brake FORD WINDSTAR 1996 1.G User Guide

88
% [LG10971(ALL)02/95]
Anti-lock Brake System (ABS) Warning Light
*
[LG10975(ALL)12/93]
To check the anti-lock brake warning light, turn the ignition key
to the ON position. The ABS warning light should glow
momentarily.
*
[LG10981(ALL)10/93]
NOTE: If it does not glow at all or stays on for a long time,
have your vehicle's electrical system checked
immediately.
[LG10985(ALL)11/93]
6 pica art:0050147-B
The anti-lock brake warning light
*
[LG10991(ALL)05/95]
RWARNING
If the anti-lock brake system warning light remains on or
comes on while driving, have the braking system checked
by a qualified service technician as soon as possible.
[LG10995(ALL)06/95]
NOTE: If a fault occurs in the anti-lock system, and the brake
warning light is not lit, the anti-lock system is
disabled but normal brake function remains
operational.
File:wnlgs.ex
Update:Tue Mar 19 08:25:03 1996

Warning Lights and Gauges
91
% [LG11255(ALL)03/94]
Low Windshield Washer Fluid Level Warning Light
[LG11257(ALL)11/93]
This light indicates that the level of your washer fluid is low,
and you have to add more fluid. This light comes on briefly
after you turn your ignition key from the START to the ON
position. If the washer fluid is low, a one second chime will
sound and the light will remain on for 60 seconds. If the washer
fluid is not low, the light should turn off a few seconds after
the engine has started. The light and chime also come on if the
washer fluid is low when you use your windshield washers.
[LG11258(ALL)03/94]
The washer fluid is only checked when the engine is started or
the windshield washers are in operation. The light will not
come on if the fluid level becomes low while you are driving
unless you turn on the windshield washers.
[LG11260(ALL)12/93]
6 pica art:0050062-B
The low windshield washer indicator light
*
[LG11265(ALL)06/95]
Speed Control Indicator
[LG11270(ALL)05/95]
A SPEED CONTROL light is displayed in the optional electronic
instrument cluster when the speed control system is engaged.
The display will turn off when the brake pedal is pressed or if
speed control is shut off.
*
[LG11275(ALL)05/95]
This display does not indicate any problems with the speed
control, but is simply a convenient way of knowing when it is
active.
File:wnlgs.ex
Update:Tue Mar 19 08:25:03 1996

102
% [LG18500(ALL)06/94]
Auxiliary Warning Module (If equipped)
[LG18600(ALL)06/94]
An additional bank of indicator and warning lights is located
above the driver's side vent, just to the right of the steering
wheel. The light(s) located in this module are described and
illustrated below.
[LG18700(ALL)04/95]
13-1/2 pica art:0050122-F
The auxiliary warning module
% [LG18710(ALL)05/95]
Traction Control Active Light
[LG18720(ALL)04/95]
This light comes on when the Traction Control system begins
applying and releasing the brakes and adjusting the engine
characteristics to limit a wheelspin condition. You may feel
some steering changes and hear some noise, but this is normal.
[LG18730(ALL)04/95]
one inch art:0050274-AFile:wnlgs.ex
Update:Tue Mar 19 08:25:03 1996

Warning Lights and Gauges
103
[LG18740(ALL)04/95]
The Traction Control light will stay on for a minimum of four
seconds.
[LG18750(ALL)06/95]
Check Traction Assist Light
[LG18760(ALL)04/95]
This light comes on when the Traction Control system is not
operating. In some conditions, you may want to turn Traction
Control off, such as when rocking your vehicle out of deep
snow or mud.
[LG18770(ALL)04/95]
one inch art:0050275-A[LG18780(ALL)04/95]
Traction Control will automatically turn off to prevent the
brakes from overheating. The system will turn back on once the
brakes have cooled down.
[LG18790(ALL)04/95]
NOTE: If the TRAC OFF light is flashing repeatedly, it means
that there is a Traction Control system malfunction
and the system is inoperative. Contact your dealer for
service as soon as possible.
File:wnlgs.ex
Update:Tue Mar 19 08:25:03 1996

