steering FORD SIERRA 1993 2.G XR4 Workshop Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1993, Model line: SIERRA, Model: FORD SIERRA 1993 2.GPages: 45, PDF Size: 1.33 MB
Page 3 of 45
pC pB
pD pJ
pK
pE
pJ
pG
pI
pF
pH
Suspension - (front)0 2
pA
sway bar bushings
(see page 4)
pF Front Control Arms higher mileage cars exhibiting ball
joint and bushing wear can benefit from our standard control
arms. These arms are brand new, and include ball joints and
bushings installed.
Note: the outboard (sway/control arm) bushing
is an uprated "castellated" design which transmits less vibration
than the original U.S. spec. bushing.
(left) M428L
(right) M428R
pG
Inner Control Arm Bushing H.D. Made from
increased durometer rubber, these heavy duty (GPN) bushings
offer the desired firming effect while retaining a reasonable
degree of shock and vibration absorption. (each) M428BH-N
Optional urethane version of above bushing(set) M428BU
pH
Control Arm/Sway Bar Bushing Kit This heavy
duty urethane bushing set really does an excellent job
limiting the amount of "jutter" felt at the steering wheel
which is especially noticeable under braking. The kit includes
bushing halves and center sleeves to do both sides of the
car and is easy to install.
(set) M428BK
pH
Control Arm/Sway Bar Bushings As an option to
urethane bushings we offer either the "castellated" type
outer TCA bushings are available in standard rubber, or the
new style (better fills the void between the bushing halves)
H.D. GPN bushing kit. Both will dramatically reduce the
vibration under braking common to XR's and Scorpio's.
Outer TCA Bushings Standard (pair) does 1 armM428B
Outer TCA Bushing Set H.D. (set)M428BK-N
pI
Sway Bar Washer Get the most from your new
"castellated" type outer TCA bushings by using this "shallow"
washer (in front behind the lock nut) for a tighter fit.M407W
pJ
Tie Rod Ends High quality European Ford standard
replacement tie rod ends. (left) M434L (right) M434R
pK
Front Strut Upper Insulator H.D. Made from increased
durometer rubber, these heavy duty (GPN) Insulators offer the
desired firming effect while retaining a reasonable degree of
shock and vibration absorption. Steering and transitional
response becomes noticeably more direct.(each) M404 pA
Front Sway Bar The larger Cosworth Sierra 28.5mm
factory front sway bar is a direct replacement for the standard
25mm bar.
(H.D. bar clamp bushings are included)M407
NOTE: see price list for sway bar clamp bushings for XR & Scorpio
pB Spring Sets see page 3 (spring section) for listings
pC Front Struts (see below- shocks sold as each)
Spax TA series struts utilize a non pressurized gas over oil design
with 10 positive settings (knob type external adjustment on top) for
tuning the dampening to suit individual applications.M401A
Spax Sport One of the most popular shocks we sell, Spax fixed rate
gas sport shocks are an excellent choice for upgrading the handling
performance on the XR. M401V
Bilstein New for 2000. Bilstein's new sprint series gas shocks
offer the big B's renowned German made performance at a very
attractive price. Bilstein shocks are now available in our
suspension kits see page 3 for details.M401B
Rally/Sport Super-Gas made to European Ford spec. by Koni of
Holland. R/S shocks feature Konis twin-tube low pressure design and
have adjustable settings (knob type external adjustment on top) which
can be tailored to suit individual applications.
M401RS
Boge Turbo-Gas German manufactured twin tube high pressure
gas design utilizing a unique variable valving system that insures
the perfect balance between ride comfort and road holding
capability.M401S
DeCarbon French made mono tube high pressure gas shocks with
fairly sporty valving, similar in design to Bilstein.M401G
KYB GR2 gas struts are high quality, heavy duty units that are
a cost effective performance upgrade for the XR4. Handling is
improved without sacrificing ride quality.M401Y
pD
Steering Rack complete rack assembly w/inner tie rods,
boots, and stainless steel inner sleeve. M434SR
pE
Rack Boot* replacement steering rack boot M434RB
*same boot left or right XR4 & Scorpio
Shock Absorbers
GAS SHOCK ABSORBERSSUPER
GAS SHOCK ABSORBERScheck price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed itemscheck price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed items
check price lists for Scorpio versions of listed items
Page 5 of 45
pA Sway Bar Bushings H.D. Urethane sway bar bushings in 25mm for
standard XR4 and 28mm for larger Sierra Cosworth or Scorpio sway bars.
Note: XR4Ti and Scorpio sway bar clamps differ slightly making the bushings
non-interchangeable. XR's that require replacement bar clamps (see below) will
then require Scorpio type bushings to match. (bushings sold each)
Bar Bushing H.D. 25mm- (direct fit) XR4 M407BU
Bar Bushing H.D. 28mm- (direct fit) XR4 M407BAU
Bar Bushing H.D. 25mm- (special) XR4 with G407C clampG407BA
Bar Bushing H.D. 28mm- (direct fit) Scorpio G407BAU
pB
Sway Bar Bushing Clamps The European type sway bar bushing
clamp (used on Scorpio & Cosworth) has a groove to receive a ridge back
type bushing. Clamps are a direct replacement for Scorpio and can also be
used to replace worn or broken clamps on XR4 with correct bushings (see
above).
(2) required- sold each
Sway Bar Bushing Clamp (each)- Scorpio G407C
pC
Steering Rack Complete ZF type rack assemblies include inner tie
rods, boots, and stainless steel inner sleeve.
Steering Rack Assembly- XR4 M434SR
Steering Rack Assembly- Scorpio G434SR
Steering Rack Bushing Standard and H.D. (urethane) rack bushings
(2) required (sold each)
Steering Rack Bushing (each)- XR4 & Scorpio M434B
Steering Rack Bushing H.D (each)- XR4 & Scorpio M434BH
pD
Inner Tie Rod High quality European Ford inner tie rods available
for XR4 and Scorpio.
(sold each)
Inner Tie Rod- XR4Ti M434TK
Inner Tie Rod- Scorpio (left & right same) G434TK
pE
Rack Boot All rubber steering rack bellows (boots). Suitable for both
XR4 and Scorpio.
