brake light FORD RANGER 1997 2.G User Guide

Driving
185
*
[GF20000(R)01/96]
Sand
*
[GF20100(R)01/96]
When driving over sand, try to keep all four wheels of the
vehicle on the most solid area of the trail. Do not reduce the
tire pressures but shift to a lower gear and drive steadily
through the terrain. Apply accelerator slowly and avoid
spinning the wheels.
*
[GF20200(R)01/96]
Mud and Water
*
[GF20300(R)01/96]
When driving through water, determine the depth; avoid water
higher than the bottom of the hubs (if possible) and proceed
slowly. If the ignition system gets wet, the vehicle may stall.
*
[GF20400(R)01/96]
Once through water, always try the brakes. Wet brakes do not
stop the vehicle as effectively as dry brakes. Drying can be
improved by moving your vehicle slowly, while applying light
pressure on the brake pedal.
*
[GF20500(R)01/96]
After driving through mud, clean off residue stuck to rotating
driveshafts and tires. Excess mud stuck on tires and rotating
driveshafts causes an imbalance which could damage drive
components.
*
[GF20525(R)03/96]
NOTE: If the transmission and transfer case is submerged in
water, their fluids should be checked and changed, if
necessary.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997

214
*
[GF38800(R)03/96]
When descending a steep grade with a trailer, operate in Drive
rather than Overdrive. If additional braking is needed, shift the
automatic transmission gearshift into the 2 (Second) or 1 (Low)
position.
[GF38925(R)05/96]
Servicing Your Vehicle If You Tow
*
[GF38950(R)05/96]
If you tow a trailer for a long distance, your vehicle will need
to be serviced more frequently than usual. Refer to the
Maintenance Schedulebooklet for additional information.
[GF39000(R)01/96]
Trailer towing tips
*
[GF39100(R)01/96]
Before starting on a trip, practice turning, stopping and backing
in an area away from heavy traffic. Get to know the ªfeelº of
the vehicle/trailer combination.
*
[GF39200(R)01/96]
Practice backing up. Back up very slowly, with someone outside
at the rear of your trailer to guide you. Place your hand at the
bottom of the steering wheel and move it in the direction you
want the rear of the trailer to swing. Slight movement of the
steering wheel results in a much larger movement of the rear of
the trailer.
*
[GF39300(R)01/96]
Allow more room for stopping with a trailer attached. Trailer
brakes should be applied first, whether manually or
automatically controlled, when approaching a stop.
*
[GF39400(R)01/96]
For a good handling truck-trailer combination, the trailer tongue
load should be approximately 10-15% of the loaded trailer
weight.
*
[GF39500(R)01/96]
Make a thorough check of your equipment before starting out
on the road. After you have traveled about 50 miles (80 km)
stop in a protected area and double-check your hitch and
electrical connections. Also check trailer wheel lug nuts for
tightness.
*
[GF39600(R)01/96]
When turning, drive slightly beyond the normal turning point
so the trailer wheels will clear curbs or other obstructions.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997

217
Roadside Emergencies
%*[ER00200(R)03/96]Hazard Flasher
*[ER00210(R)01/96]The hazard flasher is used to alert other drivers to hazardous
situations.
*[ER00212(R)03/96]The flashers will flash and the high-mount brakelamp will stay
on steadily (not flash) with the brake pedal depressed.
*[ER00214(R)01/96]The flashers work whether your vehicle is running or not. The
flashers work for up to two hours when the battery is fully
charged and in good condition without draining the battery
excessively. If the flashers run for longer than two hours or if
the battery is not fully charged, the battery power can be
drained.
*[ER00216(R)01/96]To use the hazard flasher:
*[ER00218(R)01/96]1.Push in the flasher button; it will pop out and the lamps will
begin to flash.
*[ER00220(R)01/96]2.To stop the flashers, push in the flasher button again.
*[ER00230(R)01/96]NOTE: The flasher button will be sticking up slightly higher
when on than when off.
[ER00250(R)01/96]
10-1/2 pica
art:0020079-D
Hazard flasher
File:10unerr.ex
Update:Thu Mar 20 08:56:46 1997

