check engine FORD RANGER 1996 2.G Owner's Manual

280
[SV20075(ALL)09/95]
RWARNING
Be careful not to add engine coolant to the windshield
washer fluid reservoir. If sprayed on the windshield,
engine coolant could make it difficult to see through the
windshield.
[SV20100(ALL)09/95]
When the engine is cool, add a 50/50 mixture of engine coolant
and water to the engine coolant recovery reservoir Ð DO NOT
ADD DIRECTLY TO THE RADIATOR. Add straight water only
in an emergency, but you should replace it with a 50/50
mixture of coolant and distilled water as soon as possible.
[SV20125(ALL)09/95]
Check the coolant level in the coolant recovery reservoir the
next few times you drive the vehicle. If necessary, add enough
of a 50/50 mixture of coolant and water to bring the liquid
level to the fill line on the reservoir.
[SV20150(ALL)09/95]
RWARNING
Never remove the coolant recovery cap while the engine
is running or hot.
[SV20175(ALL)09/95]
If you must remove the coolant recovery cap, follow these steps
to avoid personal injury caused by escaping steam or engine
coolant:
[SV20200(ALL)09/95]1.
Before you remove the cap, turn the engine off and let it
cool.
[SV20225(ALL)09/95]2.
When the engine is cool, wrap a thick cloth around the cap
and turn it slowly, counterclockwise to the first stop.
[SV20250(ALL)09/95]3.
Step back while the pressure releases.
[SV20275(ALL)09/95]4.
When you are sure that all the pressure has been released,
use the cloth to press the cap down, turn it counterclockwise,
and remove it.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

Servicing Your Ranger
281
[SV20295(ALL)09/95]
Use Ford Premium Engine Coolant E2FZ-19549-AA (in Canada,
Motorcraft CXC-8-B) or an equivalent premium engine coolant
that meets Ford specification ESE-M97B44-A. Ford Premium
Engine Coolant is an optimized formula that will protect all
metals and rubber elastomers used in Ford cooling systems for 4
years or 50,000 miles (80,000 km).
[SV20300(ALL)09/95]
Do not use alcohol or methanol antifreeze or any engine
coolants mixed with alcohol or methanol antifreeze. Do not use
supplemental coolant additives in your vehicle. These additives
may harm your engine cooling system. The use of an improper
coolant may void the warranty of your vehicle's engine cooling
system.
[SV20325(ALL)09/95]
Recycled engine coolant
[SV20350(ALL)09/95]
Ford Motor Company recommends that Ford and
Lincoln-Mercury dealers use recycled engine coolant produced
by Ford-approved processes. Not all coolant recycling processes
produce coolant which meets Ford specification ESE-M97B44-A,
and use of such coolant may harm engine and cooling system
components.
[SV20375(ALL)09/95]
Always dispose of used automotive fluids in a responsible
manner. Follow your community's regulations and standards for
recycling and disposing of automotive fluids.
[SV20400(ALL)09/95]
Coolant refill capacity
[SV20425(ALL)09/95]
To find out how much fluid your vehicle's cooling system can
hold, seeRefill capacities for fluidsin the Index.
[SV20450(ALL)09/95]
Have your dealer check the engine cooling system for leaks if
you have to add more than a quart (liter) of engine coolant per
month.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

282
[SV20475(ALL)09/95]
Severe winter climate
[SV20490(ALL)09/95]
If you drive in extremely cold climates (less than-34ÊF [-36ÊC]),
it may be necessary to increase the coolant concentration above
50%. Refer to the chart on the coolant container to ensure the
coolant concentration in your vehicle is such that the coolant
will not freeze at the temperature level in which you drive
during winter months. Never increase the engine coolant
concentration above 60%. Leave a 50/50 mixture of engine
coolant and water in your vehicle year-round in non-extreme
climates.
%*
[SV20500(ALL)08/95]
Checking Hoses
*
[SV20600(ALL)10/89]
Inspect all engine and heater system hoses for deterioration,
leaks and loose clamps before adding or replacing engine
coolant. Make whatever repairs or replacements that are
necessary using Motorcraft parts or their equivalents.
%*
[SV20700(ALL)08/95]
Engine Coolant Drain and Flush
*
[SV20800(ALL)10/89]
To drain your vehicle's engine coolant:
*
[SV20900(ALL)03/94]1.
Turn off the engine and let it cool. Fully depressurize the
engine cooling system by covering the radiator cap with a
thick cloth and turning it slowly counterclockwise to the first
stop. Step back while the pressure releases.
*
[SV20950(ALL)05/90]2.
Remove the cap.
*
[SV21000(ALL)05/90]3.
Attach a small hose to the drain tube at the bottom of the
radiator.
*
[SV21200(ALL)05/90]4.
Let the engine coolant drain into a suitable container.
Disconnect the lower radiator hose at the radiator connector
and drain any remaining engine coolant into a container.
*
[SV21250(ALL)05/95]
Proper procedures for flushing the cooling system can be found
in theService Manual.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