122
*
[IP12541(ALL)02/93]
To maximize fog lamp bulb life it is recommended that the fog
lamp switch be turned off after each use prior to turning off the
headlamps.
*
[IP12544(ALL)10/94]
n
To turn the fog lamps on, push the switch. An indicator light
will glow when the lamps are on.
*
[IP12547(ALL)10/94]
n
To turn off, push the switch again.
%*
[IP12550(ALL)03/95]
ªHeadlamps Onº Alert Chime
[IP12601(ALL)03/94]
The ªheadlamps onº alert chime acts as an indicator that you
have left the headlamps or parking lights on. This continuous
chime will activate when the following conditions are present:
[IP12620(ALL)03/94]
n
The headlamp and/or parking lamps are on
[IP12640(ALL)03/94]
n
There is no key in the ignition
[IP12660(ALL)05/94]
n
The driver's door is ajar (open)
%*
[IP12700(ALL)01/93]
Daytime Running Light (DRL) System
(Canadian vehicles only)
*
[IP12800(ALL)03/95]
The Daytime Running Light (DRL) system is designed to turn
the high beam headlamps on, with a reduced light output and
without illuminating the high beam indicator lamp in the
instrument panel. The DRL system operates when all of the
following conditions are met:
*
[IP12900(ALL)01/93]
n
the vehicle is ªrunningº
*
[IP13000(ALL)01/93]
n
the vehicle has a fully released parking brake
*
[IP13100(ALL)01/93]
n
the headlamp system is in the OFF position
*
[IP13200(ALL)01/93]
NOTE: You may notice that the lights flicker when the engine
is turned on or off. This is a normal condition.
File:wnips.ex
Update:Tue Mar 19 08:23:17 1996

Steering Column Controls
135
[SC04415(ALL)09/93]
13-1/2 pica
art:0050017-A
The horn pad
%*
[SC04610(ALL)04/95]
Hazard Flasher Switch
*
[SC04620(ALL)04/95]
The hazard flasher is used to alert other drivers to hazardous
situations.
*
[SC04630(ALL)09/93]
The hazard flasher switch operates the same lamps as the turn
signal lever. When the hazard flasher is activated, all of these
lamps will flash on and off. The turn signal indicators cannot be
used when the hazard lamps are flashing. Operation of the
hazard flashers does not affect operation of the brakelamps.
*
[SC04640(ALL)12/93]
The flashers work even with the key out of the ignition. The
flashers will work for up to two hours when the battery is fully
charged and in good condition. They will not drain the battery
excessively. If the flashers run for longer than two hours or if
your battery is not fully charged, your battery may be drained
to the point where the vehicle will not start.
[SC04650(ALL)09/93]
The hazard flasher switch is located on top of the steering
column.
File:wnscs.ex
Update:Tue Mar 19 08:22:27 1996

140
%*
[SC09400(ALL)01/95]
Resetting the Speed Control
*
[SC09410(ALL)03/95]
To reset the speed control to alower speed, use one of the
following procedures:
*
[SC09415(ALL)03/95]
n
COASTÐ Press and hold the COAST switch. Release the
switch when the vehicle slows down to the desired speed.
*
[SC09420(ALL)03/95]
n
Lightly tap the brake pedal. When the vehicle attains the
desired speed, press the SET ACCEL switch and release it
immediately.
[SC09425(ALL)04/95]
n
TAP-DOWNÐ Press and then quickly release the COAST
switch. Each time you ªtapº the switch, the set speed will
decrease by 1 mph (1.6 km/h). Multiple taps will cause the
set speed to decrease in increments of 1 mph (1.6 km/h).
For example, if the current set speed is 60 mph (97 km/h) 5
taps of the COAST switch will decrease the vehicle speed
and SET it at 55 mph (88 km/h).
*
[SC09430(ALL)04/95]
If vehicle speed is reduced below 30 mph (50 km/h) by any of
the above methods, then you must manually accelerate to a
speed over 30 mph (50 km/h) and reset the system.
*
[SC09435(ALL)03/95]
To reset the speed control toa higher speed, follow one of
these procedures:
*
[SC09440(ALL)03/95]
n
ACCELÐ Press and hold the SET ACCEL switch. Release
the switch when the vehicle has accelerated to the desired
speed.
*
[SC09445(ALL)03/95]
n
Depress the accelerator pedal. When the vehicle attains the
desired speed, press the SET ACCEL switch and release it
immediately.
File:wnscs.ex
Update:Tue Mar 19 08:22:27 1996

