FORD SIERRA 1993 2.G Suspension And Steering Workshop Manual

FORD SIERRA 1993 2.G Suspension And Steering Workshop Manual SIERRA 1993 2.G FORD FORD https://www.carmanualsonline.info/img/11/5463/w960_5463-0.png FORD SIERRA 1993 2.G Suspension And Steering Workshop Manual
Trending: four wheel drive, wheel bolts, lock, wheel, weight, steering wheel, set clock

Page 1 of 20

FORD SIERRA 1993 2.G Suspension And Steering Workshop Manual Front suspension
Type  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Independent by MacPherson struts with coil springs and integral
telescopi

Page 2 of 20

FORD SIERRA 1993 2.G Suspension And Steering Workshop Manual Wheels
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pressed steel or alloy
Size:
Saloon, Hatchback and Estate models:
Steel . . . . . . .

Page 3 of 20

FORD SIERRA 1993 2.G Suspension And Steering Workshop Manual Torque wrench settings (continued)Nmlbf ft
P100 models:
Shock absorber-to-chassis crossmember bolt . . . . . . . . . . . . . . . . . . .60 to 7044 to 52
Leaf spring-to-front bracket bolt . . . . . . .

Page 4 of 20

FORD SIERRA 1993 2.G Suspension And Steering Workshop Manual 6Where applicable, remove the brake pipes
from the clips on the crossmember, taking
care not to strain them, and detach any cables
or electrical leads which may be secured with
clips or cable-ties, no

Page 5 of 20

FORD SIERRA 1993 2.G Suspension And Steering Workshop Manual 7Working in the engine compartment,
unscrew the strut upper mounting nut, at the
same time supporting the strut from below.
Use a 6 mm Allen key inserted in the end of
the strut piston rod to prevent

Page 6 of 20

FORD SIERRA 1993 2.G Suspension And Steering Workshop Manual 1Remove the hub carrier.
2Reverse the roadwheel nuts and screw
them fully onto the studs to protect the
threads, then mount the hub carrier assembly
in a vice as shown (see illustration).
3Prise the d

Page 7 of 20

FORD SIERRA 1993 2.G Suspension And Steering Workshop Manual Refitting
8To refit the anti-roll bar, proceed as follows.
9Fit the shallow dished washers (colour
coded black or green) and the plastic covers
(where applicable) to the ends of the anti-roll
bar, the

Page 8 of 20

FORD SIERRA 1993 2.G Suspension And Steering Workshop Manual pivot pin. Take care not to lose the
components (see illustration).
5Remove the brake cable sheaths from their
brackets on the vehicle underbody.
6Unscrew the brake pipes from the brake
hoses at the b

Page 9 of 20

FORD SIERRA 1993 2.G Suspension And Steering Workshop Manual Refitting
15Refitting is a reversal of removal, bearing
in mind the following points.
16Where applicable, secure the larger front
guide plate bolt by bending up the lockwasher
tab(s).
17Before tighten

Page 10 of 20

FORD SIERRA 1993 2.G Suspension And Steering Workshop Manual 3With an assistant supporting the shock
absorber from below, unscrew and remove
the upper mounting bolt and nut. Withdraw
the shock absorber from under the vehicle.
4Refitting is a reversal of removal
Page:   1-10 11-20 next >
Trending: ECU, weight, set clock, jack points, ABS, steering wheel, wheel bolts