drain bolt FORD SIERRA 1993 2.G Fuel And Exhaust Systems Fuel Injection Workshop Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1993, Model line: SIERRA, Model: FORD SIERRA 1993 2.GPages: 16, PDF Size: 0.84 MB
Page 10 of 16
26Further refitting is a reversal of removal,
ensuring that all hoses, pipes and wiring plugs
are correctly connected.
27On completion, where applicable, check
and if necessary adjust the idle mixture.
Removal
1Disconnect the battery negative lead.
2Remove the air cleaner assembly.
3Depressurise the fuel system and
disconnect the fuel inlet pipe from the CFI unit.
4Disconnect the fuel return pipe from the CFI
unit. Be prepared for fuel spillage.
5Disconnect the throttle cable from the
linkage on the CFI unit.
6On 1.6 litre models, either partially drain the
cooling system or clamp the coolant hoses as
close as possible to the CFI unit to minimise
coolant loss, then disconnect the hoses from
the unit.
7Disconnect the wiring plugs for the throttle
position sensor, throttle valve control motor,
fuel injector and, on 1.6 litre models, the air
charge temperature sensor.
8Disconnect the vacuum pipe from the CFI
unit.9Unscrew the four (1.6 litre), or three (1.8
litre) securing bolts, and lift the CFI unit from
the inlet manifold (see illustration). Recover
the gasket.
Refitting
10Refitting is a reversal of removal, bearing
in mind the following points.
11Ensure that all mating faces are clean, and
use a new gasket.
12Top-up the cooling system.
13On completion, turn the ignition on and off
five times to pressurise the system, and check
for fuel leaks.
Refer to Chapter 1, Section 37.
1The valve is mounted at the end of the
pulse-air filter housing (see illustration).
2Disconnect the vacuum hose from the top
of the valve, then loosen the hose clips at
either end of the valve, and remove the valve.
Note the orientation of the arrow on the valve
body, which denotes the direction of flow.
3Refitting is a reversal of removal, ensuring
that the arrow on the valve body is orientated
as noted before removal.1Remove the air cleaner assembly.
2Loosen the hose clips, and disconnect the
air hoses from the check valves next to the
exhaust manifold (see illustration).
3Remove the two bolts securing the check
valve bracket to the exhaust manifold.
4Unscrew the unions securing the air tubes
to the manifold, then carefully withdraw the
tubing assembly, taking care not to distort the
tubes (see illustration).
5Refitting is a reversal of removal.
1The solenoid is located at the right-hand
side of the engine compartment.
2Disconnect the battery negative lead.
3Disconnect the vacuum pipe connector from
the pulse-air control solenoid (see illustration).
4Disconnect the solenoid wiring plug, pulling
on the plug, not the wiring.
5Unscrew the securing screw, and withdraw
the solenoid from the body panel.
6Refitting is a reversal of removal, ensuring
that the locating lug is correctly positioned,
and noting that the vacuum pipes will only fit
in one position.
23Pulse-air control solenoid
(1.6 litre CVH) - removal and
refitting
22Pulse-air delivery tubing
(1.6 litre CVH) - removal and
refitting
21Pulse-air system vacuum-
operated air valve (1.6 litre
CVH) - removal and refitting
20Pulse-air filter element (1.6 litre
CVH) - renewal
19CFI unit (1.6 and 1.8 litre (R6A
type) CVH) - removal and
refitting
4B•10Fuel and exhaust systems - fuel injection
18.23 Lifting a fuel injector from the
cylinder head21.1 Pulse air system vacuum-operated air
valve (arrowed)
23.3 Disconnect the vacuum pipe
connector from the solenoid22.4 Unscrewing a pulse-air delivery tube
union22.2 Pulse-air delivery check valves
(arrowed)
19.9 CFI unit securing bolts (arrowed) -
1.6 litre CVH
Caution: Refer to the
precautions in Section 1 before
proceeding. A new gasket must
be used on refitting.
Page 12 of 16
4Remove the three screws securing the
motor and the throttle position sensor
assembly mounting bracket to the CFI unit,
and withdraw the assembly.
5Remove the three motor securing screws,
and withdraw the motor from the bracket.
6Refitting is a reversal of removal, bearing in
mind the following points.
7Ensure that the throttle position sensor
actuating arm locates correctly on the throttle
valve spindle, and that the mounting bracket
aligns with its locating pegs.
8On completion, the idle speed should be
checked by a Ford dealer at the earliest
opportunity.
1.8 litre
9Disconnect the battery negative lead.
10Remove the air cleaner assembly.
11Disconnect the wiring connector from the
throttle valve control motor.
