engine coolant FORD MUSTANG 2001 4.G User Guide

Engine coolant refill procedure-3.8L V6 engine
Use the following procedure when refilling
the cooling system of a vehicle equipped
with a 3.8L V6 engine. Failure to follow this
warning may result in damage to the engine and
engine cooling system.
The following procedure should be used when
refilling the cooling system of a 3.8L V6 engine after
it has been drained or become extremely low.
1. Remove the cap
from the engine
coolant reservoir.
2. Open the cooling
system vent plug.
3. Remove the radiator
cap as previously
outlined.
4. Add a50/50 mixtureof engine coolant and
distilled water to the radiator until full.
5. Add a50/50 mixtureof engine coolant and
distilled water to the engine coolant reservoir until
the coolant level is at the ªcold fill levelº as listed on
the reservoir.
6. Close the cooling system vent plug.
7. Reinstall the engine coolant reservoir cap.
8. Reinstall the radiator cap.
9. Start and idle the engine until the upper radiator
hose is warm (this indicates the thermostat is open
and coolant is flowing through the entire system).
10. Immediately shut the engine off.
11. Wrap a thick cloth around the radiator cap and
cautiously remove the radiator cap.
12. Add a50/50 mixtureof engine coolant and
distilled water to the radiator until full.
2
31
Maintenance and care
162

13. Reinstall the radiator cap.
14. Check the coolant level in the reservoir before
you drive your vehicle the next few times (with the
engine cool).
15. If necessary, add a50/50 mixtureof engine
coolant and distilled water to the engine coolant
reservoir until the coolant level is at the ªcold fill
levelº as listed on the reservoir.
If you are unsure of how to operate the cooling
system vent plug when adding engine coolant to the
3.8L V6 engine, contact your dealer.
Engine coolant refill procedure-4.6L V8 engine
The following procedure should be used when
refilling the cooling system of a 4.6L V8 engine after
it has been drained or become extremely low.
1. Remove the pressure relief cap from the engine
coolant reservoir as previously outlined.
2. Slowly add a50/50 mixtureof engine coolant
and distilled water to the engine coolant reservoir
until the coolant level is at the ªcold fill levelº as
listed on the reservoir.
3. Reinstall the pressure relief cap.
4. Start and idle the engine until the upper radiator
hose is warm (this indicates the thermostat is open
and coolant is flowing through the entire system).
5. Shut the engine off and let it cool.
6. Remove the pressure relief cap from the engine
coolant reservoir as previously outlined.
7. Add a50/50 mixtureof engine coolant and
distilled water to the engine coolant reservoir until
the coolant level is at the ªcold fill levelº as listed on
the reservoir.
8. Reinstall the pressure relief cap.
9. Check the coolant level in the reservoir before
you drive your vehicle the next few times (with the
engine cool).
Maintenance and care
163

10. If necessary, add a50/50 mixtureof engine
coolant and distilled water to the engine coolant
reservoir until the coolant level is at the ªcold fill
levelº as listed on the reservoir.
After any coolant has been added, check the coolant
concentration see Checking Engine Coolant section).
If the concentration is not 50/50 (protection to
±34ÉF/±36ÉC), drain some coolant and adjust the
concentration. It may take several drains and
additions to obtain a 50/50 coolant concentration.
Whenever coolant has been added, the coolant level in
the coolant reservoir should be checked the next few
times you drive the vehicle. If necessary, add enough
50/50 concentration of engine coolant and distilled
water to bring the liquid level to the proper level.
If you have to add more than 1.0 liter (1.0 quart) of
engine coolant per month, have your dealer check
the engine cooling system. Your cooling system may
have a leak. Operating an engine with a low level of
coolant can result in engine overheating and possible
engine damage.
Recycled engine coolant
Ford Motor Company recommends the use of a
recycled engine coolant produced by Ford-approved
processes in vehicles originally equipped with
Motorcraft Premium Engine Coolant (green-colored).
However, not all coolant recycling processes produce
coolant that meets Ford specification
ESE-M97B44±A. Use of such coolant may harm the
engine and cooling system components.
Ford Motor Company does NOT recommend the use
of recycled engine coolant in vehicles originally
equipped with Motorcraft Premium Gold Engine
Coolant since a Ford-approved recycling process is
not yet available.
Used engine coolant should be disposed of in
an appropriate manner. Follow your community's
regulations and standards for recycling and disposing
of automotive fluids.
Maintenance and care
164

Coolant refill capacity
To find out how much fluid your vehicle's cooling
system can hold, refer toRefill capacitiesin the
Capacities and specificationschapter.
Fill your engine coolant reservoir as outlined in
Adding engine coolantin this chapter.
Severe climates
If you drive in extremely cold climates (less than
±36É C [±34É F]):
²it may be necessary to increase the coolant
concentration above 50%.
²NEVER increase the coolant concentration
above 60%.
²increased engine coolant concentrations
above 60% will decrease the overheat
protection characteristics of the engine
coolant and may cause engine damage.
²refer to the chart on the coolant container
to ensure the coolant concentration in your
vehicle will provide adequate freeze
protection at the temperatures in which you
drive in the winter months.
If you drive in extremely hot climates:
²it is still necessary to maintain the coolant
concentration above 40%.
²NEVER decrease the coolant concentration
below 40%.
²decreased engine coolant concentrations
below 40% will decrease the corrosion
protection characteristics of the engine
coolant and may cause engine damage.
²decreased engine coolant concentrations
below 40% will decrease the freeze
protection characteristics of the engine
coolant and may cause engine damage.
Maintenance and care
165