(left & right rack boots same- sold each)
Steering Rack Boot (each) -XR4 & Scorpio M434RB
pF Outer Tie Rod End High quality European Ford outer tie rod ends
available for XR4 and Scorpio.
(each)
Tie Rod End- XR4 (left) M434L
Tie Rod End- XR4 (right) M434R
Tie Rod End- Scorpio (left & right same) G434
pG
Power Steering Pumps Direct fit, replacement power steering
pumps for XR4 and Scorpio applications.
(core charge required)
Power Steering Pump- XR4Ti (integral reservoir type) M434P
Power Steering Pump- XR4Ti (remote reservoir type) M434PA
Power Steering Pump- Scorpio (all) G434P
pH
P/S Pressure Hose We have these hard to find pressure side hoses
available for all model year XR4Ti's.
P/S Pressure Hose- XR4Ti (all years) M434PH
pI
Strut Boot/Bump Stop These H.D. strut boot/bump stops help
reduce the chance of strut damage due to over-compression and/or strut rod/
seal damage from dirt and corrosion. A specially designed one piece bellows
with integral (NBR),"nitrile butadiene", variable rate bump rubber make these
especially well suited for lowered ride height suspensions.
(sold each)
Strut Boot/Bump Stop (each) -XR4 & Scorpio M405B
Front Strut Rotating Bearings
Upper Rotating Bearing (each) -Scorpio G403
Upper Rotating Bearing (each) -XR4M403
pF pC
pEpD
Suspension & Steering
pA/B
0 4
pI
pH pG
Page 6 of 45
Suspension Bushing Guide
FRONT BUSHINGS XR4Ti
p pp p
pA Bushing* H.D. Upper Strut Mount (GPN)M404 24.00
*bushing (1) refits 1 strut- 2 required per car
p pp p
pB Bushings* Standard Rubber Outer TCA M428B 20.00
*bushings pair (2) refits 1 arm - "castelated" type bush
p pp p
pB Bushing Set* H.D. Rubber (GPN) M428BK-N 50.00
*includes bushings, sleeves, washers & nuts- full car set left & right
p pp p
pB Bushing Set* H.D. Urethane Outer TCA M428BK 70.00
*includes bushings & sleeves - full car set left & right
p pp p
pC Bushing* Standard Inner TCA C428 9.50
*bushing each (1) refits 1 arm - 2 required per car
p pp p
pC Bushing* H.D. (GPN) Inner TCA M428BH-N 16.75
*bushing each (1) refits 1 arm - 2 required per car
p pp p
pC Bushing Set* H.D. Urethane Inner TCAM428BU 30.00
*includes bushings & sleeves- full car set left & right
p pp p
pD Bushing* Steering Rack Standard M434B 8.70
*bushing each (1) refits 1 mounting point- 2 required per rack
p pp p
pD Bushing Set* H.D. Urethane Steeing RackM434BH 30.00
*includes bushings, sleeves- full rack set left & right
p pp p
pE Bushing* Urethane Sway Bar 25mm M407BU 20.00
*bushing each (1) refits 1 mounting point- 2 required per sway bar
note: these bushings are direct fit for XR4 bushing clamps
p pp p
pE Bushing* Urethane Sway Bar 28mm M407BAU 20.00
*bushing each (1) refits 1 mounting point- 2 required per sway bar
for use only with larger Cosworth 28mm sway bar.
note: these bushings are direct fit for XR4 bushing clamps
REAR BUSHINGS XR4Ti
p pp p
pF Bushing* H.D. (GPN) Body Beam Mount M429B 36.75
*bushing each (1) 2 required per car
p pp p
pF Bushing* H.D. Urethane Body Beam MountM429BU 54.50
*bushing with sleeve each (1) 2 required per car
p pp p
pG Bushing* H.D. Urethane Inner TCA M424BI 29.75
*bushing with sleeve each (1) refits 1 arm - 2 required per car
p pp p
pH Bushing* H.D. Urethane Outer TCA M424BO 29.75
*bushing with sleeve each (1) refits 1 arm - 2 required per car
p pp p
pI Bushing* Urethane Rear Sway Bar 12MM M408BU 6.00
*bushing each (1) refits 1 mounting point- 2 required per sway bar
for use only with standard XR4 12mm sway bar.
p pp p
pI Bushing* Urethane Rear Sway Bar 16MMM408BAU6.00
*bushing each (1) refits 1 mounting point- 2 required per sway bar
for use only with larger Cosworth 16mm sway bar.
SWAY BAR
STEERING
RACKp pp p
pA
p pp p
pBp pp p
pCp pp p
pD
p pp p
pE
FRONT SUSPENSION
CONTROL ARM
p pp p
pF
p pp p
pGp pp p
pH
p pp p
pI
REAR (TRAILING)
CONTROL ARM
SWAY BAR
REAR SUSPENSION
REAR
AXLE
Standard Rubber Bushings - Stock O.E. replacement
Hard Rubber (GPN) Bushings - Similar to standard bushing
but made with higher durometer rubber, stock appearance.
H.D. Urethane Bushings - High durometer moulded urethane
product, superior quality, low noise, easy installation.
