FORD RANGER 1996 2.G Service Manual
Manufacturer: FORD, Model Year: 1996, Model line: RANGER, Model: FORD RANGER 1996 2.GPages: 369, PDF Size: 3.48 MB
Page 41 of 369
Safety Restraints
39
[SR18501(ALL)09/95]
Follow the child seat manufacturer's instructions to attach the
tether strap to the tether bracket.
*
[SR18950(ALL)06/95]
RWARNING
Only use the tether attachment hole locations shown in
the illustrations. The tether anchor may not perform
properly if the wrong mounting location is used.
*
[SR19595(R )05/95]
In Super Cabs equipped with Center Facing Jump Seats, the
tether strap anchor bracket should be installed only at the center
of the cab's back panel with the child seat in the front center
seating position. Installing an anchor bracket at the right rear of
the cab may increase risk of injury to an occupant of the right
rear center facing jump seat in the event of a collision or
sudden stop. If a tethered child seat is installed in the right
front seating position, secure the tether strap to the webbing of
the buckled right rear lap belt.
*
[SR19600(R )05/95]
RWARNING
Do not install a child seat in a center facing jump seat.
%*
[SR19700(ALL)07/95]
Safety Belts for Children
*
[SR19800(ALL)07/95]
Children who are too large for child safety seats should always
wear safety belts. (See instructions with your child seat, or
contact its manufacturer, to determine maximum size of child
that will safely fit in the seat.)
*
[SR19900(ALL)07/95]
RWARNING
If safety belts are not properly worn and adjusted as
described, the risk of serious injury to the child in a
collision will be much greater.
File:03unsrr.ex
Update:Wed May 1 13:43:56 1996
Page 42 of 369
40
*
[SR20000(ALL)07/95]
If the shoulder belt portion of one of the lap and shoulder belts
can be positioned so that it does not cross or rest in front of the
child's face or neck, the child should wear the lap and shoulder
belt. Moving the child closer to the center of the vehicle may
help provide a good shoulder belt fit.
*
[SR20050(ALL)07/95]
To improve the fit of lap and shoulder belts on children who
have outgrown child safety seats, Ford recommends use of a
belt-positioning booster seat that is labelled as conforming to all
Federal motor vehicle safety standards. Belt-positioning booster
seats raise the child and provide a shorter, firmer seating
cushion that encourages safer seating posture and better fit of
lap and shoulder belts on the child. A belt-positioning booster
should be used if the shoulder belt rests in front of the child's
face or neck, or if the lap belt does not fit snugly on both
thighs, or if the thighs are too short to let the child sit all the
way back on the seat cushion when the lower legs hang over
the edge of the seat cushion. You may wish to discuss the
specific needs of your child with your pediatrician.
*
[SR20200(ALL)07/95]
Lap belts and the lap belt portion of lap and shoulder belts
should always be worn snugly and below the hips, touching the
child's thighs.
*
[SR20300(ALL)08/95]
RWARNING
To reduce the risk of serious injury in a collision,
children should always ride with the seatback upright.
File:03unsrr.ex
Update:Wed May 1 13:43:56 1996
Page 43 of 369
41
Starting Your Ranger
*
[ST01700(ALL)03/95]
Ignition
%*
[ST01800(ALL)01/95]
Understanding the Positions of the Ignition
[ST02000(ALL)04/94]
7-1/2 pica art:0021143-A
The positions of the key in the ignition lock cylinder.
%*
[ST02201(ALL)07/95]
ACCESSORY allows some of your vehicle's electrical accessories
such as the radio and the windshield wipers to operate while
the engine is not running.
*
[ST02301(ALL)01/95]
In order to turn the key from the ON or OFF position to the
ACCESSORY position, you must push the key release button if
your vehicle's manual transmission gearshift is mounted on the
floor.
*
[ST02401(ALL)08/95]
LOCK locks the steering wheel and gearshift lever.