²refer to the chart on the coolant container
to ensure the coolant concentration in your
vehicle will provide adequate protection at
the temperatures in which you drive.
Vehicles driven year-round in non-extreme climates
should use a 50/50 mixture of engine coolant and
distilled water for optimum cooling system and
engine protection.
CHECKING AND ADDING POWER STEERING
FLUID
Check the power steering fluid. Refer to the
scheduled maintenance guide for the service interval
schedules. If adding fluid is necessary, use only
MERCONtAT F.
If your vehicle is
equipped with the
3.8L V6 engine,check
the power steering
fluid level with the
engine at normal
operating temperature.
1. Start the engine and
let it run until it
reaches normal
operating temperature
(the engine coolant
temperature gauge
indicator will be near
the center of the
normal area between H
and C).
2. While the engine idles, turn the steering wheel
left and right several times.
3. Turn the engine off.
4. Check the fluid level on the dipstick. It should be
within the FULL HOT range. Do not add fluid if the
level is within this range.
FILL
HOT
Maintenance and care
166

MOTORCRAFT PART NUMBERS
Component 3.8L OHV V6 engine 4.6L SOHC V8 engine
Air filter element FA-1611 FA-1634
Fuel filter FG-986 FG-986B
Battery BXT-59 BXT-59
Oil filter FL-400S FL-820S
PCV valve EV-152 EV-98
Spark plugs* AWSF-42EE** AWSF-32P
* Refer to Vehicle Emissions Control Information (VECI)
decal for spark plug gap information.
**If a spark plug is removed for inspection, it must be
reinstalled in the same cylinder. If a spark plug needs to
be replaced, use only spark plugs with the same service
part number suffix letter as shown on the engine decal.
REFILL CAPACITIES
Fluid Ford Part Name Application Capacity
Brake fluid High Performance
DOT 3 Motor
Vehicle Brake
FluidAll Fill to line on
reservoir
Engine oil
(includes filter
change)Motorcraft SAE
5W-20 Super
Premium Motor
OilAll 4.7L (5.0 quarts)
Engine coolant
1Motorcraft
Premium Engine
Coolant
(green-colored)
orMotorcraft
Premium Gold
Engine Coolant
(yellow-colored)3.8L OHV V6
engine11.2L (11.8
quarts)
4.6L SOHC V8
engine13.3L (14.1
quarts)
Power steering
fluidMotorcraft
MERCONtAT F3.8L OHV V6
engineKeep in FULL
HOT range on
dispstick
4.6L SOHC V8
engineFill to between
MIN and MAX
lines on reservoir
Capacities and specifications
206

Fluid Ford Part Name Application Capacity
Rear axle
lubricant
2Motorcraft SAE
80W-90 Premium
Rear Axle
Lubricant7 .5 inch axle 1.5L (3.25 pints)
Motorcraft SAE
75W-140
Synthetic Rear
Axle Lubricant8.8 inch axle 2.0L (4.25 pints)
Fuel tank N/A All 59.4L (15.7
gallons)
Transmission fluid
3Motorcraft
MERCONtVATFAutomatic with
3.8L OHV V6
engine13.1L (13.9
quarts)4
Automatic with
4.6L SOHC V8
engine12.0L (12.8
quarts)4
Motorcraft
MERCONtAT FManual with 3.8L
OHV V6 engine2.6L (5.6 pints)5
Mobil 1
SynthetictAT FManual with 4.6L
SOHC V8 engine3.8L (8.0 pints)5
Windshield
washer fluidUltra-Clear
Windshield
Washer
ConcentrateAll 3.8L (4.0 quarts)
1Add the coolant type originally equipped in your vehicle.2Rear axle lubricants do not need to be checked or
changed unless a leak is suspected, service is required or
the axle assembly has been submerged in water. The axle
lubricant should be changed any time the rear axle has
been submerged in water. Fill 6 mm to 14 mm (1/4 inch to
9/16 inch) below bottom of fill hole. Add 118 ml (4 oz.) of
Additive Friction Modifier C8AZ-19B546-A or equivalent
meeting Ford specification EST-M2C118±A for complete
refill of Traction-Lok axles.
3Ensure the correct automatic transmission fluid is used.
Transmission fluid requirements are indicated on the
dipstick or on the dipstick handle. MERCONtand
MERCONtV are not interchangeable. DO NOT mix
MERCONtand MERCONtV. Refer to your scheduled
maintenance guide to determine the correct service
interval.
4Indicates only approximate dry-fill capacity. Some
applications may vary based on cooler size and if equipped
with an in-tank cooler. The amount of transmission fluid
and fluid level should be set by the indication on the
dipstick's normal operating range.
Capacities and specifications
207