12Remove the three screws securing the
motor and the mounting bracket to the CFI
unit, and withdraw the assembly.
13Remove the three motor securing screws,
and withdraw the motor from the bracket.
14Refitting is a reversal of removal, ensuring
that the motor is located on the throttle
linkage, and that the bracket and locating
pegs are aligned.
Note: A tachometer and an exhaust gas
analyser will be required to check the idle
mixture on completion. A new gasket must be
used when refitting the throttle body.
2.0 litre SOHC models
1Disconnect the battery negative lead.
2Free the throttle position sensor wiring plug
from the retaining clip on the underside of the
throttle body. Disconnect the wiring plug
halves by releasing the locktabs and pulling
on the plug halves, not the wiring.
3Disconnect the throttle cable from the lever.
4Disconnect the crankcase ventilation hose
from the air inlet hose, then disconnect the air
inlet hose from the throttle body and the
airflow meter.
5Remove the four securing bolts and
withdraw the throttle body from the inlet
manifold. Recover the gasket.
6Refitting is a reversal of removal, bearing in
mind the following points.
7Ensure that all mating faces are clean, and
fit a new gasket.
8When reconnecting the air inlet hose, make
sure that the hose clips are correctly aligned,
see illustration, Section 15.
9On completion, adjust the throttle cable and
check and if necessary adjust the idle mixture.
2.0 litre DOHC models
10Disconnect the battery negative lead.
11Free the throttle position sensor wiring
plug from the retaining clip located on the
underside of the throttle body. Disconnect thewiring plug halves by releasing the locktabs
and pulling on the plug halves, not the wiring.
12Disconnect the throttle cable from the
linkage.
13Loosen the securing clip, and disconnect
the air inlet hose from the throttle body.
14Unscrew the four securing bolts, and
withdraw the throttle body from the inlet
manifold. Recover the gasket.
15Refitting is a reversal of removal, bearing
in mind the following points.
16Ensure that the mating faces of the
throttle body and the inlet manifold are clean,
and fit a new gasket.
17On completion, adjust the throttle cable.
Where applicable, check and if necessary
adjust the idle mixture.
Note: A tachometer and an exhaust gas
analyser will be required to check the idle
mixture on completion. A new gasket must be
used when refitting the manifold.
2.0 litre SOHC models
1Disconnect the battery negative lead.
2Partially drain the cooling system.
3Disconnect the crankcase ventilation hose
from the air inlet hose. Disconnect the air inlethose from the inlet manifold and the airflow
meter.
4Disconnect the HT lead from the coil, then
remove the distributor cap and position the
cap and HT leads clear of the inlet manifold
assembly.
5Unscrew the two securing bolts and remove
the throttle cable bracket (see illustration).
Disconnect the cable end from the throttle
lever, and move the bracket to one side.
6Disconnect the fuel injection harness wiring
plugs at the bulkhead end of the manifold
(see illustration).
7Disconnect the oil pressure warning lamp
switch wire from below the manifold.
8Disconnect the fuel supply hose from the
fuel rail. Loosen the union nut slowly to relieve
the pressure in the fuel system, and be
prepared for petrol spillage.
9Disconnect the fuel return hose from the
fuel pressure regulator. Be prepared for fuel
spillage.
10Disconnect the coolant hose and the
brake servo vacuum hose from the inlet
manifold.
11Unscrew the two securing nuts and
remove the bracing strut which runs from the
manifold to the right-hand side of the cylinder
head (see illustration).
12Unscrew the two bolts securing the lower
manifold bracket to the left-hand side of the
cylinder block (see illustration).
13Remove the four bolts and two nuts
securing the inlet manifold to the cylinder
head, and carefully withdraw the manifold. If
the distributor obstructs removal, extract the
front manifold stud by locking two nuts
30Inlet manifold - removal and
refitting
29Throttle body - removal and
refitting
4B•12Fuel and exhaust systems - fuel injection
30.5 Unscrew the securing bolts and
remove the throttle cable bracket
30.12 Lower inlet manifold bracket
(arrowed)30.11 Unscrew the two securing nuts
(arrowed) and remove the inlet manifold
bracing strut
30.6 Disconnecting a fuel injection harness
wiring plug
Caution: Refer to the
precautions in Section 1 before
proceeding.
Page 13 of 16
together and using them to unscrew the stud
(see illustration). Alternatively, the distributor
can be removed, although this is not
recommended unless absolutely essential.
Recover the gasket. Note that an earth strap
may be located on one of the manifold
securing bolts or studs; where applicable,
note its location as an aid to refitting.
14With the manifold removed, the various
fuel injection system components can be
separated from the manifold with reference to
the relevant Sections of this Chapter.
