brake fully and
make sure that the gearshift is latched in
P (Park) (automatic transmission) or 1
(First) (manual transmission).
*
[ST06875( ALL)01/93]
RWARNING
Do not leave children, unreliable adults,
or pets alone in your vehicle. They could
accidentally injure themselves or others
through inadvertent operation of the
vehicle. Further, on hot, sunny days,
temperatures in a closed vehicle could
quickly become high enough to cause
severe and possibly fatal injuries to
people as well as animals.
%
*
[ST07000( ALL)10/95]
Fuel-Injected Engines
*
[ST07100( ALL)10/95]
When starting a fuel-injected engine,the most
important thing to remember is to avoid
pressing down on the accelerator before or
during starting. Only use the accelerator when
you have problems getting your vehicle started.
SeeStarting Your Enginein this chapter for
details about when to use the accelerator while
you start your vehicle.
File:04rcstm.ex
Update:Wed Mar 27 09:28:42 1996
Page 53 of 332
52
*
[ST07300( ALL)03/95]
Starting Your Vehicle
%*
[ST07400( ALL)05/94]
Preparing to Start Your Vehicle
*
[ST07500( ALL)09/95]
RWARNING
Do not start your vehicle in a closed
garage or other enclosed area. Never sit in
a stopped vehicle for more than a short
period of time with the engine running.
Exhaust fumes are toxic. SeeGuarding
Against Exhaust Fumesin this chapter for
more instructions.
*
[ST07600( ALL)01/95]
Before you start your vehicle, do the following:
*
[ST07700( ALL)08/95]
1. Make sure all occupants in the vehicle
buckle their safety belts. SeeSafety Restraints
in the Index for more details.
*
[ST07800( ALL)03/95]
2. Make sure the headlamps and other
accessories are turned off when starting.
[ST07900(M )03/95]
3.If you have an automatic transmission,
make sure that the gearshift is in P (Park)
and the parking brake is set before you turn
the key.
[ST08000(M )03/95]
If you have a manual transmission, make
sure that the parking brake is fully set, push
the clutch pedal to the floor, and put the
gearshift into Neutral before you turn the
key.The starter will operate only if the
clutch pedal is pushed in all the way.
*
[ST08400( ALL)03/95]
Before you start your vehicle, you should test
the warning lights on the instrument panel to
make sure that they work. Refer to theWarning
Lights and Gaugeschapter.
File:04rcstm.ex
Update:Wed Mar 27 09:28:42 1996
Page 55 of 332
54
*
[ST10473( ALL)08/95]
Whenever you start your vehicle, release the key
as soon as the engine starts. Excessive cranking
could damage the starter.
*
[ST10476( ALL)05/95]
After you start the engine, let it idle for a few
seconds. Keep your foot on the brake pedal and
put the gearshift lever in gear. Release the
parking brake. Slowly release the brake pedal
and drive away in the normal manner.
[ST10478( ALL)12/94]
NOTE: Your vehicle has an interlock that
prevents you from shifting out of P
(Park) unless your foot is on the brake
pedal.
%*
[ST10480( ALL)04/95]
If the engine does not start after two attempts:
*
[ST10492( ALL)04/95]
1. Turn the ignition key to the OFF position.
*
[ST10494( ALL)04/95]
2. Press the accelerator all the way to the floor
and hold it.
*
[ST10496( ALL)04/95]
3. Turn the ignition key to the START position.
*
[ST10497( ALL)04/95]
4. Release the ignition key when the engine
starts.
*
[ST10498( ALL)04/95]
5. Release the accelerator gradually as the
engine speeds up. Then drive away in the
normal manner.
*
[ST10500( ALL)04/95]
If the engine still does not start, the fuel pump
shut-off switch may have been triggered. For
directions on how to reset the switch seeFuel
Pump Shut-Off Switchlater in this chapter.
*
[ST11100( ALL)07/95]
A computer system controls the engine's idle
speed. When you start your vehicle, the engine's
idle speed normally runs higher than when it's
warmed up. These faster engine speeds will
make your vehicle move slightly faster than its
normal idle speed. It should, however, slow
down after a short time. If it does not, have the
idle speed checked.
File:04rcstm.ex
Update:Wed Mar 27 09:28:42 1996
Page 64 of 332
64
[LG02710(M )06/93]
The Cluster
[LG02715(M )06/93]
The following warning lights and gauges are on
the cluster. All of the warning lights and gauges
alert you to possible problems with your vehicle.
Some of the lights listed are optional. The
following sections detail what each of these
indicators means.
%*
[LG02900( ALL)06/95]
Brake System Warning Light
*
[LG03000( ALL)03/95]
The warning light for the brakes can show two
things Ð that the parking brake is not fully
released, or that the brake fluid level is low in
the master cylinder reservoir. If the fluid level is
low, the brake system should be checked by a
qualified service technician.