5Service refill capacity is determined by filling the
transmission to the bottom of the filler hole with the
vehicle on a level surface.
LUBRICANT SPECIFICATIONS
Item Ford part name Ford part
numberFord
specification
Brake fluid High Performance
DOT 3 Motor
Vehicle Brake
FluidC6AZ-19542-AB ESA-M6C25-A
and DOT 3
Door
weatherstripsSilicone Lubricant F7AZ-19G208-BA
and
F5AZ-19553-AAESR-M13P4-A
Door latch, hood
latch, auxiliary
hood latch, door
hinges, striker
plates, seat tracks
and fuel filler
door hingeMulti-Purpose
GreaseD0AZ-19584-AA
or
F5AZ-19G209-AAESB-M1C93-B or
ESR-M1C159-A
Engine coolant Motorcraft
Premium Engine
Coolant
(green-colored)VC-4±A (US) or
CXC-10 (Canada)ESE-M97B44-A
Motorcraft
Premium Gold
Engine Coolant
(yellow-colored)VC-7±A WSS-M97B51±A1
Engine oil Motorcraft SAE
5W-20 Super
Premium Motor
OilXO-5W20-QSP WSS-M2C153-H
with API
Certification Mark
Lock cylinders Penetrating and
Lock LubricantMotorcraft XL-1 none
Power steering
fluid and
convertible top
fluid (if
equipped)Motorcraft
MERCONtAT FXT-2-QM MERCONt
Rear Axle
LubricantMotorcraft SAE
80W-90 Premium
Rear Axle
Lubricant
1
XY-80W90-QL WSP-M2C197-A
Motorcraft SAE
75W-140
Synthetic Rear
Axle LubricantXY-75W140-QL WSP-M2C192-A
Capacities and specifications
208

A
Air bag supplemental
restraint system ........ 88
and child safety
seats ......................... 90
description .............. 88
disposal .................... 93
driver air bag .......... 91
indicator light ..... 9, 92
operation ................. 91
passenger air bag ... 91
Air cleaner filter ..... 206
Air conditioning ........ 20
manual heating and air
conditioning
system ..................... 20
Antifreeze (see Engine
coolant) ................... 157
Anti-lock brake system
(see Brakes) .... 108±109
Anti-theft system
warning light ............. 9
Audio system (see
Radio) ........................ 24
Automatic
transmission ............ 113
driving an automatic
overdrive ............... 115
fluid, adding .......... 167
fluid, checking ...... 167
fluid, refill
capacities ............... 206
fluid,
specification .......... 209
Auxiliary power
point ........................... 60Axle
lubricant
specifications. 208±209
refill capacities ...... 206
traction lok ............ 122
B
Battery ..................... 171
acid, treating
emergencies .......... 171
charging system
warning light ............. 9
jumping a disabled
battery ................... 141
maintenance-free .. 171
replacement,
specifications ........ 206
servicing ................ 171
voltage gauge .......... 17
Belt minder ............... 83
Brakes .............. 108, 110
anti-lock ......... 108±109
anti-lock brake
system (ABS) warning
light .................. 12, 109
brake warning
light .......................... 13
fluid, checking and
adding .................... 155
fluid, refill
capacities ............... 206
fluid,
specifications 208±209
lubricant
specifications 208±209
parking .................. 110
shift interlock ........ 113
Break-in period ........... 3
Index
228

C
Capacities for refilling
fluids ........................ 206
Cassette tape
player ......................... 34
Certification Label .. 211
Child safety
restraints ................... 94
child safety belts .... 94
Child safety seats ...... 95
attaching with tether
straps ....................... 99
in front seat ............ 97
in rear seat .............. 97
Cleaning your
vehicle ...................... 199
engine
compartment ......... 202
exterior .................. 200
exterior lamps ....... 201
instrument
cluster lens ............ 204
instrument panel .. 204
interior ........... 204±205
mirrors ................... 201
plastic parts .......... 201
safety belts ............ 204
washing .................. 199
waxing ................... 200
wheels .................... 201
windows ................ 204
wiper blades .......... 202
Climate control (see Air
conditioning or
Heating) ..................... 20
Clock .................... 33, 47
Clutch
adjusting ................ 156operation while
driving ................... 119
recommended shift
speeds .................... 120
Console ...................... 59
Controls
power seat ............... 74
Convertible ................ 61
cleaning ................. 202
installation of the
boot .......................... 62
lowering the
convertible top ........ 61
raising the convertible
top ............................ 63
Coolant
checking and
adding .................... 157
refill
capacities ....... 165, 206
specifications. 208±209
Cruise control (see
Speed control) .......... 53
Customer
Assistance ................ 129
Ford accessories for
your vehicle .......... 221
Ford Extended Service
Plan ........................ 212
Getting assistance
outside the U.S. and
Canada ................... 220
Getting roadside
assistance .............. 129
Getting the service
you need ............... 213
Ordering additional
owner's
literature ............... 225
Index
229