FRONT BUSHINGS SCORPIO
p pp p
pA Bushing* Standard Upper Strut MountG404 24.90
*bushing (1) refits 1 strut- 2 required per car
p pp p
pB Bushings* Standard Rubber Outer TCA M428B 20.00
*bushings pair (2) refits 1 arm - "castelated" type bush
p pp p
pB Bushing Set* H.D. Rubber (GPN) M428BK-N 50.00
*includes bushings, sleeves, washers & nuts- full car set left & right
p pp p
pB Bushing Set* H.D. Urethane Outer TCA M428BK 70.00
*includes bushings, sleeves & nuts- full car set left & right
p pp p
pC Bushing* Standard Inner TCA G428B 12.20
*bushing each (1) refits 1 arm - 2 required per car
p pp p
pC Bushing* H.D. (GPN) Inner TCA G428H-N 22.50
*bushing each (1) refits 1 arm - 2 required per car
p pp p
pC Bushing Set* H.D. Urethane Inner TCAG428BU 35.00
*includes bushings & sleeves- full car set left & right
p pp p
pD Bushing* Steering Rack Standard M434B 8.70
*bushing each (1) refits 1 mounting point- 2 required per rack
p pp p
pD Bushing Set* H.D. Urethane Steeing RackM434BH 30.00
*includes bushings, sleeves- full rack set left & right
p pp p
pE Bushing* Urethane Sway Bar 28mm G407BAU 20.00
*bushing each (1) refits 1 mounting point- 2 required per sway bar
note: these bushings are direct fit for Scorpio bushing clamps only
REAR BUSHINGS SCORPIO
p pp p
pF Bushing* H.D. (GPN) Body Beam Mount M429B 36.75
*bushing each (1) 2 required per car
p pp p
pG Bushing* H.D. Urethane Body Beam MountM429BU54.50
*bushing with sleeve each (1) 2 required per car
p pp p
pH Bushing* H.D. Urethane Inner TCA M424BI 29.75
*bushing with sleeve each (1) refits 1 arm - 2 required per car
p pp p
pI Bushing* H.D. Urethane Outer TCA M424BO 29.75
*bushing with sleeve each (1) refits 1 arm - 2 required per car
p pp p
pI Bushing* Urethane Rear Sway Bar 16MMG408BU6.00
*bushing each (1) refits 1 mounting point- 2 required per sway bar
note: these bushings are direct fit for Scorpio bushing clamps only
0 5
Page 19 of 45
Accessories
pApA
Cosworth Sierra Steering Wheel This sporty 3 spoke design
leather wrapped steering wheel is standard factory issue on the Sierra
Cosworth and RS500 models. The smaller wheel diameter (13.9 inch) helps
make the steering ratio more effective and the fatter rim grip offers both comfort
and control. Wheel is available in black and included center horn button with
Ford logo and horn symbol.M322
pB Cosworth Sapphire Steering Wheel This 3 spoke leather wrapped
wheel from the Sierra Sapphire 4x4 steering wheel is a departure on the
original Coswoth version. It's wider center spokes are positioned lower for
comfortable hand position and a better view of the instrumentation. The smaller
wheel diameter (13.9 inch) helps make the steering ratio more effective and the
fatter rim grip offers both comfort and control. Wheel is available in black and
included center horn button with Ford logo and horn symbol.M322A
Standard Horn Button for the standard XR4 steering wheel we have the
European "Ford" oval logo horn button. Just the thing for finishing the interior
off while fitting Ford logos to the exterior.
Z61551
pC Contoured Dash Overlay just the ticket for covering up a cracked
vinyl dash pads which are so common on the XR4 & Scorpio. This moulded
plastic dash overlay is simple to install and covers up a world of sin, quickly
returning the interior to its original splendor.
note: supplied in black can be easily
painted to match interior color
(for XR4) M323
NEW (for Scorpio) G323
pD White Gauge Face Set Colored gauges are quite the rage. They add
a very unique look to the interior, and are easy to read in daylight or when
illuminated at night. We have a gauge face kit that will replace the standard
(black) speedo, tach/boost, fuel and water temp, gauges and indicator lamps
with a thick self adhesive mylar faces that are white in color. These gauge
faces are manufactured specially for BAT by a original equipment instrument
supplier to Ford, GM, Vauxhall so quality is outstanding. They illuminate from
the rear "back light", just as the standard gauges, and will not opaque with age
like typical cheap reproductions will. An added benefit of our gauge face kit
is the speedo is calibrated beyond 85mph all the way to 150mph. Updating
earlier cars with 85mph speedos is a snap.
(available spring 99) M341W
pE
170 mph Speedometer For the owners of land based cruise
missiles we offer the original equipment Sierra Cosworth speedometer
calibrated in mph (170 in white) and kmph (270 in yellow) with re-setable
trip-meter. A slight bit of tweaking is required to fit.
M341A
150 mph Speedometer Sierra XR4's and later Merkurs came with a more
realistic 150 mph speedometer which easily replaces the American (only
calibrated to 85 mph) version.M341
Dash Instrument Panel Bulb lamp with (white) socketM330L
Dash Warning Lamp Bulb lamp with (gray) socketM330WL
pF Torch Key & Battery complete Ford key blank and lamp/battery.
Torch key blanks and lamp batterys are also listed separately below.
C309KL
Torch Key Blank replacement key blank for XR4 (less lamp)Z61179
pG Lamp & Battery lamp and battery for XR4 & Scorpio keysC309KLB
pH Standard Keys as an extra key or an alternative to the more bulky torch
key, this European key blank has a molded plastic grip with wide ring slot with
Ford logo.
(for Scorpio) G309K (for XR4) C309K
Hatch Lock Assembly lock assem. w/housing & 2 keysM815L
Hatch Striker commonly required replacement itemM815S
Hatch Lock Retaining Clip commonly required replacement itemM815C
Complete Car Lock Set doors, hatch, ignition w/ 2 keysM309LS
pD
pE
BRAKE
pF
pHpG pC
pB
turbo
1 8
Page 26 of 45
Turbocharger
pC
pG/H/I
pF
pD
pA
pB
pE
pA Standard Wastegate Actuator Since the stock XR
wastegate is no longer available new, we supply a high quality
re manufactured unit. Internal components (diaphragm) are re-
placed and exterior is zinc plated.) M521WR
pB
Turbochargers We offer both re manufactured stock
specification and modified high performance turbos for the
XR. High quality re manufactured turbos include; new center
cartridge compressor/turbine wheel assembly with recondi-
tioned outer compressor/turbine housings, new bearings,
seals and O-rings and fasteners. Our high performance turbo
adds a few extra tweeks. A GNX compressor wheel machined
into the stock comp housing for an additional 30% airflow and
a 360 degree thrust bearing is fitted for added durability.
Turbos are fully dressed and include wastegate actuator,
base & drain gaskets and sold on a exchange "core" basis-
outright purchase will add an additional $100.00 to the cost.
