wire clip FORD MUSTANG 2003 Workshop Manual

REMOVAL AND INSTALLATION
Spindle
Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number or an equivalent part must be installed, if installation is necessary. Do
not use a part of lesser quality or substitute design. Torque values must be used as specified
during reassembly to ensure correct retention of these parts.
1. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
2. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
3. Remove the front wheel hub (1104). For additional information, refer to Wheel Hub and Bearing in this section.
4. Remove the bolt and the ABS sensor.
5. Unclip the ABS sensor wire from the bracket.
SECTION 204-
01: Front Suspension 2003 Mustang Workshop Manual Special Tool(s)
Tie-
Rod End Remover
211- 001 (TOOL- 3290-D) or
Equivalent Klj . 1 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Shock Absorber
Removal
WARNING: All vehicles are equipped with gas pressurized shock absorbers which will
extend unassisted. Do not apply heat or flame to the shock absorbers during removal or
component servicing. Failure to follow these instructions can result in personal injury.
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number or an equivalent part must be installed, if installation is necessary. Do
not use a part of lesser quality or substitute design. Torque values must be used as specified
during reassembly to ensure proper retention of these parts.
1. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
2. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
3. Remove the front brake disc. For additional information, refer to Section 206 - 03 .
4. Remove the bolt and the ABS sensor.
5. Unclip the ABS sensor wire from the bracket.
6. Remove the nut and the ABS sensor wire bracket.
SECTION 204-
01: Front Suspension 2003 Mustang Workshop Manual Klj . 1 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

12. Unclip the ABS sensor wires from the subframe.
13. Support the lower suspension arm and bushings (5A649) with jack stands.
14. Remove the nuts, bolts and disconnect the shock absorbers (18125) from the lower suspension
arm and bushings. Discard the bolts and nuts.
15. Lower the lower suspension arm and bushings and remove the jack stands.
16. Support the rear subframe using the special tool 014- 00765.
17. Remove and discard the nuts from the subframe front bolts. Klj . 3 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. Remove the special tool 014-
00765.
7. Support the lower suspension arm and bushings with jack stands.
8. CAUTION: Make sure the hardened washer is installed between the lower
suspension arm and bushing and the shock absorber. Failure to do so can result in
damage and failure of the lower suspension arm and bushing.
Connect the shock absorbers to the lower suspension arm and bushing and install new bolts
and nuts.
9. Clip the ABS sensor wires to the subframe.
10. Install the ABS sensors and the bolts. Klj . 6 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

NOTE:
All fasteners are important because they can affect the performance of vital parts and systems.
Incorrect installation of the fasteners can result in major repair expenses. They must be installed new
with fasteners of the same part number if installation becomes necessary. Do not install a new part of
lesser quality or substitute a design. Torque values must be used as specified during assembly to
make sure these parts function correctly.
The body of the steering column (3C529) is made of magnesium die castings. The steering column is
attached to a support that is an integral part of the instrument panel. The lower attachments of the
steering column are through a bracket that bends during collapse. The upper attachments are through
plastic shear modules that separate from the main casting during collapse. A clip and washer are
attached to the shear modules to reduce steering column shake and to assist in installation of the
steering column. 45 N621906 Nut
46 N803942 Bolt
47 3A525 Intermediate shaft coupling
48 11A128 Ignition key warning switch terminal
49 N806583 Bearing housing retaining screw
50 N804865-
S58 Screw
51 14A06 Wire connector bracket
52 3E715 Lock lever lower actuator
53 3E691 Lock pawl
54 3F723 Actuator housing
55 3E745 Lock actuator cover
56 3F719 Ignition/shifter interlock cable
57 N808124-
58M Screw
58 3D655 Position spring
59 3D656 Tilt flange bumper
60 N806582 Tilt pivot screws
61 11582 Ignition switch lock cylinder
62 3E700 Lock housing bearing
63 3E717 Lock gear
64 3530 Upper shroud
65 3511 Lock cylinder housing
66 N805857 Lock actuator lever pin
67 3D681 Bearing retainer Klj . 3 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

5. Disconnect the electrical connector.
6.
CAUTION: Extra force may be needed to lift up on the handle. Do not to pull too far
or damage to the overdrive cancel button may result, as the wires may be pulled out of
the switch.
Remove the screw and the handle.
7. Remove the clip and bolt from the brake shift interlock cable. Klj . 2 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

5. Disconnect the TCS connector.
6.
CAUTION: Extra force may be needed to lift up on the handle. Do not to pull too far
or damage to the overdrive cancel button may result, as the wires may be pulled out of
the switch.
Remove the screw and the handle.
7. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
8. Disconnect the shift cable and discard the plastic clip. Klj . 2 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Disc and Pressure Plate —
4.6L (4V) Engine
1. Disconnect the battery ground cable. For additional information, refer to Section 414 - 01 .
2. Remove the transmission. For additional information, refer to Section 308 - 03C .
3. Remove the starter. 1. Remove the terminal cap.
2. Remove the nuts.
3. Remove the wires and position them aside.
4. Remove the two bolts and the starter.
4. Remove the clutch cable clip, then pull the cable through the clutch housing.
SECTION 308-
01: Clutch 2003 Mustang Workshop Manual Special Tool(s)
Clutch Aligner
308-
020 (T74P-7137- K)
Material Item Specification
Premium Long Life Grease
XG
-1-C ESA-
M1C75- B Klj . 1 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

6. Remove the heater air damper door motor.
1. Disconnect the vacuum lines.
2. Loosen the nuts and unclip the motor.
7. Release the vacuum harness from the housing.
8. Remove the screws and remove the resistor.
9. Disconnect the jumper wire. Klj . 2 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

13. Remove the wire harness from its holders.
14. Remove the clockspring.
1. Pry the clockspring retaining clips loose.
2. Remove the clockspring.
Installation WARNING: To reduce the risk of serious personal injury, read and follow all warnings,
cautions and notes at the beginning of the removal procedure.
Vehicles receiving a new clockspring
1. NOTE: A new clockspring is supplied in a centralized position and held there with a key.
Remove the key from the clockspring, holding the rotor in its centralized position. zDo not allow the clockspring rotor to turn. Vehicles needing clockspring recentering Klj . 5 ba
112003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...