tire type FORD MUSTANG 2022 Warranty Guide

WARNING: To reduce the risk of
personal injury, make sure the engine is
cool before unscrewing the coolant
pressure relief cap. The cooling system
is under pressure. Steam and hot liquid
can come out forcefully when you loosen
the cap slightly. WARNING:
Do not add coolant
further than the MAX mark.
Note: Do not use stop leak pellets, cooling
system sealants, or additives as they can
cause damage to the engine cooling or
heating systems. Your vehicle warranty
would not cover this damage.
• DO NOT MIX different colors or types
of coolant in your vehicle. Make sure
you use the correct coolant. Mixing of
engine coolants could harm your
engine ’s cooling system. The use of an
improper coolant could harm engine
and cooling system components and
could void the warranty.
• In case of emergency, you can add a
large amount of water without engine
coolant, in order to reach a vehicle
service location. In this instance, drain
the cooling system, chemically clean
the system with Motorcraft® Premium
Cooling System Flush, and refill with
prediluted coolant as soon as possible.
Water alone without engine coolant
can cause engine damage from
corrosion, overheating or freezing.
Note: Do not use alcohol, methanol or brine
or any engine coolants mixed with alcohol
or methanol antifreeze coolant. Alcohol and
other liquids can cause engine damage from
overheating or freezing.
Note: Do not add extra inhibitors or
additives to the coolant. These can be
harmful and compromise the corrosion
protection of the engine coolant. Unscrew the cap slowly. Any pressure
could escape as you unscrew the cap.
Add prediluted engine coolant meeting our
specification. See the Capacities and
Specifications chapter of the Owner's
Manual for more information. Whenever
you add coolant, check the coolant level
in the coolant reservoir the next few times
you drive the vehicle. If necessary, add
enough prediluted coolant to bring the
coolant level to the proper level.
Coolant Refill Procedure
Use the following procedure when refilling
the cooling system after it has been
drained or become extremely low.
1. Remove the pressure relief cap from
the coolant reservoir as previously
outlined.
2. Slowly add prediluted coolant to the coolant reservoir until the coolant level
is between the
MIN and MAX marks
on the reservoir.
3. Reinstall the pressure relief cap.
4. Start and idle the engine until the upper
radiator hose is warm, which indicates
the thermostat is open and coolant is
flowing through the entire system.
5. Shut the engine off and let it cool.
6. Remove the pressure relief cap from the coolant reservoir as previously
outlined.
7. Add prediluted coolant to the coolant reservoir until the coolant level is
between the
MIN and MAX marks on
the reservoir.
8. Reinstall the pressure relief cap.
9. Check the coolant level in the reservoir
before you drive your vehicle the next
few times with the engine cool.
41
2022 Mustang (CZG) Mach 1, enUSA, Edition date: 202110, First-Printing Maintenance

Start Option
Allows you to select the type of countdown
the information display shows before
starting an event.
Status Screen
Provides the status of your chosen
performance-related settings.
View/Clear Results
Allows you to view and clear the last and
saved results of the Acceleration Timer,
Brake Performance, and All Time Best
results.
Road Course Alignment
Recommendations
Note:
After your track day is complete,
return your car to the street alignment and
tire pressures.
Note: Using these wheel alignment settings
may cause excessive tire wear. Only use
these settings for racing or competitive
driving. Excessive tire wear is not covered
under the vehicle warranty.
If you plan to participate in road course
track days, we recommend the following
chassis settings for optimal tire wear and
handling performance.
All settings are at curb loading condition
full of fuel.
Mach 1 Street
Track
Front
-1.03°
-1.5°
Camber
0°
0°
Toe - Total Street
Track
Rear
-1.5°
-1.5°
Camber
0.24°
0.24°
Toe - Total
Mach 1 with Handling Package Street
Track
Front
-1.21°
-2.25°
Camber
0.1°
0.1°
Toe - Total Street
Track
Rear
-1.14°
-1.5°
Camber
0.3°
0.3°
Toe - Total
46
2022 Mustang (CZG) Mach 1, enUSA, Edition date: 202110, First-Printing Track Use

