fuel FORD RANGER 1996 2.G Service Manual

276
%*
[SV13775(ALL)01/95]
Checking and Adding Engine Oil
*
[SV13800(ALL)03/95]
Since the proper amount of engine oil is important for safe
engine operation, check the oil using the dipstick each time you
put fuel in your vehicle. Remember the engine must be off, the
oil must be warm and the vehicle must be parked on level
ground.
%*
[SV13900(ALL)04/95]
Checking the engine oil level:
*
[SV14000(ALL)02/95]1.
Turn the engine off after it has warmed up and allow a few
minutes for the engine oil to drain back into the oil pan.
*
[SV14050(ALL)06/95]2.
Set the parking brake, making sure the gearshift is securely
latched in P (Park) or 1 (manual transmission).
*
[SV14100(ALL)02/95]3.
Open the hood. Protect yourself from engine heat.
*
[SV14200(ALL)03/95]4.
Locate the engine oil dipstick (highlighted in yellow) and
carefully pull it out of the engine.
*
[SV14300(ALL)01/95]5.
Wipe the dipstick clean and put it back into position, making
sure it is fully seated.
[SV14400(ALL)10/94]
7-1/2 pica art:0021256-B
Engine oil dipstick
[SV14500(ALL)10/94]6.
Carefully, pull the dipstick out again. If the oil level is below
the ªADDº line, add engine oil as necessary. If the oil level
is beyond the letter ªFº in Full, engine damage or high oil
consumption may occur and some oil must be removed from
the engine.
*
[SV14600(ALL)01/95]7.
Put the dipstick back in and make sure it is fully seated.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

278
*
[SV17150(ALL)09/95]
NOTE: SeeRefill Capacities, Motorcraft Parts and Lubrication
Specificationsin this chapter for the appropriate oil
filter and engine oil refill quantity.
%*
[SV17250(ALL)09/95]
NOTE: Always dispose of used automotive fluids in a
responsible manner. Follow your community's
standards for disposing of these types of fluids. Call
your local recycling center to find out about recycling
automotive fluids.
*
[SV17275(ALL)07/95]
RWARNING
Continuous contact with USED motor oil has caused
cancer in laboratory mice.
*
[SV17285(ALL)07/95]
Protect your skin by washing with soap and water.
%*
[SV17300(ALL)03/95]
Engine Coolant
%*
[SV17400(ALL)09/95]
Checking the engine coolant
*
[SV17500(ALL)09/95]
NOTE: Be sure to read and understandPrecautions When
Servicing Your Vehicleat the beginning of this chapter.
*
[SV17700(ALL)08/95]
Your vehicle's engine coolant protects the engine from
overheating in the summer and from freezing in the winter.
Check the level of the engine coolant at least once a month, but
preferably each time you stop for fuel. Simply look at the
engine coolant recovery reservoir located in the engine
compartment. To locate this reservoir, see the diagram of your
vehicle's engine underEngine typesin this chapter.
*
[SV17750(ALL)03/95]
If the engine coolant has not been checked for a long period of
time the engine coolant reservoir may eventually empty. If the
engine coolant reservoir empties, check the engine coolant level
in the radiator. Read the following warnings before removing
the radiator cap. If it is necessary to fill the radiator, refer to the
Engine Coolant Refill Procedurein this chapter for instructions.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

Servicing Your Ranger
283
%*
[SV21300(ALL)08/95]
Engine coolant refill procedure
*
[SV21400(ALL)10/89]
After you have drained the engine cooling system:
[SV21700(ALL)10/89]1.
When cold, fill the radiator to a level 1 to 1 1/2 inches
(38 mm) below the filler neck seat.
*
[SV21900(ALL)03/94]2.
Replace the radiator cap to its fully installed position, then
back off to the first stop. This will prevent high pressure
from building up in the cooling system during this part of
the fill procedure.
*
[SV22100(ALL)10/89]3.
Start and idle the engine until the thermostat opens and the
radiator upper hose becomes warm.
*
[SV22200(ALL)05/95]4.
Shut off the engine and allow the engine to cool. Cover the
radiator cap with a thick cloth and cautiously remove it. Step
back while the pressure releases.
*
[SV22500(ALL)10/89]5.
Finally, check the radiator and add more engine coolant if
needed, following the procedures noted above. Reinstall the
radiator cap securely, when finished.
*
[SV22525(ALL)05/90]6.
If more engine coolant is necessary, fill the overflow
reservoir to the appropriate level marked on the bottle.
%*
[SV22700(ALL)03/95]
Windshield Washer Fluid and Wipers
%*
[SV22800(ALL)03/95]
Washer Fluid
*
[SV22900(ALL)01/95]
Check the level of the windshield washer fluid every time you
stop for fuel. The reservoir for washer fluid is located on the
passenger's side of the engine compartment. Visual inspection
can determine if the washer fluid is adequate. Do not operate
the washer when the reservoir is empty.
*
[SV23300(ALL)05/95]
RWARNING
Do not put windshield washer fluid in the container for
the engine coolant.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