[LG03050(M )05/95]
one inch art:0011354-A[LG03100( ALL)01/95]
This light comes on when the parking brake is
set, or if it is not set, it comes on briefly when
you turn the ignition key to START. It normally
goes off shortly after the engine starts and you
release the parking brake. If the light stays on
after you have fully released the parking brake,
have the hydraulic brake system serviced.
*
[LG03200( ALL)05/95]
RWARNING
The BRAKE light indicates that the brakes
may not be working properly. Have the
brakes checked immediately.
File:05rclgm.ex
Update:Wed Mar 27 09:29:39 1996
Page 65 of 332
65 % [LG03475( ALL)05/94]
Anti-Lock Brake System Light
(If equipped)
[LG03500( ALL)05/94]
This warning light will go on each time you
start your vehicle. If it remains on for longer
than five seconds, you should shut off your
engine and restart. If the anti-lock brake light
stays on, this indicates that the anti-lock feature
is disabled and should receive immediate
attention by a qualified service technician.
Normal braking is not affected unless the brake
warning light is also lit.
[LG03680( ALL)05/95]
one inch art:0011194-B*
[LG03700( ALL)05/95]
RWARNING
If the anti-lock brake system warning
light remains on or comes on while
driving, have the braking system checked
by a qualified service technician as soon
as possible.
*
[LG03800( ALL)10/95]
NOTE: If a fault occurs in the anti-lock
system, and the brake warning light is
not lit, the anti-lock system is disabled
but normal brake function remains
operational.
% [LG03900(M )05/95]
Low Oil Level Light (4.6L engines only)
[LG04000(M )06/93]
This light indicates that the level of the oil in
your engine is low and you have to add more
oil. The light may glow for a moment when the
engine is started. If the light stays on while the
engine is running, check the engine oil.
File:05rclgm.ex
Update:Wed Mar 27 09:29:39 1996
Page 84 of 332
84 [IP33000( ALL)12/94]Clear away any snow that is on the rear
window before using the defroster. With the
engine running, push the defrost button.
[IP33100( ALL)12/94]
After approximately 10 minutes, the defroster
will turn off. If the window is still not clear,
turn the defroster on again.
[IP33200( ALL)12/94]
The defroster will turn off when the ignition key
is turned to the OFF position.
*
[IP33300( ALL)02/95]
The heating elements are bonded to the inside of
the rear window. Do not use sharp objects to
scrape the inside of the rear window or use
abrasive cleaners to clean it. Doing so could
damage the heating elements.
%
*
[IP34200( ALL)01/95]
The Interior and Exterior Lights
%*
[IP34310( ALL)01/95]
Daytime Running Light System
*
[IP34312( ALL)03/95]
(Canadian vehicles only)
*
[IP34320( ALL)03/95]
The Daytime Running Light (DRL) system turns
the high beam headlamps on, with a reduced
light output, when:
*
[IP34325( ALL)03/95]
q
The headlamp system is in the OFF position,
and
*
[IP34330( ALL)03/95]
q
The vehicle is running, and
*
[IP34340( ALL)01/95]
q
The vehicle has a fully released parking
brake.
*
[IP34363( ALL)09/95]
NOTE: The high beam indicator will not turn
on in the flash-to-pass mode during
nighttime driving.
*
[IP34365( ALL)01/95]
NOTE: You may notice that the lights flicker
when the vehicle is turned on or off.
This is a normal condition.
File:06rcipm.ex
Update:Wed Mar 27 09:30:23 1996
Page 86 of 332
86 [IP35200( ALL)12/91]When you turn on the headlamps, the parking
lamps, tail lamps, and side markers
automatically turn on. But you can turn on the
parking lamps, tail lamps, and side markers
without turning on the headlamps.
*
[IP36100( ALL)01/95]
For more information about how the high beams
work, refer to theSteering Column Controls
chapter.
%*
[IP36200( ALL)08/95]
Cleaning the Exterior Lamps
*
[IP36300( ALL)08/95]
Do not use dry paper towel, chemical solvents
or abrasive cleaners to clean the lamps, as these
may cause scratches or crack the lamps.
%*
[IP42400(M )04/95]
Fog Lamps (If equipped)
[IP42600(M )06/93]
The fog lamps switch is located on the console
to the left of the parking brake. The fog lamps
act as a supplement to the low beam headlamps
under limited visibility conditions such as rain,
snow, dust or fog and operate only when the
low beam headlamps are on.
[IP42750(M )08/93]
one third page art:0011228-A
Fog lamp switch
[IP44200(M )03/95]
q
To turn the fog lamps on, push the concave
side of the rocker switch. An indicator light
will glow when the lamps are on.
[IP44400(M )03/95]
q
To turn off, push the raised side of the
switch.
File:06rcipm.ex
Update:Wed Mar 27 09:30:23 1996