Standard Reman. Turbocharger M522TR
High Performance Turbocharger M522TM
pC
Intercooler Kit If you are looking for a large high flow
intercooler kit this is the one to have. Intercooler core mounts
ahead of the steering rack in front of the engine facing the
ground. Air is ducted up and through the core. Plumbing is kept
short and allows for a larger core than what can usually be fitted
in the bumper/grille area. Kit is complete with intercooler core
(8" x 20" x 3.5"), mounting brackets, inlet plumbing pipes &
connectors, clamps, turbo output elbow, bypass valve and
additional hardware and instructions.
M522ICpD
Adjustable Boost Valve Kit Replace the troublesome
stock boost control solenoid with this easy to adjust under hood
boost valve. This kit uses a check valve to accurately control the
boost level which allows for faster turbo spool-up (reduced lag)
over typical adjustable "bleed-off" valves. This is a low cost modifi-
cation and should be a "must have" for all XR's.
M521BV
pE
Dual Port Wastegate Actuator These are new actua-
tors which feature an adjustable length rod (set boost & pre load)
and dual vacuum ports. The dual port feature permits use of a
remote mounted boost valve (see below), but can also be used
as a replacement for stock actuator.
M521WA2
pF
Cockpit Mounted Boost Valve Remote cockpit
mounted adjustable boost valve for use with dual port wastegate
actuators (see above). Vacuum signal is regulated by the in
car mounted valve and recirculated to the dual port actuator for
precise adjustment. M521TB
pG
Turbo Oil Feed Pipe is prone to cracking/leaking and
should always be replaced when a new turbo is fitted to assure
proper oil flow. Just look inside an old one and you will see
what we mean. M522P
pH
Turbo Inlet Hose we have a version of this (discontin-
ued by Ford) hose that links the turbo outlet pipe to the throttle
body. Ours is high specification 4-ply Silicone (blue) rated to
over 600 degrees, 190 psi burst pressure- better & cheaper
than the original ! M22H
pI
Stainless Base Gasket replacement for between the turbo
base and exhaust manifold. L521GT
2 5
Page 28 of 45
Engine & Related Items
2.5mm metallic inductance EMI
suppressed conductor: with
stainless steel windings spaced
over ferrimagnetic core
substrate
serves as
strength
member for
cable assembly
ignition cables have a non-layered high strenght insulating
jacket made entirely of aerospace grade silicone rubber to
prevent swelling and splitting at extreme trmperatures
KV85 & R-100
metallic inductance EMI
suppressed conductor
pA Performance Air Filters A quick and easy performance modification
is to replace the standard air filter with a direct fit KN high performance air filter.
Merkur XR4Ti (2.3L Turbo)M22P
Merkur Scorpio (2.9L V-6)G22P
pB
High Temp Fyre Sleeve The under hood temperatures on the XR4Ti can
be quite severe. Slipping a length of fyre sleeve over critical wiring or rubber water
& A/C hoses will add an extra degree of protection. Fyre Sleeve provides radiant heat
protection up to 800 degrees. Sleeve is sold per foot and is sized by internal diameter.
Hoses or wiring can be disconnected at one or both ends then slipped through fyre
sleeve or sleeve can be un-stitched at the seam and wire tied in place.
Mylar Fyre Foil Sleeve -10 (7/8" I.D.) per foot320510
Mylar Fyre Foil Sleeve -12 (1" I.D.) per foot320512
Mylar Fyre Foil Sleeve -16 (1 1/4" I.D.) per foot320516
Mylar Fyre Foil Sleeve -20 (1 1/2" I.D.) per foot320520
pC
Engine Mount Insulators BAT has an alternative to the recently
discontinued original equipment Ford motor mounts on the XR4Ti. Simply
remove the old motor mount assemblies, discard the worn-out rubber
portion, and reuse the top and bottom metal plates with our replacement
insulators.
Note: slight modification requires 10mm holes in plates to be
increased to 12mm. Scorpio mounts are Ford mfg. direct replacements.
Engine Mount Insulator (left & right same) XR4TiM433
Engine Mount Insulator (left & right same) Scorpio-
new FordG433
pD
Transmission Mount /Insulator Rear transmission mount/insulator-
direct fit for automatic & manual Scorpio. A heavy duty version also available.
Note:
this "square" type mount can be fitted to the XR4 with special crossmember, (see
below) as the standard "round" trans. mount used on our XR4Ti's is no longer available.
Transmission Mount Insulator*- (automatic & manual) G433T
Transmission Mount Insulator H.D*.- (automatic & manual) M433TA
*can be fitted to XR4 with additional x-member (see below)
pE Transmission Crossmember Wide and narrow type transmission
tunnel crossmenbers allow the above "square" mount/insulators to be installed in
the XR4Ti. Fitting the XR with this crossmember/mount combination is a consider-
able upgrade (strength, noise, vibration) over the USA supplied "round" mount.
Crossmember* XR4 (wide) 1987-89- manual & auto M433XL
Crossmember* XR4 (narrow) 1985-86- manual & autoM433X
*for use in combination with above G433, M433 "square" type mount
pF Engine Belts H.D. Our search for the ultimate heavy duty engine
accessory v-belts lead us to the top cog "Gold Series" by Dayco. Top cog v-
belts are built to last up to 20% longer than conventional belts. A unique cogged
design increases flexibility and airflow around the belt for reduced friction and
heat. Laminated design with high temperature rated polyester cords provide
maximum tension holding (reduced slip) over the life of the belt.
Belt- XR4Ti (1985-89) W. Pump, Alt, P. Steering (2 required)M6G
Belt- XR4Ti (1986-89) A/C CompressorM6H
Belt- XR4Ti (1985) A/C CompressorM6HA
Belt- Scorpio (1988-89) Fan & Power Steering (2 required)G6G
Belt- Scorpio (1988-89) AlternatorG6GA
Belt- Scorpio (1988-89) A/C CompressorG6H
pG
Performance Ignition Wire Sets We have tried a number of
different ignition wire options on the 2.3 Turbo and 2.9L V6 engines and have
found the Magnecor brand to offer superior quality, performance, and durability.
Cables are red in color with 8mm, 8.5mm and 10mm cable diameters.