Servicing Your Ranger
285
%*
[SV24500(ALL)03/95]
Wiper Blades
*
[SV24600(ALL)03/95]
Check the windshield wiper blades at least twice a year. Also
check them whenever they seem less effective than usual. Such
substances as tree sap and some hot wax treatments used by
commercial car washes reduce the effectiveness of wiper blades.
*
[SV24700(ALL)09/95]
If the blades do not wipe properly, clean both the windshield
and the wiper blades. Use undiluted windshield washer solution
or a mild detergent. Rinse thoroughly with clear water. Do not
use fuel, kerosene, paint thinner, or other solvents to clean your
wiper blades. These will damage your blades.
*
[SV24800(ALL)03/95]
To make reaching the wiper blades easy, simply turn the
ignition to the ACC position and turn your wipers on. Wait for
them to reach a vertical position and turn the ignition to the
OFF position. Do not move the wipers manually. Manually
moving the wipers across the windshield may damage them.
*
[SV24900(ALL)03/01]
Wiper blade replacement
[SV25000(ALL)01/95]
If the wipers still do not work properly after you clean them,
you may need to replace the wiper blade assembly or the blade.
When replacing the wiper blade assembly, blade refill, or wiper
arm always use a Motorcraft part or equivalent.
*
[SV25025(ALL)10/93]
To replace the wiper blades:
[SV25030(ALL)10/94]1.
Cycle windshield wiper arm and wiper blade to where
removal of blade can be performed without difficulty. Turn
ignition off at desired position.
[SV25075(ALL)10/94]2.
To remove wiper blade assembly from wiper mounting arm,
depress lock tab and push wiper mounting arm away from
wiper blade assembly.
[SV25100(ALL)10/94]3.
To install wiper blade assembly, pull wiper mounting arm
down on wiper blade until lock tab is engaged.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

Servicing Your Ranger
287
%*
[SV25200(ALL)03/95]
Tires
*
[SV25300(ALL)03/95]
Look at your tires each time you fill your fuel tank. If one tire
looks lower than the others, check the pressure in all of them.
Always follow these precautions:
*
[SV25400(ALL)03/95]
n
Keep your tires inflated to the recommended pressures.
*
[SV25500(ALL)02/95]
n
Stay within the recommended load limits (seeLoad limitsin
the Index).
*
[SV25600(ALL)02/95]
n
Make sure the weight of your load is evenly distributed.
*
[SV25700(ALL)10/89]
n
Drive at safe speeds.
*
[SV25800(ALL)01/95]
If you do not take these precautions, your tires may fail or go
flat.
*
[SV25890(ALL)07/95]
Ford Motor Company recommends obeying posted speed limits.
*
[SV25900(ALL)05/95]
RWARNING
Driving too fast for conditions creates the possibility of
loss of vehicle control. Driving at very high speeds for
extended periods of time may result in damage to vehicle
components.
*
[SV26100(ALL)11/89]
At least once a month, check the pressure in all your vehicle's
tires, including the spare. Use an accurate tire pressure gauge.
Check the tire pressure when tires are cold, that is, after the
vehicle has been parked for at least one hour or has been
driven less than 3 miles (5 km). You can find the proper cold
pressure on the Safety Compliance Certification Label.
*
[SV26150(ALL)05/95]
RWARNING
Improperly inflated tires can affect vehicle handling and
can fail suddenly, possibly resulting in loss of vehicle
control.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

296
*
[SV31600(ALL)01/95]
n
Put the chains on tightly with the ends held down securely.
Verify that no chain touches any wiring, brake lines, or fuel
lines. Follow the chain manufacturer's instructions.
*
[SV31700(ALL)01/95]
n
Drive slowly. If you can hear the chains rub or bang against
your vehicle, stop the vehicle and tighten the chains. If you
continue to hear the chains rub or bang against your vehicle,
remove the chains to prevent damage to your vehicle.
*
[SV31800(ALL)10/94]
n
Avoid fully loading your vehicle if possible.
*
[SV31850(ALL)11/94]
n
Tire chains may affect vehicle handling. Drive carefully and
avoid hard braking.
[SV31900(ALL)03/95]
Remove tire chains at the first opportunity after using them on
snow and ice. Do not use the chains on dry roads.
*
[SV31950(ALL)05/91]
n
Make sure your suspension insulation and bumpers are not
missing or worn to avoid damage to your vehicle.
%*
[SV31960(ALL)04/95]
Cleaning the Wheels
*
[SV31970(ALL)05/95]
Wash the wheels with the same detergent you use to wash your
vehicle's body. Do not use acid-based wheel cleaners, steel wool,
abrasives, fuel, or strong detergents. These substances will
damage protective coatings. Use tar and road oil remover to
remove grease and tar.
*
[SV31975(ALL)09/95]
NOTE: Before going to a car wash, find out if the brushes are
abrasive.
[SV31980(ALL)03/95]
If you have raised white letter tires that are difficult to clean
with regular detergent, use whitewall tire cleaner. Follow the
directions on the container and rinse the tires with plenty of
clean water.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