WHEELS
Your vehicle has unique wheels matched
to the tires. These wheels are more
susceptible to damage due to their
diameter, width and low profile tires.
To avoid damage to your wheels:
•
Maintain proper tire pressure (see Tires
in this supplement).
• When installing wheels, always torque
lug nuts to specification with a torque
wrench.
• Inspect your wheels for damage on a
regular basis. If a wheel is damaged,
replace it immediately.
• In the event that you encounter an
abnormally harsh impact, inspect the
outer diameter of your wheels, both
inside and out, for damage.
Use Motorcraft™ Wheel and Tire Cleaner
to maintain your wheels. See your Owner ’s
Manual for information on other cleaning
products and vehicle care. Wheel Lug Nut Torque
Specifications WARNING: When you install a
wheel, always remove any corrosion, dirt
or foreign materials present on the
mounting surfaces of the wheel or the
surface of the wheel hub, brake drum or
brake disc that contacts the wheel. Make
sure to secure any fasteners that attach
the rotor to the hub so they do not
interfere with the mounting surfaces of
the wheel. Installing wheels without
correct metal-to-metal contact at the
wheel mounting surfaces can cause the
wheel nuts to loosen and the wheel to
come off while your vehicle is in motion,
resulting in loss of vehicle control,
personal injury or death.
Retighten the lug nuts to the specified
torque at
500 mi (800 km) after any
wheel disturbance (tire rotation, changing
a flat tire or wheel removal). lb-ft (Nm)*
Bolt Size
150 ± 15 (200 ± 20)
M14 x 1.5
*Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford
recommended replacement fasteners.
TIRES WARNING:
Only use replacement
tires and wheels that are the same size,
load index, speed rating and type (such
as P-metric versus LT-metric or
all-season versus all-terrain) as those
originally provided by Ford. The
recommended tire and wheel size may
be found on either the Safety
Compliance Certification Label (affixed to either the door hinge pillar, door-latch
post, or the door edge that meets the
door-latch post, next to the driver's
seating position), or the Tire Label which
is located on the B-Pillar or edge of the
driver's door. If this information is not
found on these labels, then you should
contact your authorized dealer as soon
52
2022 Mustang (CZG) Mach 1, enUSA, Edition date: 202110, First-Printing Wheels and Tires

as possible. Use of any tire or wheel not
recommended by Ford can affect the
safety and performance of your vehicle,
which could result in an increased risk of
loss of vehicle control, vehicle rollover,
personal injury and death.
Note: Do not use tire chains on your vehicle.
The use of any type of tire chain on these
tires could damage your vehicle. Your vehicle comes with low profile, high
performance tires designed to optimize
the driving dynamics you expect in a Ford
Performance vehicle. These tires are not
optimized for off-road or winter, snow or
cold weather, performance, and their ride,
noise and wear characteristics are different
than non-performance tires. Also, because
of their lower profile, the tires are more
susceptible to damage due to potholes
and rough roads. Wheels (Inches)
Tires
Variant
19 x 9.5
255/40R19
Front
Mach 1
19 x 10
275/40R19
Rear
19 x 10.5
305/30R19
Front
Mach 1 with handling
package
19 x 11
315/30R19
Rear
Note: As outlined in the preceding table,
there are different sized tires and wheels on
the front and rear positions. In order to
identify that wheels are in their correct
position, check the valve hole location as
indicated in the following chart:
53
2022 Mustang (CZG) Mach 1, enUSA, Edition date: 202110, First-Printing Wheels and Tires

•
Inspect your tires for damage on a
regular basis. If a tire is damaged,
replace it immediately.
• Proper suspension alignment is critical
for maximum performance and
optimal tire wear. If you notice uneven
tire wear, check your alignment.
• When replacing tires, the only way to
maintain original performance is to use
the original equipment tire. If you use
a different tire, use the same size,
speed rating and load rating and
replace as a set of four. Never mix tire
brands.
• Rotate tires as recommended in the
tire rotation information. Your vehicle
has a staggered tire configuration.
Rotate the tires from side to side only,
not from front to back. See your
owner's manual for more information. USING WINTER TIRES
The original equipment tires on your vehicle
are designed to optimize its performance
in dry or wet summer road conditions.
They are not optimized for off-road or
winter performance and you must not use
them with snow chains. The use of any
type of snow chains with the original equipment wheels and tires of your vehicle
may cause damage not covered by the
vehicle warranty. We do not recommend
using the original equipment tires when
temperatures drop below 45°F (7°C) or in
snow and ice conditions.
Note:
We recommend that you use winter
or all-season tires when temperatures drop
below 45°F (7°C) or in snow and ice
conditions.
• Use winter tires with the same load
index as the summer tires originally
equipped with your vehicle.
• If you fit winter tires with a speed rating
less than the original equipment tires,
do not exceed the maximum speed
rating for the tire. Do not operate your
vehicle above posted speed limits
while using winter tires. Never perform
high speed driving with winter tires.
55
2022 Mustang (CZG) Mach 1, enUSA, Edition date: 202110, First-Printing Wheels and TiresE209823