warning FORD PROBE 1996 2.G Repair Manual

157
*
[DR08800(ALL)03/95]
Parking
*
[DR08900(ALL)03/95]
To park your vehicle, shift into 1 (First), set the
parking brake fully, and turn off the ignition.
*
[DR09000(ALL)05/95]
RWARNING
Do not park your vehicle in Neutral, it
may move unexpectedly and injure
someone. Use 1 (First) gear and set the
parking brake fully.
*
[DR09100(ALL)01/95]
Steering Your Vehicle
[DR09200(ALL)01/94]
Your vehicle is equipped with power steering.
Power steering uses energy from the engine to
help steer your vehicle.
%*
[DR09250(ALL)04/95]
If the amount of effort needed to steer your
vehicle changes at a constant vehicle speed, have
the power steering system checked. If the power
steering system breaks down (or if the engine is
turned off), you can steer the vehicle manually
but it takes more effort.
*
[DR09300(ALL)01/95]
Never hold the steering wheel to the extreme
right or left for more than five seconds if the
engine is running. This can damage the power
steering pump.
*
[DR09500(ALL)03/95]
Brakes
%*
[DR09600(ALL)01/95]
Applying the Brakes
*
[DR09700(ALL)05/95]
Your vehicle may have four-wheel power
anti-lock disc brakes which adjust automatically
through everyday use.
*
[DR09750(ALL)05/95]
Some models have power front disc brakes and
rear drum brakes which automatically adjust as
the brake pads and linings wear down.
File:prdrp.ex
Update:Fri Jun 23 19:35:02 1995

159
*
[DR10530(ALL)05/95]
If the brake pedal is applied while the vehicle is
driven over uneven road surfaces, the ABS may
cycle and the driver may sense a pulsation in
the brake pedal, accompanied by a slight up and
down movement of the pedal height and a
clicking sound. This may also happen when
driving on an inclined surface such as a
driveway while making a sharp turn. This is a
normal condition.
*
[DR10540(ALL)05/95]
Each time you turn the ignition key to the ON
position, the ABS will function through one test
cycle. When this happens, the ABS light will
come on for up to five seconds. If the light stays
on longer than five seconds, shut off the engine
and restart. If it remains on, it means the ABS is
disabled and should be serviced immediately to
restore the benefits of the anti-lock feature.
Normal braking is not affected unless the red
BRAKE system warning light is also lit.
*
[DR10550(ALL)05/95]
ABS has self-check capabilities. As described
above, the system turns on the ABS light each
time you start your engine. After the engine is
started and the ABS light turns off, the system
performs another test the first time the vehicle
reaches 4-9 mph (6-15 km/h). The system turns
on the ABS pump motor for approximately 1/2
second. At this time, a mechanical noise may be
heard. This is a normal part of the self-check
feature. If a malfunction is found during this
check the ABS light will come on.
[DR10560(ALL)05/95]
Ford Motor Company has not found any
detrimental effects of popular mobile road
transmitting equipment installed on vehicles
equipped with the Anti-lock Brake System if
normal radio installation practices are rigidly
followed. However, if after installing mobile
radio transmitting equipment, the Anti-lock
Brake System light comes on at any time other
than immediately after turning the key to the
File:prdrp.ex
Update:Fri Jun 23 19:35:02 1995

161
*
[DR11100(ALL)11/91]
RWARNING
To prevent personal injury, do not release
the parking brake while outside the
vehicle.
*
[DR11200(ALL)05/95]
RWARNING
Always set the parking brake fully and
make sure that the gearshift is securely
latched in P (Park) (automatic transaxle) or
in 1 (First) (manual transaxle).
*
[DR11400(ALL)03/95]
Always check the Brake Warning Light each
time you start your engine. Driving with the
parking brake on will cause the brakes to wear
out quickly and will reduce the fuel economy.
*
[DR11500(ALL)01/93]
RWARNING
If the parking brake is fully released, but
the Brake System light remains on, have
the brakes checked immediately. They
may not be working properly.
*
[DR11600(ALL)01/95]
The parking brake is not designed to stop a
moving vehicle, but you can use the parking
brake to stop your vehicle in an emergency if
the normal brakes fail. However, since the
parking brake applies only the rear brakes, the
stopping distance will increase greatly and the
handling of your vehicle will be adversely
affected.
File:prdrp.ex
Update:Fri Jun 23 19:35:02 1995