Merkur XR4Ti (2.3L Turbo)
Ignition Wire Set- (8mm w/silicone jacket and boots)L9HT
Ignition Wire Set- (8.5mm KV85 wire w/silicone jacket and boots)M9HT
Ignition Wire Set- (10mm R-100 wire w/silicone jacket and boots)M9HTR
Merkur Scorpio (2.9L V6)
Ignition Wire Set- (8mm w/silicone jacket and boots)G9HT
Ignition Wire Set- (8.5mm KV85 wire w/silicone jacket and boots)G9HT9 pG
pF
pA
Aluminized Mylar Fyre Sleeve
pB
pC pD
pE
2 7
Page 36 of 45
Price List
This catalog is viewable and
downloadable from our internet site
(www.batinc.net) you can get
catalog updates there too.
PAGE 2 front suspension & steering
Front Sway Bar- Cosworth 28mm M407 185.00
Front Strut- Spax Adjustable (each) XR M401A 165.00
Front Strut- Spax Sport- fixed rate- (each) XR M401V 99.50
Front Strut- Bilstein-Gas- (each) XR M401B 92.50
Front Strut- R/S Adjustable (each) XR M401RS 219.95
Front Strut- Koni Sport (each) Scorpio G401K 199.95
Front Strut- Boge Turbo-Gas (each) XR M401S 97.50
Front Strut- Boge Turbo-Gas (each) Scorpio G401S 101.50
Front Strut- DeCarbon Gas (each) XR M401G 145.00
Front Strut- DeCarbon Gas (each) Scorpio G401G 145.00
Front Strut- KYB GR2 (each) XR M401Y 99.50
Front Strut- KYB GR2 (each) Scorpio G401Y 99.50
Steering Rack Assembly* (XR) M434SR 349.00
Steering Rack Assembly* Scorpio G434SR 349.00
*this item requires an additional 100.00 charge refundable upon core return
Steering Rack Bushing H.D. (set) M434BH 30.00
Steering Rack Boot (left or right) XR & Scorpio M434RB 15.50
Control Arm* (left) XR M428L 75.00
Control Arm* (left) Scorpio G428L 99.50
Control Arm* (right) XR M428R 75.00
Control Arm* (right) Scorpio G428R 99.50
*NEW control arms (ball joints and bushings are installed)
Adjustable Control Arms (pair) w/bushings DISCONTINUED
Adjustable Control Arms- Race (pair) DISCONTINUED
Bushing- H.D. (GPN) Inner Control Arm (each) M428BH-N 16.75
Bushing- H.D. (GPN) Inner Control Arm (each) ScorpioG428BH-N 22.50
Bushings- Urethane Inner Control Arm (set) M428BU 30.00
Bushings- Urethane Inner Control Arm (set) Scoprio G428BU 35.00
Bushing (standard) Inner Control Arm (each) XR C428B 9.50
Bushings*- Urethane Outer Control/Sway (set) M428BK 70.00
Bushings*- H.D. (GPN) Outer Control/Sway (set) M428BK-N 50.00
Bushings*(standard) Outer Control/Sway (1 arm pair) M428B 20.00
*M428B, M428BK & M428BK-N are all suitable for Scorpio
Washer (shallow)- Sway Bar / Outer TCA (each) M407W 2.95
Tie Rod End (left) XR M434L 24.50
Tie Rod End (right) XR M434R 24.50
Tie Rod End (same L or R) Scorpio G434 27.50
Mount/Insulator -H.D. Upper Strut (each) XR M404 24.00
Upper Strut Mount/Insulator- Scorpio (each) G404 24.50
Upper Strut Rotating Bearing- Scorpio (each) G403 7.95
Upper Strut Rotating Bearing- XR4 (each) M403 9.50
PAGE 3 suspension components
Spax Sport Kit -XR M400S 495.00
Spax Sport Kit (adjustable) XR M400A 649.00
Sport Spring Set (4) front/rear (-25mm) XR M414M 189.50
Sport Spring Set (4) front/rear (-40mm) XR M414C 225.00
Sport Spring Set (4) front/rear (standard height) XR M414S 249.00
Sport Spring Set (4) front/rear (-30mm) Scorpio G414M 269.00
Front Spring Scorpio - Standard O.E. Ford (each) G414 63.65
Rear Spring Scorpio - Standard O.E. Ford (each) G415 106.40
Rear Camber Shim Kit -XR M423R 30.00
Front Upper Strut Brace (alloy) XR M403F 149.50
Rear Upper Shock Brace (alloy) XR M403R 142.50
Rear Upper Shock Brace (steel) XR M403RS 78.00
PAGE 4 suspension components
Bar Bushing H.D. 25mm- XR4 w/standard bar M407BU 20.00
Bar Bushing H.D. 28mm- XR4 w/Cosworth barM407BAU 20.00
Bar Bushing H.D. 25mm- XR4 w/ std. bar & G407C clampG407BA 20.00Bar Bushing H.D. 28mm- ScorpioG407BAU 20.00
Front Sway Bar Clamp- Scorpio (each) M407C 7.50
Steering Rack Assembly* XR M434SR 349.00
Steering Rack Assembly* Scorpio G434SR 349.00
*this item requires an additional 100.00 charge refundable upon core return
Steering Rack Bushing (each) M434B 8.70
Steering Rack Bushing H.D. (each) M434BH 20.00
Inner Tie Rod -XR4 M434TK 51.00
Inner Tie Rod -Scorpio G434TK 51.00Steering Rack Boot (left or right) XR & Scorpio M434RB 16.75
Outer Tie Rod End (left) XR M434L 24.50
Outer Tie Rod End (right) XR M434R 24.50
Outer Tie Rod End (same L or R) Scorpio G434 27.50
Power Steering Pump XR4Ti* (integral reservoir) M434P 135.00
Power Steering Pump XR4Ti* (remote reservoir) M434PA 136.00
Power Steering Pump Scorpio* G434P 136.00
*this item requires an additional 25.00 charge refundable upon core return
P/S Pressure Hose XR4Ti M434PH 58.33
