lock FORD RANGER 1997 2.G Owner's Manual

101
Seating and Safety Restraints
%*
[SS00125(R)05/96]
Seats
%*
[SS00200(R)01/96]
Adjusting the Front Seat Manually
[SS00210(R)01/96]
Regular Cab
*
[SS00220(R)01/96]
To move the front seat forward or rearward:
*
[SS00222(R)01/96]1.
Find the adjustment lever at the lower left corner of the
front seat.
*
[SS00224(R)01/96]2.
Push the lever to the left to unlock the seat.
*
[SS00226(R)01/96]3.
Move the seat to the desired position.
[SS00228(R)01/96]4.
Release the lever to lock the seat in its new position. Make
sure the seat locks securely in place.
[SS00240(R)01/96]
10-1/2 pica
art:0020859-C
Adjusting the bench seat
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997

104
[SS00330(R)01/96]
Reclining Bucket Seats (If equipped)
[SS00332(R)01/96]
If your vehicle is equipped with the optional reclining bucket
seat, you can tilt the seatback up to 30 degrees rearward.
*
[SS00334(R)01/96]1.
On the side of the seat, find the handle for the recliner.
*
[SS00336(R)01/96]2.
Lift the handle up and hold it in place.
*
[SS00338(R)01/96]3.
Lean against the back of the seat and adjust it to the position
you want.
*
[SS00340(R)01/96]4.
Release the handle to lock the seatback in position.
*
[SS00342(R)01/96]5.
To return the seatback to upright position, lift the handle
and lean forward. Then release the handle.
[SS00354(R)01/96]
Lifting the recliner handle of an unoccupied seat will allow the
seat back to fold forward for access to the rear. Pushing the seat
back with the release handle raised returns the seat back to the
upright position.
[SS00356(R)01/96]
10-1/2 pica
art:0021165-A
Reclining bucket seat
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997

Seating and Safety Restraints
105
*
[SS00549(R)01/96]
Center Facing Jump Seat Ð SuperCab Only
[SS00551(R)01/96]
To open the seat, pull inboard and down on the seat handle. To
stow the seat, pull seat bottom back to the fully upright
position. The jump seats should be kept in the stored position
for easier access to the rear cab area.
[SS00560(R)01/96]
10-1/2 pica
art:0020232-B
Center facing jump seat in stowed position
*
[SS00570(R)01/96]
RWARNING
Do not install a child seat in a center facing jump seat.
[SS00580(R)01/96]
Tilt Slide Seat (If equipped)
[SS00590(R)01/96]
SuperCab only
[SS00610(R)01/96]
With the front seatback tilted forward, the tilt slide seat can be
moved to provide additional entry space to access the rear seat
compartment of the vehicle.
*
[SS00620(R)01/96]
To operate the tilt slide seat:
[SS00622(R)01/96]1.
Lift the seatback release lever on the outboard side of the
seat cushion to unlock the slide mechanism and seatback.
*
[SS00624(R)01/96]2.
Push the seat assembly forward to provide entry space to the
rear seat compartment of the vehicle.
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997

106
*
[SS00630(R)02/96]
RWARNING
Check to see that the seat and seatback are latched
securely in position. Keep floor area free of objects that
would prevent proper seat engagement. Never attempt to
adjust the seat while the vehicle is in motion.
*
[SS00640(R)02/96]
RWARNING
Check to see that the seat and seatback are latched
securely in position. Keep floor area free of objects that
would prevent proper seat engagement. Never attempt to
adjust the seat while the vehicle is in motion.
[SS00650(R)01/96]3.
With the seatback still forward, using the seat cushion push
the seat rearward to the desired position and return the
seatback to its upright position. This will lock the seat track.
[SS00652(R)01/96]
NOTE: Whenever the seatback is returned to the upright
position, the seat will lock in that seat position.
*
[SS00654(R)01/96]
NOTE: The seat can no longer be moved rearward when in
its latched position.
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997

Seating and Safety Restraints
107
[SS00656(R)01/96]
10-1/2 pica
art:0021166-A
Tilt slide seat
*
[SS00670(R)01/96]
Prior to operating the vehicle, check to ensure that the seat
assembly is locked by pushing or pulling the seat forward or
rearward. If seat does not lock, repeat steps 2 and 3.
[SS00675(R)01/96]
10-1/2 pica
art:0021167-B
Locking tilt slide seat
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997

108
*
[SS00680(R)01/96]
To operate the seat adjuster:
[SS00681(R)01/96]4.
To adjust the seats forward or rearward, locate the release
bar at the lower front area of the seat cushion. Lift the
release bar and hold until the desired seat position is
obtained, then release the bar to relock the seat.
[SS00690(R)01/96]
10-1/2 pica
art:0021168-B
Adjusting seat
[SS00700(R)01/96]
60/40 Split Front Bench (If equipped)
[SS00704(R)01/96]
The seat back release operates the same as the basic bucket seat.
[SS00720(R)01/96]
7-1/2 pica art:0020241-D
60/40 split front bench
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997