163
*
[DR15700(ALL)05/95]
RWARNING
To avoid losing control on slippery roads,
do not downshift into 1 (First) with the
automatic transaxle when moving faster
than 20 mph (32 km/h). Do not downshift
into 1 (First) with the manual transaxle
when moving faster than 10 mph
(16 km/h).
*
[DR15750(ALL)03/95]
RWARNING
If your vehicle has speed control, do not
use it on slippery roads. You could lose
control of your vehicle and could injure
someone.
*
[DR15800(ALL)01/95]
If you have an automatic transaxle and your
vehicle gets stuck (for example, in mud or
snow), you may try to ªrockº it out of the spot.
Shift, in a steady rhythm, between forward and
reverse gears. While in each gear, press lightly
on the accelerator and release.
*
[DR15900(ALL)05/95]
RWARNING
Do not spin the wheels at over 35 mph
(55 km/h). The tires may fail and injure a
passenger or bystander.
*
[DR16000(ALL)03/95]
By moving the vehicle backward and forward,
you may gain enough momentum to move out
of the spot. If you are still stuck after a minute
or two of rocking, call for a tow truck.
[DR16100(ALL)03/95]
Do not rock the vehicle for more than a few
minutes. This may overheat the engine, damage
the transaxle, or damage the tires.
File:prdrp.ex
Update:Fri Jun 23 19:35:02 1995

165
*
[DR17000(ALL)02/95]
RWARNING
If the GVWR or the GAWR specified on
the Safety Compliance Certification Label
is exceeded, your vehicle may be damaged
or you may lose control and injure
someone.
%*
[DR18250(ALL)01/95]
Limiting Your Vehicle's Load
[DR18300(ALL)05/95]
The load you add to your vehicle must not
exceed the maximum load stated on the tire
information decal.
*
[DR18400(ALL)01/95]
To figure the weight of your vehicle's load, add
the weights of:
*
[DR18500(ALL)01/95]
q
the driver and passengers
*
[DR18600(ALL)01/95]
q
luggage and any other items that you put in
your vehicle
*
[DR18800(ALL)01/95]
q
the weight of any equipment that has been
added to your vehicle since it was delivered
to your dealer
*
[DR18900(ALL)01/95]
If you do not know the actual weights of these
items, use the following procedure to figure the
weight of a load:
*
[DR19000(ALL)01/95]
1. Weigh your vehicle without the driver,
passengers and luggage. You might take
your vehicle to a shipping company or an
inspection station for trucks.
*
[DR19100(ALL)01/95]
2. Then weigh your vehicle with the driver,
passengers and luggage.
*
[DR19200(ALL)01/95]
3. Subtract the first reading from the second to
figure the total weight of the load.
File:prdrp.ex
Update:Fri Jun 23 19:35:02 1995

166
*
[DR19300(ALL)01/95]
After determining this load, you must also make
sure that the total weight of your vehicle, plus
the load it carries, is less than its GVWR. Also,
make sure that the weight your vehicle carries
over each axle is less than the GAWR for the
respective axle.
*
[DR19500(ALL)01/95]
If your vehicle exceeds the GVWR, remove cargo
from your vehicle accordingly. If your vehicle
exceeds the GAWR for either axle, shift the load
or remove cargo accordingly.
*
[DR19550(ALL)05/95]
RWARNING
Improper distribution of your vehicle's
load or carrying weight in excess of the
amount shown on the tire decal can cause
rapid tire wear or loss of vehicle control.
*
[DR20000(ALL)04/95]
Towing a Trailer
[DR21000(ALL)01/95]
Do not use your vehicle for towing a trailer.
*
[DR22320(ALL)03/91]
Towing Behind Another Vehicle Ð
Recreational Vehicle
*
[DR22350(ALL)02/92]
Towing an automatic transaxle (ATX) equipped
vehicle behind another vehicle, such as a
Recreational Vehicle (RV), is not recommended
unless a front wheel dolly or trailer is used. Do
not tow your ATX equipped vehicle with the
front wheels on the ground or transaxle damage
may occur.
File:prdrp.ex
Update:Fri Jun 23 19:35:02 1995

167
*
[DR22355(ALL)09/93]
Towing a manual transaxle (MTX) equipped
vehicle behind another vehicle, such as a
Recreational Vehicle (RV), is allowed only if it is
towed forward. The parking brake must be
released, the gearshift must be in Neutral, the
ignition key must be in the ACC position, the
battery must be disconnected to eliminate battery
drain, and the steering wheel unlocked. You
may tow your MTX equipped vehicle only in a
forward direction with the front wheels on the
ground without damage to the transaxle.
*
[DR22358(ALL)02/92]
Do not tow your manual transaxle equipped
vehicle at a speed faster than 55 mph
(88 km/h). The maximum towing distance is
unlimited.
*
[DR22360(ALL)05/95]
RWARNING
Never use a tow bar that attaches to the
bumper when you tow your vehicle. This
could damage the bumper and cause an
accident.
File:prdrp.ex
Update:Fri Jun 23 19:35:02 1995