15Refitting is a reversal of removal, bearing
in mind the following points.
16Renew the gasket, and apply a bead of
sealant at least 5.0 mm (0.2 in) wide around
the central coolant aperture on both sides of
the gasket. Ensure that all mating faces are
clean.17Tighten the manifold securing nuts and
bolts progressively to the specified torque,
where applicable ensuring that the earth strap
is in position.
18Make sure that all hoses, cables, wires
and leads are correctly reconnected. When
reconnecting the air inlet hose, make sure that
the hose clips are correctly aligned, see
illustration, Section 15.
19On completion, refill the cooling system,
adjust the throttle cable and check and if
necessary adjust the idle mixture.
2.0 litre DOHC models
Note:New fuel injector seals must be used on
refitting.
20Disconnect the battery negative lead.
21Partially drain the cooling system.
22Disconnect the coolant hoses from the
thermostat housing and the inlet manifold.
23Disconnect the air inlet hose from the
front of the inlet manifold.
24Disconnect the breather hoses and the
vacuum hoses from the inlet manifold noting
their locations when disconnecting the brake
servo vacuum hose.
25Disconnect the throttle cable from the
throttle linkage (see illustrations).
26Disconnect the HT leads from the spark
plugs, noting their locations to aid refitting,
and move them to one side.
27Disconnect the wiring from the cooling fan
switch, the engine coolant temperature
sensor, and the temperature gauge sender.
28Release the throttle position sensor wiring
connector from the clip under the throttle body,
and separate the two halves of the connector.
29Remove the fuel injectors.
30Check that all relevant wiring, hoses and
pipes have been disconnected, to facilitate
removal of the manifold.
31Unscrew the ten bolts and two nuts
securing the inlet manifold to the cylinder
head, and carefully withdraw the manifold.
Recover the gasket.
32Recover the two plastic spark plug
spacers from the recesses in the cylinder
head (see illustration).
33If desired, the manifold can be dismantled
with reference to the relevant paragraphs of
this Chapter.
34Refitting is a reversal of removal, bearing
in mind the following points.35Ensure that the spark plug spacers are in
position in the cylinder head recesses before
refitting the manifold.
36Renew all gaskets.
37Tighten all manifold securing nuts and
bolts progressively to the specified torque.
38Make sure that all hoses, pipes and wires
are securely reconnected in their original
positions.
39On completion, refill the cooling system.
Check the adjustment of the throttle cable
and if necessary adjust the idle speed and
mixture (as applicable).1.6 and 1.8 litre (R6A type) CVH
models
40Disconnect the battery negative lead.
41Remove the air cleaner assembly.
42Depressurise the fuel system and
disconnect the fuel inlet pipe from the CFI unit.
43Disconnect the fuel return pipe from the
CFI unit. Be prepared for fuel spillage.
44Disconnect the throttle cable from the
linkage on the CFI unit.
45Partially drain the cooling system.
46Disconnect the coolant hoses from the
thermostat housing and, whereapplicable,
the CFI unit.
47Disconnect the vacuum and breather
hoses from the inlet manifold and the CFI unit,
noting their locations.
48Disconnect the wiring from the following
components, according to engine type.
Air charge temperature sensor.
Throttle position sensor.
Fuel pressure regulator/injector.
Throttle valve control motor.
Engine coolant temperature sensor.
Cooling fan switch.
Temperature gauge sender.
49Unbolt the dipstick tube from the inlet
manifold, and withdraw the dipstick and
dipstick tube from the cylinder block.
50Make a final check to ensure that all
relevant wires, hoses and pipes have been
disconnected to facilitate removal of the
manifold.
51Unscrew the seven nuts, or six securing
nuts and the single bolt, securing the inlet
manifold to the cylinder head, then lift the
manifold from the cylinder head. Recover the
gasket.
52If desired, the CFI unit can be removed
from the inlet manifold.
53If necessary, the thermostat and housing
can be removed from the manifold.
54Refitting is a reversal of removal, noting
the following points.
55Ensure that all mating faces are clean, and
renew all gaskets.
56Tighten the manifold nuts (and bolt, where
applicable) progressively to the specified
torque.
57Make sure that all wires, hoses and pipes
are reconnected as noted before removal.
58Top-up the cooling system.
59On completion, turn the ignition on and off
five times to pressurise the system, and check
for fuel leaks.
Fuel and exhaust systems - fuel injection 4B•13
4B
30.25b . . . and the throttle linkage30.32 Removing a spark plug spacer from
the cylinder head recess
30.25a Disconnect the throttle cable from
the securing bracket . . .
30.13 Where necessary use two nuts
locked together (arrowed) to remove the
front inlet manifold stud