refrigerant type FORD MUSTANG 2003 User Guide

The spring lock coupling is a refrigerant line coupling held together by a garter spring inside a circular
cage.
zWhen the coupling is connected together, the flared end of the female fitting slips behind the
garter spring inside the cage of the male fitting.
z The garter spring and cage then prevent the flared end of the female fitting from pulling out of
the cage.
z Three O- ring seals are used to seal between the two halves of the A/C condenser core
couplings. All other couplings have two O- ring seals.
z Use only the O- ring seals listed in the Ford Master Parts Catalog for the spring lock coupling.
z A plastic indicator ring is used on the spring lock couplings of the A/C evaporator core to
indicate, during vehicle assembly, that the coupling is connected. Once the coupling is
connected, the indicator ring is no longer necessary but will remain captive by the coupling near
the cage opening.
z The indicator ring may also be used during repair operations to indicate connection of the
coupling.
z An A/C tube lock coupling clip (19E746) may be used to secure the coupling but is not required.
Service Gauge Port Valves
The high- pressure service gauge port valve is located on the A/C manifold and tube.
The low pressure service gauge port valve is located on the suction accumulator. 2 — Female fitting (part of 19860)
3 19E746 A/C tube lock coupling clip
4 19E576 A/C tube lock coupling spring
5 — Cage (part of 19D690)
6 — O-
ring seals (part of 19D690) 7 — Male fitting (part of 19835)
Item Part
Number Description
1 19D702 A/C charging valve cap
2 19D701 Low pressure service gauge port valve (part of
19C836)
3 19D701 Schrader-
type valve 4 — O-
ring seal (part of 19D701) 5 19D701 High pressure service gauge port valve (part of Klj . 9 ba
102003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

The fitting is an integral part of the refrigeration line or component.
zSpecial couplings are required for both the high side and low side service gauge ports.
z A new Schrader- type valve core can be installed if the seal leaks.
z Always install the A/C charging valve cap (19D702) on the service gauge port valves after
repairing the refrigerant system. 19D734)
6 19D702 A/C charging valve cap Klj . 10 ba
102003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Condenser Core
Removal and Installation
NOTE:
If an A/C condenser core leak is suspected, the A/C condenser core must be leak tested
before it is removed from the vehicle. For additional information, refer to Section 412 - 00 .
NOTE: Installation of a new suction accumulator is not required when repairing the air conditioning
system except when there is physical evidence of contamination from a failed A/C compressor or
damage to the suction accumulator.
All vehicles
1. Recover the refrigerant. For additional information, refer to Section 412 - 00 .
2. Remove the pin- type retainers and remove the upper radiator sight shield.
3. Remove the air cleaner and air cleaner outlet tube. For additional information, refer to Section 303 - 12 .
4.6L (2V), 4.6L (4V) vehicles 4. Remove the bolts and position the coolant bottle aside.
SECTION 412-
03: Air Conditioning 2003 Mustang Workshop Manual Material
Item Specification
PAG Refrigerant Compressor
Oil (R-
134a Systems)
F7AZ- 19589- DA (Motorcraft YN-
12- C) WSH-
M1C231-
B Klj . 1 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Condenser to Evaporator Line
Removal and Installation
NOTE:
Installation of a new suction accumulator is not required when repairing the air conditioning
system except when there is physical evidence of contamination from a failed A/C compressor or
damage to the suction accumulator.
1. Recover the refrigerant. For additional information, refer to Section 412 - 00 .
2. Remove the air cleaner outlet tube. For additional information, refer to Section 303 - 12 .
3. Raise the vehicle. For additional information, refer to Section 100 - 02 .
4. Remove the line bracket pin- type retainer.
5. Lower the vehicle.
6. Remove the nut and disconnect the fitting at the condenser. zDiscard the O- ring seal.
SECTION 412-
03: Air Conditioning 2003 Mustang Workshop Manual Material
Item Specification
PAG Refrigerant Compressor
Oil (R-
134a Systems)
F7AZ- 19589- DA (Motorcraft YN-
12- C) WSH-
M1C231-
B Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...