Steering Column Controls
141
[SC09450(ALL)04/95]
n
TAP-UPÐ Press and then quickly release the SET ACCEL
switch. Each time you ªtapº the switch, the set speed will
increase by 1 mph (1.6 km/h). Multiple taps will cause the
set speed to increase in increments of 1 mph (1.6 km/h). For
example, if the current set speed is 55 mph (88 km/h), five
taps of the SET ACCEL switch will increase the vehicle
speed and set it at 60 mph (97 km/h).
[SC10525(ALL)04/95]
To Cancel or Turn Off Speed Control
[SC10530(ALL)05/95]
The speed control can be cancelled at any time by depressing
the brake pedal slightly. After cancelling, you can return to the
speed you set by pressing the RESUME switch, or set a new
speed by pressing the SET ACCEL or COAST switch.
[SC10550(ALL)03/94]
Speed control can also be cancelled when you press the OFF
switch. The speed control system will remain off until you press
the ON switch and reset the speed control.
*
[SC10700(ALL)04/95]
In addition, the speed control is turned off each time you turn
the vehicle off.
%*
[SC10900(ALL)03/95]
Resuming a Set Speed
*
[SC11000(ALL)07/94]
If you press the brake pedal, the speed control is cancelled. You
can return to the speed you set by using the RSM switch, as
long as you did not press the OFF switch.
*
[SC11200(ALL)05/95]
To resume the speed you had before, you must be driving at
least 30 mph (50 km/h).
*
[SC11300(ALL)11/94]
Press and release the RESUME switch. Your vehicle gradually
returns to the previously set speed and then maintains it.
File:wnscs.ex
Update:Tue Mar 19 08:22:27 1996

142
%[SC11400(ALL)05/95]
Speed Control Light (Electronic Cluster Only)
*
[SC11500(ALL)03/95]
This light comes on when you turn on the speed control system
and set the speed. The light will be on whenever the speed
control is set, even if you override the set speed by pressing the
accelerator pedal or by pressing the coast button. The light will
go off when the brakes are used or the speed control system is
turned off.
[SC11600(ALL)11/93]
This light comes on briefly during the display self-test every
time you turn your ignition key to the ON position. The light
will go off when the key is turned to the START position. The
light should stay off when the self-test is done.
*
[SC11700(ALL)05/95]
This light does not indicate any problems with the speed control
system, but is a convenience to tell you when the speed control
system is actively maintaining a set speed.
File:wnscs.ex
Update:Tue Mar 19 08:22:27 1996

Features
155
[FV09540(ALL)05/95]
n
the ignition key is turned to the ON position
[FV09545(ALL)05/95]
n
the brake pedal is pressed
[FV09550(ALL)05/95]
n
you shift through R (Reverse)
[FV09555(ALL)05/95]
n
the brake pedal is released
[FV09560(ALL)05/95]
The Autolock feature will repeat when:
[FV09565(ALL)05/95]
n
a door is opened and then all doors and the liftgate are
closed
[FV09570(ALL)05/95]
n
the brake pedal is released
[FV09575(ALL)05/95]
On vehicles with Keyless Entry, you can deactivate the system
by using the buttons for the keyless entry system if you do not
want to use the Autolock feature.
[FV09580(ALL)05/95]
The doors may not lock automatically at the correct time if the
driver:
[FV09585(ALL)05/95]
n
shifts through gears without pressing the brake
[FV09590(ALL)05/95]
n
shifts through gears quickly after starting the vehicle
[FV09595(ALL)05/95]
n
releases their foot from the brake while someone has stepped
out of the vehicle for a moment
[FV09600(ALL)05/95]
To deactivate the Autolock system:
[FV09605(ALL)05/95]1.
Enter your permanent five-digit entry code (not the user
code you may have set).
[FV09610(ALL)05/95]2.
Within five seconds, press and hold 7/8.
[FV09615(ALL)05/95]3.
Within five more seconds, press and release 3/4.
[FV09620(ALL)05/95]4.
Release 7/8.
[FV09625(ALL)05/95]
To reactivate the Autolock system, simply repeat the instructions
for deactivating the system. By re-entering the code that
deactivates the Autolock, the keyless entry system reinstates the
Autolock feature.
File:wnfvs.ex
Update:Tue Mar 19 08:21:54 1996