FORD SIERRA 1993 2.G DOHC Engine Workshop Manual

FORD SIERRA 1993 2.G DOHC Engine Workshop Manual SIERRA 1993 2.G FORD FORD https://www.carmanualsonline.info/img/11/5455/w960_5455-0.png FORD SIERRA 1993 2.G DOHC Engine Workshop Manual
Trending: ECU, oil temperature, fuel tank removal, transmission, air condition, AUX, automatic transmission fluid

Page 1 of 18

FORD SIERRA 1993 2.G DOHC Engine Workshop Manual General
Engine type  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Four-cylinder, in-line, double overhead camshaft
Engine code:
Carburettor engine  . .

Page 2 of 18

FORD SIERRA 1993 2.G DOHC Engine Workshop Manual Crankshaft
Endfloat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.090 to 0.300 mm (0.004 to 0.012 in)
Main bearing running clearance . . . . . .

Page 3 of 18

FORD SIERRA 1993 2.G DOHC Engine Workshop Manual Torque wrench settingsNmlbf ft
Main bearing cap bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 to 10466 to 77
Connecting rod (big-end bearing cap) bolts:
Stage 1 .

Page 4 of 18

FORD SIERRA 1993 2.G DOHC Engine Workshop Manual Note:A hoist and lifting tackle will be
required.
1Disconnect the battery negative lead.
2Remove the bonnet.
3On carburettor models, remove the air
cleaner.
4On fuel injection models, remove the air
i

Page 5 of 18

FORD SIERRA 1993 2.G DOHC Engine Workshop Manual 34Make a final check to ensure that all
relevant wires, pipes and hoses have been
disconnected to facilitate engine removal.
35Attach a suitable hoist to the engine lifting
brackets located at the fro

Page 6 of 18

FORD SIERRA 1993 2.G DOHC Engine Workshop Manual the crossmember to the gearbox, and remove
the crossmember. Note the position of the
earth strap, where applicable. Recover the
mounting cup, and where applicable the
exhaust mounting bracket and heat

Page 7 of 18

FORD SIERRA 1993 2.G DOHC Engine Workshop Manual 1Reverse the procedure described in
paragraphs 1 to 40, Section 5,  noting the
following points.
2Before attempting to refit the engine, check
that the clutch friction disc is centralised.
3Check that

Page 8 of 18

FORD SIERRA 1993 2.G DOHC Engine Workshop Manual Dismantling 
1Refer to Chapter 2, PartA, Section 18,
paragraphs 1 to 8 inclusive.
2A suitable selection of splined and Torx
sockets will be required to remove many of
the bolts when dismantling the en

Page 9 of 18

FORD SIERRA 1993 2.G DOHC Engine Workshop Manual 6Loosen the alternator lower mounting
through-bolt, then remove the alternator
upper mounting bolt, and swing the alternator
away from the engine.
7Unscrew the central securing bolt, and
withdraw the

Page 10 of 18

FORD SIERRA 1993 2.G DOHC Engine Workshop Manual should be fitted dry. Drive in the new seal
using a suitable metal tube, making sure that
the seal lip faces into the engine, and taking
care not to damage the timing chain cover
(see illustration).
3
Page:   1-10 11-20 next >
Trending: AUX, clutch, gas mileage, wheel torque, wheel alignment, ESP, run flat