*
[ST02501(ALL)10/95]
RWARNING
LOCK does not lock the gearshift on console or
floor-mounted manual transaxle gearshifts. If the parking
brake is not set and the gearshift is moved out of gear,
your vehicle may move unexpectedly and injure someone.
[ST02600(R )06/95]
A neutral tow feature is available on your vehicle. See your
dealer for more information.
File:04unstr.ex
Update:Wed May 1 13:44:22 1996
Page 44 of 369
42
*
[ST02601(R )05/95]
RWARNING
Do not leave the vehicle unattended with the transfer
case in the N (Neutral) position. Always set the parking
brake fully and turn off the ignition when leaving the
vehicle.
*
[ST02651(ALL)01/95]
LOCK is the only position that allows you to remove the key.
The LOCK feature helps to protect your vehicle from theft.
*
[ST02701(ALL)05/95]
If your key is stuck in the LOCK position and will not turn,
move your steering wheel left or right until the key turns freely.
*
[ST02801(ALL)03/95]
OFF allows you to shut off the engine and all accessories
without locking the steering wheel or the automatic
transmission gearshift lever.
*
[ST02901(ALL)05/95]
ON allows you to test your vehicle's warning lights (except the
brake system warning light) to make sure they work before you
start the engine. The key returns to the ON position once the
engine is started and remains in this position while the engine
runs.
*
[ST02951(ALL)03/95]
START cranks the engine. Release the key once the engine starts
so that you do not damage the starter. The key should return to
ON when you release it. The START position also allows you to
test the brake warning light.
%*
[ST03025(ALL)08/95]
Ignition Key Buzzer or Chime
*
[ST03050(ALL)08/95]
The buzzer or chime will sound if you open the driver's door
while the key is in the ignition. Never leave your vehicle
unattended with the key in the ignition.
File:04unstr.ex
Update:Wed May 1 13:44:22 1996
Page 45 of 369
Starting Your Ranger
43
%*
[ST03076(ALL)02/95]
Removing the Key From the Ignition
*
[ST03100(ALL)08/95]
Procedures for removing your key from the ignition will vary,
depending on the type of gearshift your vehicle has. Gearshift
levers may be mounted on the steering column or on the floor
or console.
[ST03117(ALL)05/91]
If you have a manual transmission, you have a key release lever
which allows you to remove your key from the ignition. The
key release lever is on the upper right of the steering column,
just above the key lock cylinder.
*
[ST03300(ALL)08/95]
If your vehicle's gearshift lever is mounted on the
column:
*
[ST03400(ALL)06/95]1.
Put the gearshift in P (Park).
*
[ST03500(ALL)03/91]2.
Set the parking brake fully before removing your foot from
the service brake. (This will avoid ªbindingº or ªloadingº the
park gear if you park on a grade.)
*
[ST03600(ALL)03/95]3.
Turn the ignition key to LOCK.
*
[ST03700(ALL)03/95]4.
Remove the key.
*
[ST03800(ALL)05/95]
If your vehicle's gearshift lever is mounted on the
floor:
*
[ST03950(ALL)05/95]1.
Put the gearshift in 1 (First).
*
[ST04000(ALL)05/95]2.
Turn the ignition key to OFF.
*
[ST04100(ALL)05/95]3.
Set the parking brake fully before removing your foot from
the service brake.
*
[ST04200(ALL)05/95]4.
Push and hold in the key release button.
*
[ST04300(ALL)05/95]5.
Turn the key to LOCK.
*
[ST04400(ALL)05/95]6.
Remove the key.
File:04unstr.ex
Update:Wed May 1 13:44:22 1996
Page 46 of 369
44
*
[ST04600(ALL)05/95]
RWARNING
Always set the parking brake fully and make sure that
the gearshift is latched in P (Park) (automatic
transmission) or 1 (First) (manual transmission).