Roadside Emergencies
239
%*
[ER25100(R)02/96]
Preparing Your Vehicle
*
[ER25200(R)02/96]1.
Your vehicle has a 12-volt starting system, so you need to
use a 12-volt jumper system. You will damage your starting
motor, ignition system, and other electrical parts if you
connect them to a 24-volt power supply (either two 12-volt
batteries in series or a 24-volt generator set).
*
[ER25300(R)02/96]2.
Do not disconnect the battery of the disabled vehicle. You
could damage the vehicle's electrical system.
*
[ER25400(R)02/96]3.
Park the booster vehicle close to the hood of the disabled
vehicle.Make sure the vehicles do not touch each other.Set
the parking brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
*
[ER25500(R)02/96]4.
Check all battery terminals and remove any excessive
corrosion before you attach the jumper cables.
*
[ER25600(R)02/96]5.
Turn on the heater fan in both vehicles. Turning on the fan
helps protect the electrical system from voltage surges. Turn
off all other switches and lights in both vehicles to prevent
possible damage to either vehicle's electrical systems.
%*
[ER25700(R)02/96]
Connecting the jumper cables
*
[ER25800(R)02/96]1.
Connect one end of the first jumper cable to the positive (+)
terminal of the discharged battery. (You can connect either
jumper cable to the positive (+) terminal, as long as you use
the same cable for both positive terminals.) Most jumper
cables have a red cable and a black cable. The red cable is
generally used for the positive terminals and the black for
the negative ones.
*
[ER25900(R)02/96]2.
Connect the other end of the first cable to the positive (+)
terminal of the booster battery.
*
[ER26000(R)02/96]3.
Connect one end of the second cable to the negative (s)
terminal of the booster battery Ð NOT to the discharged
battery.
File:10unerr.ex
Update:Thu Mar 20 08:56:46 1997

Roadside Emergencies
245
[ER33000(R)01/96]
4x2ÐManualtransmission
*
[ER33100(R)01/96]
n
Release the parking brake.
[ER33200(R)01/96]
n
Place the transmission gearshift in the neutral position.
[ER33300(R)01/96]
n
Maximum speed is limited by towing equipment
manufacturer's recommendation, unlimited distance.
[ER33400(R)01/96]
4x4ÐManualshifttransfercase
*
[ER33500(R)01/96]
n
Release the parking brake.
[ER33600(R)01/96]
n
Place the transmission gearshift in the neutral position.
[ER33700(R)01/96]
n
Place the transfer case gearshift in the neutral position.
[ER33800(R)01/96]
n
Set the manual locking hubs in the FREE position.
[ER33900(R)01/96]
n
Maximum speed is 55 mph (88 km/h), unlimited distance.
[ER34000(R)01/96]
4 x 4 Electric shift transfer case
*
[ER34200(R)01/96]
n
Release the parking brake.
[ER34300(R)01/96]
n
Place the transmission gearshift in the neutral position.
[ER34400(R)05/96]
n
Ensure the transfer case is in 2H and the auto hubs are
unlocked.
[ER34600(R)01/96]
NOTE: Both the 4WD and 4WD Low indicator lights in the
instrument panel will be off when the 4WD switch is
in 2WD.
[ER34700(R)01/96]
For automatic transmissions:
[ER34800(R)01/96]
n
Maximum speed is 35 mph (56 km/h).
[ER34900(R)01/96]
n
Maximum distance is 50 miles (80 km).
File:10unerr.ex
Update:Thu Mar 20 08:56:46 1997

258
*
[MC13730(R)05/96]
NOTE: Ford production and aftermarket (Motorcraft) oil
filters are designed for added engine protection and
long life. If a replacement oil filter is used that does
not meet Ford material and design specifications,
startup engine noises or knock may be experienced. It
is recommended you use the appropriate Motorcraft
oil filter (or another brand meeting Ford
specifications) for your engine application.
%*
[MC13775(R)01/96]
Checking and Adding Engine Oil
*
[MC13800(R)01/96]
Since the proper amount of engine oil is important for safe
engine operation, check the oil using the dipstick each time you
put fuel in your vehicle. Remember the engine must be off, the
oil must be warm and the vehicle must be parked on level
ground.
%*
[MC13900(R)01/96]
Checking the engine oil level:
*
[MC14000(R)01/96]1.
Turn the engine off after it has warmed up and allow a few
minutes for the engine oil to drain back into the oil pan.
[MC14050(R)04/96]2.
Set the parking brake, making sure the gearshift is securely
latched in P (Park) or 1 (manual transmission).
*
[MC14100(R)01/96]3.
Open the hood. Protect yourself from engine heat.
*
[MC14200(R)01/96]4.
Locate the engine oil dipstick (highlighted in yellow) and
carefully pull it out of the engine.
*
[MC14300(R)01/96]5.
Wipe the dipstick clean and put it back into position, making
sure it is fully seated.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997