112
*
[SS02800(R)05/96]
RWARNING
Each seating position in your vehicle has a specific safety
belt assembly which is made up of one buckle and one
tongue that are designed to be used as a pair. 1) Use the
shoulder belt on the outside shoulder only. Never wear
the shoulder belt under the arm. 2) Never swing it
around your neck over the inside shoulder. 3) Never use
a single belt for more than one person.
*
[SS02900(R)02/96]
RWARNING
Lock the doors of your vehicle before driving to lessen
the risk of the door coming open in a collision.
*
[SS02950(R)05/96]
RWARNING
It is extremely dangerous to ride in a cargo area, inside
or outside of a vehicle. In a collision, people riding in
these areas are more likely to be seriously injured or
killed. Do not allow people to ride in any area of your
vehicle that is not equipped with seats and safety belts.
Be sure everyone in your vehicle is in a seat and using a
safety belt properly.
%*
[SS03000(R)02/96]
Combination Lap and Shoulder Belts
*
[SS03200(R)02/96]
While your vehicle is in motion, the combination lap and
shoulder belt adjusts to your movement. However, if you brake
hard, turn hard, or if your vehicle receives an impact of 5 mph
(8 km/h) or more, the lap/shoulder belt locks and helps reduce
your forward movement.
*
[SS03400(R)01/96]
After you get into your vehicle, close the door and lock it. Then
adjust the seat to the position that suits you best.
*
[SS03500(R)02/96]
Pull the combination lap/shoulder belt from the retractor so
that the shoulder portion of the belt crosses your shoulder and
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997

114
*
[SS03513(R)02/96]
While the belt retracts, guide the tongue to its original position
to prevent it from striking you or the vehicle.
*
[SS03514(R)01/96]
Safety Belts for Front Outboard Passenger and Rear
Outboard Seating Positions
*
[SS03516(R)01/96]
Your vehicle is equipped with a dual locking mode retractor on
theshoulderbelt portion of the combination lap/shoulder safety
belt for the front seat outboard passenger and rear outboard
passengers.
*
[SS03518(R)02/96]
Dual locking mode retractors operate in two ways:
*
[SS03519(R)02/96]
Vehicle sensitive (emergency) locking mode
*
[SS03520(R)02/96]
In this operating mode, the shoulder belt retractor will allow the
occupant freedom of movement, locking tight only on hard
braking, hard cornering or impacts of approximately 5 mph
(8 km/h) or more. The retractor can also be made to lock by
pulling the belt out quickly.
%*
[SS03521(R)02/96]
Automatic locking mode
*
[SS03522(R)01/96]
In this operating mode, the shoulder belt retractor will be
automatically locked and will remain locked when the
combination lap/shoulder safety belt is buckled, and does not
allow the occupant freedom of movement. This mode provides
the following:
*
[SS03523(R)01/96]
n
A tight lap/shoulder belt on the occupant.
*
[SS03524(R)01/96]
n
Child safety seat installation.
*
[SS03525(R)01/96]
This modemust be usedwhen installing a child safety seat on
the front passenger seat and rear outboard seats where dual
locking retractors are provided.
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997

Seating and Safety Restraints
115
*
[SS03529(R)01/96]
To switch the retractor from the emergency locking mode to the
automatic locking mode, perform the following steps:
*
[SS03530(R)02/96]1.
Buckle the lap/shoulder combination belt.
*
[SS03531(R)01/96]2.
Grasp the shoulder portion of the belt and pull downward
until all of the belt is extracted and, when allowed to retract,
a clicking sound is heard. At this time, the belt retractor is in
the automatic locking mode (child restraint mode).
*
[SS03532(R)02/96]3.
A clicking sound will continue to be heard as the belt is
allowed to retract. This indicates that the retractor is in the
automatic locking mode.
*
[SS03533(R)02/96]
NOTE: When the combination lap/shoulder belt is unbuckled
and allowed to retract completely, the retractor will
switch to the vehicle sensitive (emergency) locking
mode. See the detailed instructions underSafety Seats
for Childrenin this chapter.
%*
[SS03534(R)01/96]
Shoulder Belt Height Adjustment
*
[SS03535(R)05/96]
Driver and right front passenger
[SS03536(R)01/96]
The driver and right front passenger shoulder belt height is
adjustable to one of four (4) positions (Regular cab model) or
five (5) positions (Super cab model).
*
[SS03537(R)05/96]
To adjust the belt down, push the release button on the adjuster
down and slide the adjuster down. Then release the button and
make sure the adjuster is firmly in one of the positions. To
adjust the belt up, slide the adjuster up. (You do not have to
push the release button.) Slide it up or down until the belt rests
across the middle of your shoulder.
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997

118
[SS03800(R)01/96]
10-1/2 pica
art:0021301-A
Unfastening the outboard lap/shoulder belts
[SS05800(R)01/96]
Center Front Lap Belt (If equipped)
[SS05900(R)01/96]
The lap belt in the center of the front seat does not adjust
automatically. You must adjust it to fit snugly around your
hips. Do not wear it around your waist.
*
[SS05950(R)01/96]
To fasten the belt, pull the belt across your hips and insert the
tongue into the correct buckle on your seat until you hear a
snap and feel it lock. Make sure the buckle is securely fastened.
%*
[SS06100(R)01/96]
If you need to lengthen the belt, unfasten it and tip the belt
tongue at a right angle to the belt. Pull the belt tongue over
your lap until it reaches the buckle.
*
[SS06400(R)01/96]
If you need to shorten the belt, pull on the loose end of the
webbing until the belt fits snugly.
[SS06500(R)01/96]
To unfasten the belt, push the release button on the buckle. This
allows the tongue to unlatch from the buckle.
[SS06600(R)01/96]
Because the center front lap belt does not have a retractor, it
should be shortened and fastened when not in use.
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997