Servicing Your Ranger
283
%*
[SV21300(ALL)08/95]
Engine coolant refill procedure
*
[SV21400(ALL)10/89]
After you have drained the engine cooling system:
[SV21700(ALL)10/89]1.
When cold, fill the radiator to a level 1 to 1 1/2 inches
(38 mm) below the filler neck seat.
*
[SV21900(ALL)03/94]2.
Replace the radiator cap to its fully installed position, then
back off to the first stop. This will prevent high pressure
from building up in the cooling system during this part of
the fill procedure.
*
[SV22100(ALL)10/89]3.
Start and idle the engine until the thermostat opens and the
radiator upper hose becomes warm.
*
[SV22200(ALL)05/95]4.
Shut off the engine and allow the engine to cool. Cover the
radiator cap with a thick cloth and cautiously remove it. Step
back while the pressure releases.
*
[SV22500(ALL)10/89]5.
Finally, check the radiator and add more engine coolant if
needed, following the procedures noted above. Reinstall the
radiator cap securely, when finished.
*
[SV22525(ALL)05/90]6.
If more engine coolant is necessary, fill the overflow
reservoir to the appropriate level marked on the bottle.
%*
[SV22700(ALL)03/95]
Windshield Washer Fluid and Wipers
%*
[SV22800(ALL)03/95]
Washer Fluid
*
[SV22900(ALL)01/95]
Check the level of the windshield washer fluid every time you
stop for fuel. The reservoir for washer fluid is located on the
passenger's side of the engine compartment. Visual inspection
can determine if the washer fluid is adequate. Do not operate
the washer when the reservoir is empty.
*
[SV23300(ALL)05/95]
RWARNING
Do not put windshield washer fluid in the container for
the engine coolant.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

Servicing Your Ranger
289
%*
[SV26450(ALL)03/95]
Traction-Lok Rear Axle (If equipped)
*
[SV26460(ALL)03/95]
This axle provides added drive away traction on slippery
surfaces, particularly when one or more wheels are on a surface
with poor traction.
*
[SV26470(ALL)05/95]
RWARNING
To avoid injury, never run the engine with one wheel off
the ground, such as when changing a tire.
%*
[SV26500(ALL)02/95]
Tire Rotation
*
[SV26600(ALL)03/95]
Because your vehicle's front and rear tires perform different
jobs, they often wear differently. To make sure your tires wear
evenly and last longer, rotate them at the mileage shown in the
Maintenance Schedule and Recordbooklet which came with your
vehicle.
*
[SV26700(ALL)07/92]
Rotate the tires according to the following diagram. If you
notice that the tires wear unevenly, have them checked. If your
light truck has a temporary spare tire, do not include it in the
tire rotation pattern.
*
[SV26750(ALL)03/90]
In situations where the tires differ from front to rear
(snow/traction), simply rotate using a side to side pattern.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

300
*
[SV33701(ALL)05/95]
It is preferable to check the transmission fluid level at normal
operating temperature, after approximately 20 miles (30 km) of
driving. However, if necessary, you can check the fluid level
without having to drive 20 miles to obtain a normal operating
temperature if outside temperatures are above50ÊF (10ÊC).
*
[SV33801(ALL)01/95]
NOTE: If the vehicle has been operated for an extended
period at high speeds or in city traffic during hot
weather, or pulling a trailer, the vehicle should be
turned off for about 30 minutes to allow the fluid to
cool before checking.
%*
[SV33901(ALL)02/95]
Checking the Automatic Transmission Fluid
*
[SV33910(ALL)06/95]
With the vehicle on a level surface, start the engine and move
the transmission shift selector through all of the gear ranges
allowing sufficient time for each position to engage. Securely
latch the transmission shift selector in the P (Park) position,
fully set the parking brake and leave the engine running.
[SV33920(R )09/95]
NOTE: Vehicles equipped with the 4x4 option must have the
4x4 shift selector in any position other than neutral. If
in neutral the vehicle may move.
*
[SV33930(ALL)10/89]
RWARNING
Your vehicle should not be driven if the fluid level is
below the bottom hole on the dipstick and outside
temperatures are above50ÊF (10ÊC).
*
[SV33940(ALL)08/95]
Wipe off the dipstick cap (located on the passenger's side of the
engine), pull the dipstick out and wipe the indicator end clean.
Put the dipstick back into the filler tube and make sure it is
fully seated. Pull the dipstick out and read the fluid level.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

