steering wheel FORD RANGER 1997 2.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1997, Model line: RANGER, Model: FORD RANGER 1997 2.GPages: 361, PDF Size: 3.39 MB
Page 64 of 361
Controls and Features
61
%*
[CF00230(R)03/96]
The Interior and Exterior Lights
%*
[CF00235(R)03/96]
Turning On the Exterior Lights
[CF00240(R)04/96]
To turn on your headlamps, parking lamps, marker lamps,
license plate lamps and tail lamps, use the headlamp control
knob to the left of the steering column.
[CF00250(R)03/96]1.
Rotate the headlamp control knob to the first position.
Parking lamps, tail lamps, license plate lamps and marker
lamps are now on.
[CF00255(R)03/96]2.
Rotate the headlamp control knob to the next position.
Headlamps are now on in addition to the above.
[CF00260(R)03/96]3.
Rotate the thumb wheel when the headlamp control knob is
in an ªONº position to brighten or dim the instrument panel
lamps. Rotate fully upward to operate courtesy and cargo
lamps.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997
Page 76 of 361
Controls and Features
73
*
[CF20300(R)01/96]
Clock Controls on Electronic Radios
[CF20400(R)02/96]
The electronic radios have a built-in clock. For complete
operating instructions, refer to theAudio Sectionin this Owner
Guide.
*
[CF20405(R)05/96]
The controls on the steering column and wheel are designed to
give you easy access to the controls while you are driving.
*
[CF20410(R)01/96]
Ignition
%*
[CF20420(R)01/96]
Understanding the Positions of the Ignition
[CF20430(R)01/96]
7-1/2 pica art:0021143-A
The positions of the key in the ignition lock cylinder.
%*
[CF20440(R)04/96]
ACCESSORY allows some of your vehicle's electrical accessories
such as the radio and the windshield wipers to operate while
the engine is not running.
*
[CF20442(R)03/96]
In order to turn the key from the ON or OFF position to the
ACCESSORY position, you must push the key release button if
your vehicle's manual transmission gearshift is mounted on the
floor.
*
[CF20444(R)01/96]
LOCK locks the steering wheel and gearshift lever.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997
Page 77 of 361
74
*
[CF20450(R)01/96]
RWARNING
LOCK position does not lock the gearshift on
floor-mounted manual transaxle gearshifts. If the parking
brake is not set and the gearshift is moved out of gear,
your vehicle may move unexpectedly and injure someone.
*
[CF20470(R)05/96]
RWARNING
Do not leave the vehicle unattended with the transfer
case in the N (Neutral) position. Always set the parking
brake fully and turn off the ignition when leaving the
vehicle.
*
[CF20480(R)01/96]
LOCK is the only position that allows you to remove the key.
The LOCK feature helps to protect your vehicle from theft.
*
[CF20482(R)01/96]
If your key is stuck in the LOCK position and will not turn,
move your steering wheel left or right until the key turns freely.
*
[CF20484(R)01/96]
OFF allows you to shut off the engine and all accessories
without locking the steering wheel or the automatic
transmission gearshift lever.
*
[CF20486(R)01/96]
ON allows you to test your vehicle's warning lights (except the
brake system warning light) to make sure they work before you
start the engine. The key returns to the ON position once the
engine is started and remains in this position while the engine
runs.
*
[CF20490(R)01/96]
START cranks the engine. Release the key once the engine starts
so that you do not damage the starter. The key should return to
ON when you release it. The START position also allows you to
test the brake warning light.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997
Page 82 of 361
Controls and Features
79
%*
[CF26200(R)05/96]
Tilt Steering (If equipped)
*
[CF26250(R)02/96]
RWARNING
Never adjust the steering wheel when the vehicle is
moving.
[CF26400(R)01/96]
7-1/2 pica art:0020088-D
Tilt steering wheel lever
[CF26450(R)04/96]
To change the position of the steering wheel, push the release
lever under the steering column away from you. Tip the
steering wheel to the desired position. Pull the lever back into
place to lock the steering wheel.
*
[CF27250(R)01/96]
Be sure the steering wheel locks in a notch. It is not infinitely
adjustable. Do not adjust the steering wheel while the vehicle is
in motion.
%*
[CF27300(R)03/96]
Speed Control (If equipped)
*
[CF27400(R)05/96]
The speed of the vehicle cannot be automatically controlled until
the vehicle speed is at or above 30 mph (48 km/h).