Strut Boot/Bump Stop (each) XR & Scorpio M405B 19.00
Strut Insulator/Bearing Kit XR4 (does 1 side) M403K 7.00
Upper Rotating Bearing XR4 (each) M403 8.50
Upper Rotating Bearing Scorpio (each) G403 7.95
PAGE 5
Pricing is listed with part numbers on this pages
PAGE 6
rear suspension
Rear Sway Bar w/bush- Cosworth 16mm (XR4) M408 99.50Rear Sway Bar w/bush- Cosworth 18mm (Scorpio only)G408 89.95
Rear Bar End Shackle (each) -XR M408S 15.00
Rear Bar End Shackle (each) -Scorpio G408S 15.00
Rear Bar Bush(12mm) urethane (each) stock XR4 M408BU 6.00
Rear Bar Bush (16mm) urethane (each) Cosworth M408BAU 6.00
Rear Bar Bush (16mm) urethane (each) Scorpio G408BU 6.00
Rear Control Arm Set -H.D. Competition M424 675.00
Bushing*- Urethane Outer Control Arm (each) M424BO 29.75
Bushing*- GPN Outer Control Arm (each) M424BO-N 30.50
Bushing*- GPN Body Beam Mount (each) M429B 36.75
Bushing*- Urethane H.D. Body Beam Mount (each) M429BU 54.50
Bushing*- Urethane Inner Control Arm (each) M424BI 29.75
*above bushings also Scorpio suitable
Beam/Subframe Assembly -H.D. CompetitionDISCONTINUED
Rear Shock- Spax Adjustable (each) XR M402A 89.00
Rear Shock- Spax Adjustable (each) Scorpio G402A 105.50
Rear Shock- Spax Sport- fixed rate- (each) XR M402V 75.00
Rear Shock- Bilstein- Gas (each) XR M402B 73.00
Rear Shock- Koni R/S Adjustable (each) XR M402RS 99.50
Rear Shock- Koni Sport (each) Scorpio G402K 122.85Rear Shock- Boge Turbo-Gas (each) XR M402S 75.50
Rear Shock- Boge Turbo-Gas (each) Scorpio G402S 62.50
Rear Shock- DeCarbon-Gas (each) XR M402G 63.00Rear Shock- DeCarbon-Gas (each) Scorpio G402G 87.00
Rear Shock- KYB (each) XR M402Y 46.50
Rear Shock -KYB (each) Scorpio G402Y 46.50
IMPORTANT PRICE LIST NOTES:
(1) Scorpio versions of listed XR4 parts will generally
appear below XR4 item in
italics.
(2) Items that apply for both XR4 & Scorpio are noted.
(3) Fitment notes, and core charge information is also
italicized.
(4) Additional items that do not appear in the literature
can be found in with the corresponding category /
page number reference. These listings are also
italicized.
3 503/11/02
Page 39 of 45
Price List
PAGE 18 accessories
Cosworth Steering WheelDISCONTINUED
Cosworth Sapphire Steering WheelDISCONTINUED
Horn Button Center Z61551 24.00
Dash Cover/Overlay -XR4 M323 99.50
Dash Cover/Overlay -Scorpio G323 131.25
White Gauge Face Set 150mph M341W 109.00
Speedometer 170 mph
DISCONTINUED
Speedometer 150 mphDISCONTINUED
Bulb- Dash Instrument (each) M330L 3.43
Bulb- Dash Waring Lamp (each) M330WL 1.55
Torch Key Blank & Battery C309KL 14.25
Torch Key Blank & Battery -Scorpio G309KL 15.70
Torch Key Blank- XR Z61179 6.50
Torch Key Blank- Scorpio Z64948 7.50
Lamp & Battery- XR4 & Scorpio C309KLB 10.10
Standard Key- XR C309K 6.25
Standard Key -Scorpio G309K 7.50
Rear Hatch Lock Assembly (w/ 2 keys) M815L 46.10
Rear Hatch Striker M815S 7.45
Hatch Lock Retaining Clip M815C 1.15
Car Lock Set (doors, hatch, ignition w/ keys) XR4M309LS 98.50
Car Lock Set (doors, hatch, ignition w/ keys) ScorpioG309LS 98.50
PAGE 19 accessoriesWindshield Wiper Headlamp Switch (Stalk)- XR4 M304 104.90
Turn Signal Flash/Hazard Switch (Stalk)- XR4 M305 92.50
Fuse Box Cover- XR4 M474 19.75
Door Post Black-Out Trim (left) M340TL 29.95
Door Post Black-Out Trim (right) M340TR 29.95
Pedal Pad- Accelerator XR & Scorpio M365A 5.95
Pedal Pad- Clutch XR & Scorpio M365C 5.95
Pedal Pad- Brake (manual) XR & Scorpio M365B 5.95
Pedal Pad- Brake (automatic) XR & Scorpio M365BA 6.49
Rear Hatch Lift Strut (each)- XR4 M308 30.00
Rear Hatch Lift Strut (each)- Scorpio G308 31.50
Rear View Day/Night Mirror- XR4 & Scorpio C339 41.50
Replacement Stick-on Pad for Rear View Mirror M339S 3.89
PAGE 20
books
The Sporting Fords- Sierra M207 27.50
High Performance Sierras & Merkurs M206 24.75
Classics in Color- Ford Sierra Cosworth M203 23.50
European Sierra Workshop Manual M204 32.00
European Sierra XR4i 2.8L Workshop Manual M204A 32.00
European Scorpio/Granada Workshop Manual G204 34.00
Tuning/Building Ford V6 Engines G202 17.50
Workshop Manual- Sierra/Ecsort Cosworth (2 volumes) M202 100.00
The Complete 2.3 Turbo EEC-IV Handbook M209 13.00
How to Prepare the Sierra for Motorsport M205 22.50
OTHER FORD CAR & ENGINE RELATED BOOKS & MANUALS
Workshop Manual- Fiesta 1.6L C204 20.00
Workshop Manual- Escort 1.6/1.9L E204A 12.50
Tuning/Building Ford "KENT" Series Engines F202 29.50
Building Formula Ford 1600 Engines F203 32.00