169
Roadside Emergencies
*
[RE00400(ALL)03/95]
Jump-Starting Your Vehicle
[RE00650(ALL)05/91]
Your vehicle has a Motorcraft maintenance-free
battery. Your vehicle's battery may die if you
leave the lights on or any electrical equipment
on after you turn the engine off. If this happens,
you may be able to jump-start from a booster
battery to start your vehicle.
*
[RE00700(ALL)02/95]
RWARNING
The gases around the battery can explode
if exposed to flames, sparks, or lit
cigarettes. An explosion could result in
injury or vehicle damage.
*
[RE00800(ALL)02/95]
RWARNING
To protect yourself when charging a
battery, always shield your face and eyes.
Make sure that you can breathe fresh air.
%*
[RE00900(ALL)05/95]
RWARNING
Applying too much pressure on the ends
when lifting a battery could cause acid to
spill. Lift the battery with a carrier or
with your hands on the opposite corners.
%*
[RE01000(ALL)05/95]
RWARNING
Batteries contain sulfuric acid which burns
skin, eyes, and clothing.
File:prrep.ex
Update:Fri Jun 23 19:34:36 1995

170
*
[RE01010(ALL)06/95]
If the acid touches someone's skin, eyes, or
clothing, immediately flush the area with water
for at least 15 minutes. If someone swallows the
acid, have him or her drink lots of milk or water
first, then Milk of Magnesia, a beaten egg, or
vegetable oil. Call a doctor immediately.
*
[RE01100(ALL)12/89]
RWARNING
Do not push-start your vehicle. You could
damage the catalytic converter. For further
information, seeJumper Cablesin the
Index.
*
[RE01200(ALL)03/95]
To avoid damaging your vehicle or your battery,
and to avoid injury to yourself, follow these
directions for preparing your vehicle to
jump-start and connecting the jumper cables in
the order they are given. If in doubt, call for
road service.
*
[RE01300(ALL)03/95]
Preparing Your Vehicle
*
[RE01400(ALL)03/95]
1. Your vehicle has a 12-volt starting system, so
you need to use a 12-volt jumper system.
You will damage your starting motor,
ignition system, and other electrical parts if
you connect them to a 24-volt power supply
(either two 12-volt batteries in series or a
24-volt generator set).
*
[RE01500(ALL)03/95]
2. Do not disconnect the battery of the disabled
vehicle. You could damage the vehicle's
electrical system.
*
[RE01600(ALL)04/95]
3. Park the booster vehicle close to the hood of
the disabled vehicle.Make sure the vehicles
do not touch each other.Set the parking
brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
File:prrep.ex
Update:Fri Jun 23 19:34:36 1995

171
*
[RE01700(ALL)03/95]
4. Check all battery terminals and remove any
excessive corrosion before you attach the
jumper cables.
*
[RE01800(ALL)03/95]
5. Turn on the heater fan in both vehicles.
Press the DEFROST button. Turn off all
other switches and gauges.
%*
[RE01900(ALL)05/95]
Connecting the jumper cables
*
[RE02000(ALL)03/95]
1. Connect one end of the first jumper cable to
the positive (+) terminal of the discharged
battery. (You can connect either jumper cable
to the positive (+) terminal, as long as you
use the same cable for both positive
terminals.) Most jumper cables have a red
cable and a black cable. The red cable is
generally used for the positive terminals and
the black for the negative ones.
*
[RE02100(ALL)04/95]
2. Connect the other end of the first cable to
the positive (+) terminal of the booster
battery.
*
[RE02200(ALL)05/95]
3. Connect one end of the second cable to the
negative (-) terminal of the booster battery
Ð NOT to the discharged battery.
*
[RE02300(ALL)04/95]
4. Connect the other end of the second cable to
a good metallic surface on the engine or
frame of the disabled vehicle.
*
[RE02400(ALL)05/95]
RWARNING
Do not connect the end of the second
cable to the negative (-) terminal of the
battery to be jumped. A spark may cause
an explosion of the gases that surround
the battery.
File:prrep.ex
Update:Fri Jun 23 19:34:36 1995