Servicing Your Ranger
323
*
[SV48400(ALL)10/90]
Rear lighting wire functions
[SV48500(ALL)04/94]
eight pica
chart:0021201-A%*
[SV48600(ALL)03/95]
Emission Control System
*
[SV48700(ALL)05/95]
Your vehicle is equipped with a catalytic converter which
enables your vehicle to comply with applicable exhaust emission
requirements.
*
[SV48800(ALL)05/95]
To make sure that the catalytic converter and the other emission
control parts continue to work properly:
*
[SV48900(ALL)01/95]
n
Use only unleaded fuel.
*
[SV49000(ALL)01/95]
n
Avoid running out of fuel.
*
[SV49100(ALL)01/95]
n
Do not turn off the ignition while your vehicle is moving,
especially at high speeds.
*
[SV49200(ALL)03/95]
n
Have the services listed in yourMaintenance Schedule and
Recordbooklet performed according to the specified schedule.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

324
*
[SV49300(ALL)05/95]
RWARNING
Do not park, idle, or drive your vehicle in dry grass or
other dry ground cover. The emission system heats up
the engine compartment and exhaust system, which can
start a fire.
*
[SV49400(ALL)05/95]
RWARNING
On vehicles without original equipment floor covering or
insulation, do not let passengers ride in your truck in a
manner that allows contact between skin and the metal
floor.
*
[SV49500(ALL)05/95]
Watch for fluid leaks, strange odors, smoke, loss of oil pressure,
the charge warning light, the check engine light, or the
temperature warning light. These sometimes indicate that the
emission system is not working properly.
*
[SV49600(ALL)01/95]
Do not make any unauthorized changes to your vehicle or
engine. Changes that cause more unburned fuel to reach the
exhaust system can increase the temperature of the engine or
exhaust system.
*
[SV49700(ALL)01/95]
By law, anyone who manufactures, repairs, services, sells, leases,
trades vehicles, or supervises a fleet of vehicles is not permitted
to intentionally remove an emission control device or prevent it
from working. In some of the United States and in Canada,
vehicle owners may be liable if their emission control device is
removed or is prevented from working.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

Servicing Your Ranger
335
%*
[SV57350(ALL)01/95]
Engine
*
[SV57400(ALL)01/95]
n
Start engine every 15 days. Run at fast idle until it reaches
normal operating temperature.
*
[SV57500(ALL)01/95]
n
With your foot on the brake, shift through all the gears
while the engine is running.
%*
[SV57600(ALL)01/95]
Fuel system
%*
[SV57700(ALL)07/94]
n
Fill fuel tank with high-quality unleaded fuel until the first
automatic shutoff of the fuel pump nozzle.
*
[SV57900(ALL)03/95]
NOTE: During extended periods of vehicle storage (60 days or
more), fuel may deteriorate due to oxidation. This can
damage rubber and other polymers in the fuel system
and may also clog small orifices.
*
[SV58000(ALL)01/95]
Ford Gas Stabilizer should be added whenever actual or
expected storage periods exceed 60 days. Follow the instructions
on the label. The vehicle should then be operated at idle speed
to circulate the additive throughout the fuel system.
*
[SV58100(ALL)01/95]
A volatile corrosion inhibitor added to the fuel system will
protect the fuel system's inner surfaces from corrosion. Follow
the instructions packaged with the product.
%*
[SV58200(ALL)01/95]
Cooling system
*
[SV58300(ALL)01/95]
n
Protect against freezing temperatures.
File:15unsvr.ex
Update:Wed May 1 13:56:18 1996

355
Index
Emergencies, roadside
assistance...................... 241
battery acid spills................219, 299
fuel........................ 271
jump-starting.................... 219
towing....................... 234
Emergency brake (parking brake)............ 181
Emission control system................ 323
catalytic converter.................. 323
emissions warranty................ 3,323
Engine
check engine warning light............... 60
does not start................... 46,48
fuel injected engine, starting.............. 44
fuel pump shut-off switch............... 48
preparing to start................... 44
service points.................... 262
starting...................... 41,45
starting after a collision................ 48
storing your vehicle................. 334
Engine block heater................... 47
Engine coolant
checking and adding................ 278
checking hoses................... 282
disposal..................258, 278, 301
drain and flush................... 282
preparing for storage................ 335
recovery reservoir.................. 262
refill procedure................... 283
specifications.................... 331
temperature gauge.................. 68
Engine coolant temperature gauge
description...................... 68
mechanical...................... 68
Engine fan...................... 258
File:unixr.ex
Update:Wed May 1 13:58:05 1996