Tuning/Building Ford 2.0 SOHC and DOHC Engines S202 25.75
Tuning/Building Ford V6 Engines G202 17.50
Workshop Manual- Pinto/Bobcat 2.0/2.3L S203 12.50
2000 OHC "Pinto" Engine Performance S204 27.95
Workshop Manual- Capri MK1 2.6/2.8L V6 S205 12.50
10/15/013 8
PAGE 21 cooling system (XR4)
Hose- heater valve to pipe (to oil cooler) M421HC 16.50
Hose- heater valve to heater core M421H 8.90
& pipe (front) to thermo housing
Hose- heatervalve to pipe (upper @ rear) M421HB 10.50
& oil cooler to pipe
Heater Valve- XR & Scorpio M421V 59.00
Hose- water pipe to oil cooler-over v. cover M421HE 29.00
Hose- oil cooler to intake mfld. M421HD 7.95
Oil Cooler AWC1 110.00
Hose- pipe @ front to water pump M421HA 11.50
Hose- pipe @ front to thermo housing M421H 8.90
Thermostst Housing- H.D. cast iron L2F 22.50
Water Pump (new) L6A 73.10
Water Pump (recon) L6AR 35.00
Hose- radiator lower 85-88(MT & auto) M421BH 29.00
Hose- radiator lower 1989 (MT & auto) M421BH9 41.00
Hose- radiator upper 85-88 (MT & auto) M421TH 18.50
Hose- radiator upper 1989 (MT & auto) M421TH9 49.00
Hose- expansion tank (top fitting) tovalve cover pipe M421TT 11.45
Coolant Tank1985-88* (with level sensor bung) M421E 49.75
Coolant Tank 1989* (without sensor bung) M421E9 55.25
*coolant tanks require Scorpio thread-on cap use G421C
Coolant Tank Thread-on Cap (for above tanks) G421C 7.35
Water Level Sensor (in radiator surge tank) XR4 M421LS 40.25
Tank Gromet, Spacer Ring, Lock Collar ( for above sensor)M421SK 9.40
Hose- expansion tank (middle fitting) to radiator M421TM 11.50
Hose- expansion tank (lower fitting) to radiator drain lineM421TL 29.00
Hose- expansion tank to W/Pump (automatic "Y" hose) M421Y 45.00
Radiator XR4Ti- 85-88 (MT) M421R 250.00
Radiator XR4Ti- 1989 (MT) M421R9 295.00
Radiator XR4Ti- 85-88 (Auto) M421RA 260.00
Radiator XR4Ti- 1989 (Auto) M421R9A 329.00
Mount/Bushing (radiator top) M421RM 7.20
Electric Fan 16" (puller) A16F-PL 89.00
Thermostatic Fan Relay (170-210f adjustable) AFTR1 55.00
Blower Motor & Fan- A/C & heater M470A 174.50
Heater Core M471 89.50
Hose- Hi-temp silicone (1 foot length- makes 3 hoses)M421WT 7.00
Hose- Lower drain pipe @ radiator lower (MT)M421HF 8.50
PAGE 22 cooling system (Scorpio)
Hose- heater valve (out) to core G421HA 8.90
Hose- heater valve to engine G421HB 17.50
Hose- heater valve (inlet) to core G421HC 13.95
Hose- heater valve to pipe G421HD 18.75
Radiator (automatic) G421RA 289.00
Radiator (manual) G421R 289.00
Hose- tank to thermstat housing G421HF 11.20
Hose- upper radiator G421TH 35.00
Hose- tank to water pump G421HH 24.49
Water Pump (new) G421 94.25
Water Pump (recon) G421A 64.50
Hose- bypass/ water pump outlet to inlet mfld. G421HP 14.10
Hose- lower radiator G421BH 28.35
Hose- lower radiator (late 89) w/tee off hose G421BH-9 35.75
Hose- to oil cooler pipe G421HK 17.90
Hose- oil cooler pipe to oil cooler G421HL 9.90
Coolant Tank (late style 6-88>2-92) rectangular shapeG421TL 46.00
Coolant Tank (early style > 6-88) curved sideG421TE 46.00
Coolant Tank Cap (thread-on) Scorpio & late XR4 G421C 7.35
Oil Cooler AD1000 110.00
Heater Control Valve- XR4 & Scorpio M421V 59.00
Heater Core- Scorpio M471 89.50
Mechanical Fan Clutch Assy G422 195.00
Electric Fan 16" (puller) A16F-PL 89.00
Thermostatic Fan Relay (170-210f adjustable) AFTR1 59.00
Blower Motor & Fan- A/C Heater (Scorpio) G470H 230.00
Page 40 of 45
Price List
PAGE 23 cooling system (Scorpio)
Hose- heater valve (out) to core G421HA 8.90
Hose- heater valve to engine G421HB 17.50
Hose- heater valve (inlet) to core G421HC 13.95
Hose- heater valve to pipe G421HD 18.75
Heater Control Valve- XR4 & Scorpio M421V 60.00
Hose- coolant pipe to oil cooler from heat valve G421HL 9.90
Oil Cooler- oil to water heat exchanger AD1000 110.00
Hose- oil cooler to coolant pipe G421HM 14.40
Hose- coolant pipe from oil cooler to water pump G421HK 17.90
Hose- bypass/ water pump outlet to inlet mfld. G421HP 14.10
Hose- upper radiator (late 89) w/vent G421TH-9 35.00
Hose- coolant tank to thermo housing G421HF-9 16.45
Tank Lever Sender M421LS 40.25
Lever Sender Install Kit M421SK 9.40
Cap/Plug- Rubber G421P 2.50
Hose- lower radiator (late 89) w/tee off hose G421BH-9 35.75
Coolant Tank (6/88>89) Oval TypeG421T 52.00
Coolant Tank (late style 6-88>2-92) rectangular shapeG421TL 46.00
Radiator Cap (thread-on) Scorpio & late XR4 G421C 7.35
PAGE 24 A/C system
Evaporator- (XR4 & Scorpio) M470E 245.75
Expansion Valve - (XR4 & Scorpio) M470EV 46.50
