wheel torque FORD MUSTANG 2010 5.G Shelby GT500 Supplement Manual

Introduction
2
Shelby GT500 unique features
4
Driving your Shelby GT500
8
Alternate calibration 8
Transmission operation 8
AdvanceTrac
9
Driving through water 9
Ground clearance 10
Washing your vehicle 10
Tire information
11
Wheel lug nut torque 12
Roadside Emergencies
16
Wrecker towing 16
Maintenance and Specifications
20
Engine oil 21
Air filter(s) 25
Part numbers 26
Refill capacities 27
Warranty coverage
32
All rights reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage and retrieval
system or translation in whole or part is not permitted without written
authorization from Ford Motor Company. Ford may change the contents without
notice and without incurring obligation.
Copyright © 2009 Ford Motor Company
Table of Contents
1
2010 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)

UNIQUE FEATURES
•5.4L DOHC 32V Supercharged V-8 engine with intercooler — 540
horsepower @ 6,200 rpm, 510 lb-ft torque @ 4,500 rpm SAE certified
•Low-restriction, cold air intake system
•SVT tuned exhaust system with X pipe and 4 inch tips
•Engine oil cooler
•TR-6060 6 speed manual transmission
•Twin disc clutch
•Anti-lock brake system
•High performance brake pads
•Front Brakes: Brembo 14 inch vented disc with four piston aluminum
calipers
•Rear brakes include unique friction material
•SVT tuned front and rear suspension
•18 in x 9.5 in cast aluminum wheels (convertible only)
•19 in x 9.5 in forged aluminum wheels (coupe only)
•P255/45ZR-18 front, P285/40ZR-18 rear (convertible only) Goodyear
F1 tires
•P255/40ZR-19 front, P285/35ZR-19 rear (coupe only) Goodyear F1
tires
•Unique front fascia, rear fascia, aerodynamically tuned front splitter,
fog lamps, hood with functional air extractors, rear decklid spoiler
Shelby GT500 unique features
4
2010 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)

SUSPENSION
•MacPherson strut with L-arm front suspension
•8.8 inch solid rear axle with limited slip differential (3.55:1 ratio)
Coupe stabilizer bars:
•34 x 5.1 mm tubular front stabilizer bar
•24 mm solid rear bar
•Tokico twin tube shocks and struts
Convertible stabilizer bars:
•34 x 5.1 mm tubular front stabilizer bar
•20 mm solid rear bar
•Tokico twin tube shocks and struts
Spring rates:
•39.0 N/mm front and 31.5 N/mm rear (Coupe)
•30.9 N/mm front and 23.0 N/mm rear (Convertible)
WHEELS
Your SVT vehicle is equipped with unique wheels matched to the tires.
These wheels are more susceptible to damage due to their diameter,
width and low profile tires. To avoid damage to your wheels:
•Maintain proper tire pressure (seeTiresin this supplement).
•Do not drive your vehicle through an automated, commercial car wash
due to the vehicle’s low ground clearance, tire width and track. Wash
your vehicle by hand, or by using a touchless commercial wash with
no mechanical tracks on the floor. Do not use a commercial or high
pressure wand on the striped surfaces.
•When installing wheels, always torque lug nuts to specification with a
torque wrench.
•Inspect your wheels for damage on a regular basis. If a wheel is
damaged, replace it immediately.
•In the event that you encounter an abnormally harsh impact, inspect
the outer diameter of your wheels, both inside and out, for damage.
Tire information
11
2010 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)

Operating at high speeds
Your SVT vehicle is capable of high speeds and is equipped with tires
rated for the vehicle’s maximum speed, electronically limited to 155 mph
(250 km/h). Remember to drive safely, obey all traffic laws and only
operate your SVT vehicle at high speeds at locations equipped and
designed to do so safely. Before operating your vehicle at high speeds:
•Ensure correct tire pressures (seeTiresin this supplement).
•Inspect wheels and tires for wear and damage. Replace any damaged
wheels or tires.
•Do not operate your vehicle at high speeds with more than two
passengers or while carrying cargo.
Wheel lug nut torque specifications
Retighten the lug nuts to the specified torque at 500 miles (800 km)
after any wheel disturbance (tire rotation, changing a flat tire, wheel
removal, etc.).
Bolt size Wheel lug nut torque*
lb.ft. N•m
12x 20 100 135
* Torque specifications are for nut and bolt threads free of dirt and
rust. Use only Ford recommended replacement fasteners.
WARNING:When a wheel is installed, always remove any
corrosion, dirt or foreign materials present on the mounting
surfaces of the wheel or the surface of the wheel hub, brake drum or
brake disc that contacts the wheel. Ensure that any fasteners that
attach the rotor to the hub are secured so they do not interfere with
the mounting surfaces of the wheel. Installing wheels without correct
metal-to-metal contact at the wheel mounting surfaces can cause the
wheel nuts to loosen and the wheel to come off while the vehicle is in
motion, resulting in loss of control.
Tire information
12
2010 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)