oil change FORD MUSTANG 2012 5.G Boss 302 Supplement Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 2012, Model line: MUSTANG, Model: FORD MUSTANG 2012 5.GPages: 40, PDF Size: 0.33 MB
Page 21 of 40
SUSPENSION
•MacPherson strut with L-arm front suspension
•8.8 inch solid rear axle with limited slip differential (3.73:1 ratio)
Boss302:
•34.6 x 4.4 mm tubular front stabilizer bar
•25.0 mm solid rear stabilizer bar
•Tokico twin tube adjustable shocks and struts
•26.0 N/mm front and 32.4 N/mm rear coil springs
Boss302 with Laguna Seca package:
•34.6 x 4.4 mm tubular front stabilizer bar
•26.0 mm solid rear stabilizer bar
•Tokico twin tube adjustable shocks and struts
•24.0 N/mm front and 33.5 N/mm rear coil springs
ADJUSTABLE SUSPENSION DAMPERS
Your vehicle has adjustable
suspension dampers. The
adjustment controls are located on
top of the damping rods and can be
adjusted with a small screwdriver.
Remove the cap to access the
control for the front strut.
To access the rear shock, pull the
carpet back in the trunk area. Then,
lift the trim panel and pull rearward
to expose the adjustable suspension
damper.
Position (1) has the lowest damping
force which provides for a more
comfortable ride. Position (5) has
the highest damping force which
provides more responsive handling.
Position (2) is the factory setting
(shown in graphic).
Left and right dampers should always be set to the same dial position.
Front and rear can be adjusted independently to change vehicle response.
1
2
3
4
5
Chassis
21
2012 05+ Mustang(197)
Supplement, 2nd Printing
USA(fus)
Page 31 of 40
MOTORCRAFT PART NUMBERS
Component Boss 302 engine
Engine drivebelt JK6-678
Lightweight battery BXT-96R-500
ENGINE OIL RECOMMENDATION
Use MotorcraftSAE 5W-50 full synthetic or an equivalent SAE 5W-50
full synthetic oil meeting Ford specification WSS-M2C931-B.
Do not use supplemental engine oil additives, cleaners or other engine
treatments. They are unnecessary and could lead to engine damage that
is not covered by Ford warranty.
Change your engine oil and filter according to the appropriate schedule
listed in thescheduled maintenance information.
Maintenance and Specifications
31
2012 05+ Mustang(197)
Supplement, 2nd Printing
USA(fus)
Page 32 of 40
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES
Item CapacityFord part name or
equivalentFord part number /
Ford Specification
Brake fluidBetween MIN and
MAX lines on
reservoirMotorcraftHigh
Performance DOT 3
Motor Vehicle Brake
FluidPM-1-C /
WSS-M6C62-A or
WSS-M6C65-A1
Engine oil (includes
filter change)8.5 quarts (8.0L)Motorcraft5W-50 Full
Synthetic Motor OilX0-5W50-QGT /
WSS-M2C931-B
Engine coolant
1
15.2 quarts
(14.4L)MotorcraftSpecialty
Orange Engine Coolant
with bittering agent (US)
/
MotorcraftSpecialty
Orange Engine Coolant
(Canada)VC-3-B (US)
CVC-3-B (Canada) /
WSS-M97B44-D
Rear axle lubricant
2
5.0 pints
(2.4L)MotorcraftSAE
75W-140 High
Performance Synthetic
Rear Axle LubricantXY-75W140-QL /
WSL-M2C192–A
Rear axle fluid friction
modifier5oz
(148ml)Additive Friction
ModifierXL-3
EST-M2C118-A
Fuel tank16.0 gallons
(60.5L)——
Maintenance and Specifications
32
2012 05+ Mustang(197)
Supplement, 2nd Printing
USA(fus)
Page 37 of 40
TRACK PREPARATION
The Boss302 and Boss302 Laguna Seca edition have been rigorously
proven out on race tracks. Below are recommendations for optimizing
your Boss302 for a track day event.
•For optimal performance, premium fuel is recommended.
•
Change brake fluid to Super DOT 4 to improve track performance of
braking system (WSS-M6C65-A2), Ford part number (YS4Z-19542-AA).
•Install Ford Racing front brake cooling kit (M-2004-MB) to improve
brake cooling (standard on Laguna Seca edition).
•Remove rear brake dust shields to improve brake cooling.
•Install Ford Racing transmission cooling scoop (M-5025-MBR) to
improve transmission cooling (standard on Laguna Seca edition).
•During extended track sessions in extreme temperatures or
conditions, your Boss 302 may require additional engine cooling
actions. If the water temperature warning light illuminates, return to
the paddock and let the vehicle return to normal operating
temperature while idling before turning the engine off. Prior to the
next session, remove your Boss 302’s upper grille from the front
fascia. This will allow more cooling air to the radiator and allow the
car to run extended sessions in extreme heat. Visit fordracing.com for
additional parts to further enhance the powertrain cooling on your
Boss 302.
•For extended track use, Ford recommends installing a rear differential
cooler to improve rear axle cooling.
•Remove vertical rear tire spoilers at rear edge of rocker moldings.
•The Ford Racing front splitter kit (M-16601-MB, standard on Laguna
Seca edition) can be installed to improve high-speed vehicle stability
and handling. If the Ford Racing front splitter kit will be installed on a
Boss 302 without the Laguna Seca package, Ford recommends
installing the Laguna Seca edition rear spoiler in place of the standard
rear spoiler to maintain aerodynamic balance. This front splitter is
intended for race track use only and is not legal for on-street driving.
It may degrade crash performance and void the vehicle warranty. The
front splitter must be installed by the customer.
Track Use Preparation
37
2012 05+ Mustang(197)
Supplement, 2nd Printing
USA(fus)
Page 40 of 40
WARRANTY COVERAGE
The Boss302 carries the same warranty as other Ford Mustang models.
This information is covered in its entirety in the Ford Motor Company
Warranty Guide.
The three unique Laguna Seca Package high performance parts (front
splitter, front brake cooling kit, and transmission cooling scoop) are
intended for track use and have no warranty coverage.
Warranty service for the Boss302 can be obtained at any Ford dealer
nationwide.
Ford does not recommend modifying or racing Ford vehicles, as they are
designed and built to be driven as delivered from the factory. The Ford
Motor Company Warranty Guide discusses vehicle usage and the
installation of aftermarket parts and their effect on warranty coverage.
Please see the Warranty Guide for complete information.
In the event the vehicle is intended for track use, and the loss of
warranty coverage is not of concern, the following vehicle durability
modification is required:
•Ford recommends that you change your axle lubricant and
friction modifier after the initial (first) hour of high-speed
operation or if the vehicle is subjected to track or competition
conditions; thereafter changing the axle lubricant and friction
modifier every 12 hours (under these conditions).
•Ford recommends you change your oil and filter after your
vehicle is subjected to track and/or competition conditions.
Additionally, perform multi-point inspection and the maintenance
outlined in the 150,000 mile (240,000 km) normal maintenance schedule
of thescheduled maintenance informationafter track use. Refer to
the vehicle service manual for removal and installation procedures.
Replace with Genuine Ford and Motorcraftservice parts as needed.
These modifications may not necessarily protect your engine from
damage in competition conditions. Subjecting your vehicle to competition
conditions even with these proposed modifications may render repairs
non-reimbursable under the warranty.
Warranty Coverage
40
2012 05+ Mustang(197)
Supplement, 2nd Printing
USA(fus)