*
[CF27450(R)05/96]
Use of radio transmitting equipment that is not Federal
Communications Commission (FCC) or in Canada the Canadian
Radio and Telecommunications Commission (CRTC) approved
may cause the speed control to malfunction. Therefore, use only
properly installed FCC (CRTC in Canada) approved radio
transmitting equipment in your vehicle.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997
Page 130 of 361
128
[SS12900(R)01/96]
The driver air bag is in the center of the steering wheel. The
right front passenger seat air bag (if equipped) is in the upper
right hand section of the instrument panel ledge above the
glove compartment.
*
[SS13010(R)05/96]
If a collision occurs, the sensors sense the severity of the impact
and activate the air bags if necessary. The air bag system is
designed to deploy in frontal and front-angled collisions more
severe than hitting a parked vehicle (of similar size and weight)
head-on at about 28 mph (45 km/h). Because the system senses
the crash severity rather than vehicle speed, some frontal
collisions at speeds above 28 mph (45 km/h) will not inflate the
air bag.
*
[SS13020(R)05/96]
When the sensors activate the system, the air bags inflate
rapidly, filling with non-toxic nitrogen gas in a fraction of a
second. Immediately after inflation, the air bags deflate by
releasing the nitrogen gas through vent holes. The whole
process takes place in a matter of seconds.
[SS13025(R)05/96]
RWARNING
Do not place objects or mount equipment on or near the
air bag cover on the steering wheel or in front seat areas
that may come in contact with a deploying air bag.
Failure to follow this instruction may increase the risk of
personal injury in the event of a collision.
*
[SS13030(R)05/96]
RWARNING
Several air bag system components get hot after inflation.
Do not try to touch them after inflation.
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997
Page 149 of 361
148
%*
[TO06200(R)01/96]
Starting Your Engine
*
[TO06300(R)01/96]
To start your engine:
*
[TO06400(R)01/96]1.
Follow the steps underPreparing to Start Your Vehicleat the
beginning of this section.
*
[TO06425(R)01/96]2.
Turn the ignition key to the ON position.
*
[TO06451(R)01/96]3.
DO NOT depress the accelerator pedal when starting your
engine. DO NOT use the accelerator while the vehicle is
parked.
*
[TO06475(R)01/96]4.
Turn the key to the START position (cranking) until the
engine starts. Allow the key to return to the ON position
after the engine has started.
*
[TO06501(R)01/96]
If you have difficulty in turning the key, rotate the steering
wheel slightly because it may be binding.
%*
[TO06510(R)01/96]
For a cold engine:
*
[TO06515(R)01/96]
n
At temperatures10ÊF (-12ÊC) andbelow:If the engine does
not start infifteen (15) secondson the first try, turn the key
to OFF, wait approximately ten (10) seconds so you do not
flood the engine, then try again.
*
[TO06520(R)01/96]
n
At temperaturesabove10ÊF(-12ÊC):If the engine does not
start infive (5) secondson the first try, turn the key to OFF,
wait approximately ten (10) seconds so you do not flood the
engine, then try again.
%*
[TO06521(R)01/96]
For a warm engine:
*
[TO06522(R)01/96]
n
Do not hold the key in the START position for more than
five (5) secondsat a time. If the engine does not start within
five (5) seconds on the first try, turn the key to the OFF
position. Wait a few seconds after the starter stops, then try
again.
*
[TO06575(R)01/96]
Whenever you start your vehicle, release the key as soon as the
engine starts. Excessive cranking could damage the starter.
File:08untor.ex
Update:Thu Mar 20 08:53:27 1997
Page 187 of 361
186
%*
[GF20600(R)01/96]
Additional Special Driving Instructions for
4-Wheel Drive Vehicle Operators
*
[GF20701(R)01/96]
Driving on Hill or Slope Terrain
[GF20800(R)03/96]
When driving on a hill, avoid driving crosswise or turning on
steep slopes; you could lose traction and slip sideways. Drive
straight up, straight down or avoid the hill completely. Know
the conditions on the other side of a hill before driving over the
crest.
*
[GF20900(R)01/96]
When climbing a steep hill, start in a lower gear, rather than
finding it necessary to downshift from a higher gear after the
ascent has started. This reduces strain on the engine and the
possibility of stalling.
*
[GF21000(R)01/96]
When descending a steep hill avoid sudden braking. Rapid
pumping of the brake pedal will help slow the vehicle and still
maintain steering control.
*
[GF21101(R)01/96]
Driving on Snow or Ice
[GF21200(R)01/96]
A four-wheel drive or all-wheel drive vehicle has advantages
over two-wheel drive vehicles in snow and ice but can skid like
any other vehicle. If so equipped, keep the vehicle in four-wheel
drive if icy or slippery conditions exist.