*
[ST04750(ALL)01/93]
RWARNING
Do not leave children, unreliable adults, or pets alone in
your vehicle. They could accidentally injure themselves
or others through inadvertent operation of the vehicle.
Further, on hot, sunny days, temperatures in a closed
vehicle could quickly become high enough to cause
severe and possibly fatal injuries to people as well as
animals.
%*
[ST04800(ALL)10/95]
Fuel-Injected Engines
*
[ST04900(ALL)10/95]
When starting a fuel-injected engine,the most important thing
to remember is to avoid pressing down on the accelerator
before or during starting. Only use the accelerator when you
have problems getting your vehicle started. SeeStarting Your
Enginein this chapter for details about when to use the
accelerator while you start your vehicle.
*
[ST04950(ALL)03/95]
Starting Your Vehicle
%*
[ST05200(ALL)05/94]
Preparing to Start Your Vehicle
*
[ST05300(ALL)09/95]
RWARNING
Do not start your vehicle in a closed garage or other
enclosed area. Never sit in a stopped vehicle for more
than a short period of time with the engine running.
Exhaust fumes are toxic. SeeGuarding Against Exhaust
Fumesin this chapter for more instructions.
File:04unstr.ex
Update:Wed May 1 13:44:22 1996
Page 47 of 369
Starting Your Ranger
45
*
[ST05400(ALL)01/95]
Before you start your vehicle, do the following:
*
[ST05500(ALL)08/95]1.
Make sure all occupants in the vehicle buckle their safety
belts. SeeSafety Restraintsin the Index for more details.
*
[ST05600(ALL)03/95]2.
Make sure the headlamps and other accessories are turned
off when starting.
*
[ST05700(ALL)10/94]3.
If you have an automatic transmission,make sure that the
gearshift lever is in P (Park) and the parking brake is set
before you turn the key.
*
[ST05800(ALL)03/91]4.
If you have a manual transmission,make sure that the
parking brake is fully set, push the clutch pedal to the floor,
and put the gearshift into Neutral before you turn the key.
(Remember, the starter will operate only if the clutch pedal
is pushed in all the way).
*
[ST06000(ALL)03/95]
Before you start your vehicle, you should test the warning lights
on the instrument panel to make sure that they work. Refer to
theWarning Lights and Gaugeschapter.
%*
[ST06200(ALL)02/95]
Starting Your Engine
*
[ST06300(ALL)06/95]
To start your engine:
*
[ST06400(ALL)05/95]1.
Follow the steps underPreparing to Start Your Vehicleat the
beginning of this section.
*
[ST06425(ALL)03/95]2.
Turn the ignition key to the ON position.
*
[ST06451(ALL)06/95]3.
DO NOT depress the accelerator pedal when starting your
engine. DO NOT use the accelerator while the vehicle is
parked.
*
[ST06475(ALL)02/95]4.
Turn the key to the START position (cranking) until the
engine starts. Allow the key to return to the ON position
after the engine has started.
*
[ST06501(ALL)02/95]
If you have difficulty in turning the key, rotate the steering
wheel slightly because it may be binding.
File:04unstr.ex
Update:Wed May 1 13:44:22 1996
Page 48 of 369
46
%*
[ST06510(ALL)04/95]
For a cold engine:
*
[ST06515(ALL)06/95]
n
At temperatures10ÊF (-12ÊC) andbelow:If the engine does
not start infifteen (15) secondson the first try, turn the key
to OFF, wait approximately ten (10) seconds so you do not
flood the engine, then try again.
*
[ST06520(ALL)04/95]
n
At temperaturesabove10ÊF(-12ÊC):If the engine does not
start infive (5) secondson the first try, turn the key to OFF,
wait approximately ten (10) seconds so you do not flood the
engine, then try again.
%*
[ST06521(ALL)05/95]
For a warm engine:
*
[ST06522(ALL)04/95]
n
Do not hold the key in the START position for more than
five (5) secondsat a time. If the engine does not start within
five (5) seconds on the first try, turn the key to the OFF
position. Wait a few seconds after the starter stops, then try
again.