Blower Motor - (XR4)
O.E. FordM470A 198.00
Blower Motor - (Scorpio)
O.E. FordG470A 230.00
Refrigerant Hoses*- (XR4Ti only) M470H 149.00
Refrigerant Hoses*- (Scorpio) G470H 129.00
*this item requires an additional 100.00 charge refundable upon core return
Compressor- (XR4 & Scorpio) includes clutchM470C 429.00
Clutch Assembly*- (XR4 & Scorpio) M470CL 157.50
*this item requires an additional 25.00 charge refundable upon core return
Condenser- (XR4) M470D 335.00
Condenser- (Scorpio) G470D 335.00
Electric Condenser Fan- 16" Pusher (XR4 & Scorpio)A16F-PU 89.00
Fan Mounting Tie Set (for above fan)ABKT1 7.95
Pressure Switch-
(XR4 & Scorpio) O.E. Ford DISCONTINUED
Receiver/Dryer- (XR4 & Scorpio) M470R 108.00
Receiver/Dryer- (XR4 & Scorpio) O.E. Ford M470R-F 131.50
PAGE 25 turbo components
Wastegate Actuator* -Reman. M521WR 95.00
*this item requires an additional 30.00 charge refundable upon core return
Turbo/Reman* (specify auto or 5-speed) M522TR 425.00
Performance Turbo* M522TM 649.00
*this item requires an additional 100.00 charge refundable upon core return
Intercooler Kit M522IC 1195.00
Adjustable Boost Kit M521BV 48.00
Wastegate Actuator (adjustable rod- dual port) M521WA2 119.00
Cockpit Mount Adjustable Boost Kit (remote valve) M521TB 74.50
Turbo Oil Feed Pipe M522P 19.00
Turbo Inlet Hose (45 degree elbow) M22H 44.50
Turbo Base Gasket L521GT 8.75
02/05/023 9
PAGE 26 engine & related
Main Bearing Set (STD) L16A 32.65
Main Bearing Set (+.010") L16B10 32.65
Main Bearing Set (+.020") L16B20 32.65
Main Bearing Set (+.030") L16B30 32.65
Rod Bearing Set (STD) L16H 16.35
Rod Bearing Set (+.010") L16110 16.35
Rod Bearing Set (+.020") L16120 16.35
Rod Bearing Set (+.030") L16130 16.35
Cam Bearing Set L16M 18.50
Cam Bearing Set- grooved L16MA 18.50
Aux. Shaft Bearing L5DC 10.50
Connecting Rod Bolt Set H.D. (standard 2.3 rod) L4FS 44.30
Connecting Rod Bolt Set H.D. (5.7" Chevy rod) L4FSC 35.00
Head Stud Set H.D. L2DS 98.40
Main Stud Set H.D. L2KS 89.20
Full Gasket Set (complete engine) Felpro L15AA 95.00
Top End Gasket Set Felpro L15BA 55.50
Bottom End Gasket Set (block, crank & sump) Felpro L15CA 40.10
Pan Set- sump rails & seals (cork) L15CP 22.05
Head Gasket H.D. (Ford Motorsport turbo style) L15D 16.00
Head Gasket H.D.- Felpro L15DA 19.50
Head Gasket Competition (extreme duty racing gasket)L15DR 29.50
Head Space Shim .020" L15DS 17.85
Valve Cover Gasket (standard cork) L15E 6.75
Valve Cover Gasket H.D. 2300 (hi-temp rubber)L15EA 24.00
Valve Cover Gaskets H.D. 2.9L V6 (hi-temp rubber)G15EA 15.50
Intake Manifold Gasket Set L15FA 11.40
Water Outlet Gasket (thermostat housing) L15N CALL
Water Pump Gasket (pump to block) L15P CALL
Crankshaft Rear Seal L15Q CALL
Camshaft Seal L15R 8.25
Auxiliary Shaft Seal L15S 9.25
Crankshaft Front Seal L15T 16.08
Inlet Hose- Turbo to T.Body (silicone blue) M22H 45.00
Performance Exhaust System 3" (full system) M522 705.00
Performance Exhaust System 2.5" (down pipe w/cat back)M522B 425.00
Exhaust Down Pipe 3" M522DP 159.00
Exhaust Manifold (standard cast Fomoco) M521 185.00
Exhaust Header 2.3 Turbo (tubular stainless steel) L521T 595.00
Gasket- turbocharger to manifold (stainless) L521GT 8.75
Exhaust Hanger (rubber donut) each C522H 5.25
PAGE 27
engine & related
Air Filter- XR4Ti (2.3L Turbo) M22P 35.10
Air Filter- Scorpio (2.9L V-6) G22P 50.00
Mylar Fyre Foil Sleeve -10 (7/8" I.D.) per foot 320510 4.55
Mylar Fyre Foil Sleeve -12 (1" I.D.) per foot 320512 4.90
Mylar Fyre Foil Sleeve -16 (1 1/4" I.D.) per foot 320516 5.64
Mylar Fyre Foil Sleeve -20 (1 1/2" I.D.) per foot 320520 6.32
Motor Mount Insulator (left or right same) XR- each M433 99.50
Motor Mount Insulator (L or R same) Scorpio- each G433 69.45
Transmission Mount/Insulator- Scorpio G433T 39.50
Transmission Mount/Insulator H.D. M433TA 53.00
Trans Crossmember XR (wide) 87-89 manual & auto
DISCONTINUED
Trans Crossmember XR (narrow) 85-86 manual & autoDISCONTINUED
Belt- XR4Ti (1985-89) W. Pump, Alt, P. SteeringM6G 11.90
Belt- XR4Ti (1986-89)
A/C Comp.M6H 9.50
Belt- XR4Ti (1985)
A/C Comp.M6HA 9.50
Belt- Scorpio (1988-89)
Fan & Power SteeringG6G 14.20
Belt- Scorpio (1988-89)
AlternatorG6GA 12.65
Belt- Scorpio (1988-89)
A/C Comp.G6H 10.25
Ignition Wire Set- XR4Ti (8mm ) L9HT 39.95
Ignition Wire Set- XR4Ti (8.5mm KV85 wire) M9HT 69.50
Ignition Wire Set- XR4Ti (10mm R-100 wire) M9HTR 79.00
Ignition Wire Set- Scorpio (8mm) G9HT 50.75
Ignition Wire Set- Scorpio (8.5mm KV85 wire) G9HT9 88.75