Servicing Your Ranger
305
*
[SV37000(ALL)01/95]
Do not fill the reservoir above the MAX line.
*
[SV37100(ALL)01/95]
If you find that the fluid level is excessively low Ð below the
seam or ridge on the outside of the plastic reservoir Ð have the
brake system inspected.
*
[SV37200(ALL)01/95]
RWARNING
Do not let the reservoir for the master cylinder run dry.
This may cause the brakes to fail.
[SV37500(ALL)04/94]
7-1/2 pica art:0020382-C
Brake master cylinder
%*
[SV37600(ALL)03/95]
Power Steering Fluid
*
[SV37700(ALL)01/95]
Check the level of the power steering fluid at least twice a
year (i.e., every Spring and Fall).
%*
[SV37800(ALL)03/95]
Checking and Adding Power Steering Fluid
*
[SV37900(ALL)02/95]1.
Start the engine and let it run until the power steering fluid
reaches normal operating temperature. The power steering
fluid will be at the right temperature when the engine
coolant temperature gauge in the instrument cluster is near
the center of the NORMAL operating temperature range.
*
[SV38000(ALL)01/95]2.
While the engine idles, turn the steering wheel back and
forth several times. Make sure that the cap assembly is
installed at this time.
*
[SV38100(ALL)05/95]3.
Turn the engine off.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

308
*
[SV39200(ALL)01/95]
If the power steering fluid is low, do not drive your vehicle for
a long period of time before adding fluid. This can damage the
power steering pump.
*
[SV39400(ALL)02/95]
If you check the power steering fluid when it is cold, make sure
that the fluid reaches the FULL COLD range on the dipstick.
The reading will only be accurate if the fluid temperature is
approximately 50 to85ÊF (10 to 30ÊC).
*
[SV39405(ALL)06/93]
NOTE: Do not turn the steering wheel of your vehicle with
the engine off. It could force power steering fluid out
from the reservoir cap or in extreme cases, it could
unseat the cap.
%*
[SV39495(ALL)03/95]
Fuses
[SV39600(ALL)03/95]
Fuses protect your vehicle's electrical system from overloading.
If electrical parts in your vehicle are not working, the system
may have been overloaded and blown a fuse. Before you
replace or repair any electrical parts, check the appropriate
fuses.
[SV39700(ALL)07/94]
The following charts tell you which fuses protect each electrical
part of your vehicle. If a fuse blows, all the parts of your
vehicle that use that circuit will not work.
*
[SV39800(ALL)05/95]
Once you have determined which fuses to check, follow the
procedures underChecking and replacing fuseslater in this
chapter.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

314
[SV42000(R )03/95]
17-1/2 pica
art:0090141-C
Power distribution box
%*
[SV42200(ALL)06/95]
Checking and Replacing Fuses
*
[SV42300(ALL)02/95]
If you need to check a fuse, follow these steps:
[SV43000(ALL)01/95]1.
Find the fuse panel, which is located in the left end of the
instrument panel. The power distribution box (described
earlier in this section) is found in the engine compartment,
mounted on a bracket attached to the left fender apron.
[SV43100(ALL)10/94]
To access the fuse panel, remove the fuse panel cover by
inserting your finger in the divot and pulling on the cover.
The underside of the cover contains four spare fuses. A fuse
pulling tool is located in the lower right corner of the fuse
panel in case you need to replace a blown fuse.
*
[SV43200(ALL)03/94]
The spare fuses for your vehicle are color coded as follows:
10 amp Ð red, 15 amp Ð light blue, 20 amp Ð natural, 30
amp Ð light green.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

324
*
[SV49300(ALL)05/95]
RWARNING
Do not park, idle, or drive your vehicle in dry grass or
other dry ground cover. The emission system heats up
the engine compartment and exhaust system, which can
start a fire.
*
[SV49400(ALL)05/95]
RWARNING
On vehicles without original equipment floor covering or
insulation, do not let passengers ride in your truck in a
manner that allows contact between skin and the metal
floor.
*
[SV49500(ALL)05/95]
Watch for fluid leaks, strange odors, smoke, loss of oil pressure,
the charge warning light, the check engine light, or the
temperature warning light. These sometimes indicate that the
emission system is not working properly.
*
[SV49600(ALL)01/95]
Do not make any unauthorized changes to your vehicle or
engine. Changes that cause more unburned fuel to reach the
exhaust system can increase the temperature of the engine or
exhaust system.
*
[SV49700(ALL)01/95]
By law, anyone who manufactures, repairs, services, sells, leases,
trades vehicles, or supervises a fleet of vehicles is not permitted
to intentionally remove an emission control device or prevent it
from working. In some of the United States and in Canada,
vehicle owners may be liable if their emission control device is
removed or is prevented from working.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996