*
[ST06575(ALL)08/95]
Whenever you start your vehicle, release the key as soon as the
engine starts. Excessive cranking could damage the starter.
*
[ST06601(ALL)09/95]
After starting, allow the engine to idle for a few seconds before
driving away.
%*
[ST06775(ALL)04/95]
If the engine does not start after two attempts:
*
[ST06825(ALL)04/95]1.
Turn the ignition key to the OFF position.
*
[ST06851(ALL)04/95]2.
Press the accelerator all the way to the floor and hold it.
*
[ST06876(ALL)04/95]3.
Turn the ignition key to the START position.
*
[ST06900(ALL)04/95]4.
Release the ignition key when the engine starts.
*
[ST06925(ALL)04/95]5.
Release the accelerator gradually as the engine speeds up.
Then drive away in the normal manner.
*
[ST06951(ALL)04/95]
If the engine still does not start, the fuel pump shut-off switch
may have been triggered. For directions on how to reset the
switch seeFuel Pump Shut-Off Switchlater in this chapter.
File:04unstr.ex
Update:Wed May 1 13:44:22 1996
Page 49 of 369
Starting Your Ranger
47
%*
[ST07300(ALL)10/95]
A computer system controls the engine's idle speed. When you
start your vehicle, the engine's idle speed normally runs high.
These faster engine speeds will make your vehicle coast slightly
faster than its normal idle speed. It should, however, slow down
after a short time. If it does not, have the idle speed checked.
*
[ST07390(ALL)07/95]
If the engine idle speed does not slow down automatically, do
not allow your vehicle to idle for more than 10 minutes. Have
the vehicle checked.
*
[ST07400(ALL)05/95]
RWARNING
Extended idling at high engine speeds can produce very
high temperatures in the engine and exhaust system,
creating the risk of fire or other damage.
*
[ST07450(ALL)05/95]
RWARNING
Do not park, idle, or drive your vehicle in dry grass or
other dry ground cover. The emission system heats up
the engine compartment and exhaust system, which can
start a fire.
*
[ST07500(ALL)03/95]
If you consistently start your vehicle in subzero temperatures,
use an engine block heater (if your vehicle has this option).
%*
[ST07600(ALL)06/95]
Engine Block Heater (If equipped)
*
[ST07700(ALL)03/95]
Engine block heaters are strongly recommended if you live in a
region where temperatures reachs20ÊF (s29ÊC) orbelow
consistently during the winter months. An engine block heater
warms the engine coolant, which improves starting, warms up
the engine faster, and allows the heater-defrost system to
respond quickly.
File:04unstr.ex
Update:Wed May 1 13:44:22 1996
Page 50 of 369
48
*
[ST08000(ALL)05/95]
RWARNING
To prevent electrical shock, do not use your heater with
ungrounded electrical systems or two-pronged (cheater)
adapters.
*
[ST08100(ALL)03/95]
For best results, plug the heater in at least three hours before
you start your vehicle. Using the heater for longer than three
hours will not damage the engine, so you can plug it in at night
to start your vehicle the following morning.
*
[ST08150(ALL)12/91]
NOTE: Be sure to disconnect the engine block heater before
driving your vehicle.
%*
[ST08175(ALL)03/95]
If the Engine Cranks but Does Not Start or
Does Not Start After a Collision
*
[ST08200(ALL)07/95]
The Fuel Pump Shut-off Switch
*
[ST08210(ALL)10/95]
If the engine cranks but does not start or does not start after a
collision, the fuel pump shut-off switch may have been
triggered. The shut-off switch is a device intended to stop the
fuel pump when your vehicle has been involved in a major jolt.
*
[ST08215(ALL)03/95]
Once the shut-off switch is triggered, you must reset the switch
by hand before you can start your vehicle.
File:04unstr.ex
Update:Wed May 1 13:44:22 1996