*
[GF21300(R)01/96]
Avoid sudden applications of power and quick changes of
direction on snow or ice. Apply the accelerator slowly and
steadily when starting from a full stop.
*
[GF21310(R)01/96]
All utility-type and Four-Wheel Drive vehicles have special
design and equipment features to make them capable of
performing in a wide variety of off-road applications. Specific
design characteristics give them higher centers of gravity than
ordinary passenger cars.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997
Page 215 of 361
214
*
[GF38800(R)03/96]
When descending a steep grade with a trailer, operate in Drive
rather than Overdrive. If additional braking is needed, shift the
automatic transmission gearshift into the 2 (Second) or 1 (Low)
position.
[GF38925(R)05/96]
Servicing Your Vehicle If You Tow
*
[GF38950(R)05/96]
If you tow a trailer for a long distance, your vehicle will need
to be serviced more frequently than usual. Refer to the
Maintenance Schedulebooklet for additional information.
[GF39000(R)01/96]
Trailer towing tips
*
[GF39100(R)01/96]
Before starting on a trip, practice turning, stopping and backing
in an area away from heavy traffic. Get to know the ªfeelº of
the vehicle/trailer combination.
*
[GF39200(R)01/96]
Practice backing up. Back up very slowly, with someone outside
at the rear of your trailer to guide you. Place your hand at the
bottom of the steering wheel and move it in the direction you
want the rear of the trailer to swing. Slight movement of the
steering wheel results in a much larger movement of the rear of
the trailer.
*
[GF39300(R)01/96]
Allow more room for stopping with a trailer attached. Trailer
brakes should be applied first, whether manually or
automatically controlled, when approaching a stop.
*
[GF39400(R)01/96]
For a good handling truck-trailer combination, the trailer tongue
load should be approximately 10-15% of the loaded trailer
weight.
*
[GF39500(R)01/96]
Make a thorough check of your equipment before starting out
on the road. After you have traveled about 50 miles (80 km)
stop in a protected area and double-check your hitch and
electrical connections. Also check trailer wheel lug nuts for
tightness.
*
[GF39600(R)01/96]
When turning, drive slightly beyond the normal turning point
so the trailer wheels will clear curbs or other obstructions.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997
Page 268 of 361
268
%*
[MC22800(R)01/96]
Power Steering Fluid
*
[MC22810(R)01/96]
Check the level of the power steering fluid at least twice a
year (i.e., every Spring and Fall).
%*
[MC22900(R)01/96]
Checking and Adding Power Steering Fluid
*
[MC22910(R)04/96]1.
Start the engine and let it run until the power steering fluid
reaches normal operating temperature. The power steering
fluid will be at the right temperature when the engine
coolant temperature gauge in the instrument cluster is near
the center of the normal operating temperature range.
*
[MC22912(R)01/96]2.
While the engine idles, turn the steering wheel back and
forth several times. Make sure that the cap assembly is
installed at this time.
*
[MC22914(R)01/96]3.
Turn the engine off.
%*
[MC22916(R)01/96]4.
Check the fluid level on the dipstick (which is highlighted in
yellow in your vehicle). The fluid level should be between
the arrows in the FULL HOT range, which is marked on the
side of the dipstick, opposite the side marked FULL COLD.
Do not add fluid if the level is within the FULL HOT range.
[MC22918(R)01/96]
10-1/2 pica
art:0021195-A
Power steering dipstick
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997
Page 270 of 361
270
[MC22936(R)01/96]
10-1/2 pica
art:0090155-A
Power steering dipstick location
*
[MC22940(R)01/96]5.
If the power steering fluid is low, add fluid in small
amounts, continuously checking the level, until you reach the
FULL HOT range. Do not overfill.
*
[MC22942(R)03/96]6.
When you are finished, put the dipstick back in and make
sure that it fits snugly.
[MC22944(R)05/96]
Use only power steering fluid that meets Ford specification such
as MERCONHMulti-Purpose ATF XT-2-QDX (or equivalent).
*
[MC22946(R)01/96]
If the power steering fluid is low, do not drive your vehicle for
a long period of time before adding fluid. This can damage the
power steering pump.
*
[MC22948(R)03/96]
If you check the power steering fluid when it is cold, make sure
that the fluid reaches the FULL COLD range on the dipstick.
The reading will only be accurate if the fluid temperature is
approximately 50 to85ÊF (10 to 30ÊC).
*
[MC22950(R)01/96]
NOTE: Do not turn the steering wheel of your vehicle with
the engine off. It could force power steering fluid out
from the reservoir cap or in extreme cases, it could
unseat the cap.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997