298
%*
[MC44600(R)03/96]
Lights and Bulb Replacement
*
[MC44700(R)01/96]
It is a good idea to check the operation of the following lights
frequently:
*
[MC44800(R)01/96]
n
headlamps
*
[MC44850(R)01/96]
n
high-mount brakelamp
*
[MC44900(R)01/96]
n
tail lamps
*
[MC45000(R)01/96]
n
brakelamps
*
[MC45100(R)01/96]
n
hazard flasher
*
[MC45200(R)01/96]
n
turn signals
*
[MC45300(R)05/96]
n
license plate lamps
*
[MC45350(R)01/96]
n
fog lamps
%*
[MC45400(R)01/96]
The alignment of your headlamps should be checked if:
*
[MC45500(R)01/96]
n
oncoming motorists frequently signal you to turn off your
vehicle's high beams when you do not have the high beams
on
*
[MC45600(R)01/96]
n
the headlamps do not seem to give you enough light to see
clearly at night
*
[MC45700(R)01/96]
n
the headlamp beams are pointed substantially away from a
position slightly down and to the right
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997

308
*
[MC56600(R)01/96]
Body
*
[MC56700(R)01/96]
n
Wash vehicle thoroughly to remove dirt, grease, oil, tar or
mud from exterior surfaces, rear wheel housing and
underside of front fenders.
*
[MC56800(R)01/96]
n
Periodically wash vehicles stored in exposed locations.
*
[MC56900(R)01/96]
n
Touch-up raw or primed metal to prevent rust.
*
[MC57000(R)01/96]
n
Cover chrome and stainless steel parts with a thick coat of
auto wax to prevent discoloration. Re-wax as necessary when
the vehicle is washed.
*
[MC57100(R)01/96]
n
Lubricate all hood, door and trunk lid hinges and latches
with a light grade oil.
*
[MC57200(R)01/96]
n
Cover interior soft trim to prevent fading.
*
[MC57300(R)01/96]
n
Keep all rubber parts free from oil and solvents.
%*
[MC57350(R)01/96]
Engine
*
[MC57400(R)01/96]
n
Start engine every 15 days. Run at fast idle until it reaches
normal operating temperature.
*
[MC57500(R)01/96]
n
With your foot on the brake, shift through all the gears
while the engine is running.
%*
[MC57600(R)01/96]
Fuel system
%*
[MC57700(R)01/96]
n
Fill fuel tank with high-quality unleaded fuel until the first
automatic shutoff of the fuel pump nozzle.
*
[MC57900(R)01/96]
NOTE: During extended periods of vehicle storage (60 days or
more), fuel may deteriorate due to oxidation. This can
damage rubber and other polymers in the fuel system
and may also clog small orifices.
*
[MC58000(R)01/96]
Ford Gas Stabilizer should be added whenever actual or
expected storage periods exceed 60 days. Follow the instructions
on the label. The vehicle should then be operated at idle speed
to circulate the additive throughout the fuel system.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997

Maintenance and Care
309
*
[MC58100(R)01/96]
A volatile corrosion inhibitor added to the fuel system will
protect the fuel system's inner surfaces from corrosion. Follow
the instructions packaged with the product.
%*
[MC58200(R)01/96]
Cooling system
*
[MC58300(R)01/96]
n
Protect against freezing temperatures.
%*
[MC58400(R)01/96]
Battery
*
[MC58500(R)01/96]
n
Check and recharge as necessary.
*
[MC58600(R)01/96]
n
Keep connections clean and covered with a light coat of
grease.
%*
[MC58700(R)01/96]
Brakes
*
[MC58800(R)01/96]
n
Make sure brakes and parking brake are fully released.
%*
[MC58900(R)01/96]
Tires
*
[MC59000(R)01/96]
n
Maintain recommended air pressure.
*
[MC59100(R)01/96]
Miscellaneous
*
[MC59200(R)01/96]
n
Make sure all linkages, cables, levers and clevis pins under
vehicle are covered with grease to prevent rust.
*
[MC59300(R)01/96]
n
Move vehicles at least 25 feet (8 m) every 15 days to
lubricate working parts and prevent corrosion.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997

Index
343
A
Accessory position on the ignition............. 73
Additives, engine oil.................. 257
Air bag supplemental restraint system
and child safety seats................ 133
description...................122, 127
disposal...................... 131
driver air bag..................122, 127
indicator light..................... 12
operation...................... 127
passenger air bag.................. 127
proper seating................... 123
service and information labels............ 127
tone generator.................129, 131
wearing safety belts................. 123
Air cleaner filter
location...................... 253
specifications.................... 311
Alarm, activating remote personal............. 94
Ambulance packages................... 5
Antenna, radio (see Electronic sound system)...... 27,55
Antifreeze (see Engine coolant)............. 265
Anti-lock brake system (ABS)
description..................... 155
noise........................ 157
see also Brake.................... 155
warninig light..................... 10
Anti-theft system
arming the system................... 98
description...................... 98
disarming an untriggered system............ 99
disarming a triggered system.............. 99
triggering....................... 98
Appeals (see Dispute settlement board)......... 320
Assistance (see Customer assistance)........... 317
File:unixr.ex
Update:Thu Mar 20 09:01:44 1997