brake FORD WINDSTAR 1996 1.G Owner's Guide

246
*
[DR09500(ALL)07/93]
For example, even with anti-lock brakes, extreme braking can
make it difficult to control the direction of the vehicle. Use a
ªsqueezeº technique. Push on the brake pedal with steadily
increasing force. This allows the wheels to brake, yet continue to
roll so that you may steer in the direction you want to travel.
*
[DR09600(ALL)01/93]
If you release the accelerator abruptly or brake hard while
going too fast around a severe curve, your vehicle may change
its direction of travel. Avoid applying the brakes, if possible. If
you must apply the brakes, use the ªsqueezeº technique
described earlier.
*
[DR09700(ALL)02/95]
Wheel Spin
[DR09800(ALL)05/95]
Extreme acceleration can cause the front wheels to spin,
resulting in reduced steering control. If the wheels spin during
vehicle start-up, shift to 2 (Second) gear. Move forward slowly
and evenly. If this does not work, try rocking the vehicle.
%*
[DR09900(ALL)01/93]
Driving at High Speeds
*
[DR10000(ALL)05/95]
RWARNING
Driving too fast for conditions creates the possibility of
loss of vehicle control. Driving at very high speeds for
extended periods of time may result in damage to vehicle
components.
*
[DR10020(ALL)05/95]
Ford Motor Company recommends obeying posted speed limits.
*
[DR10100(ALL)06/95]
RWARNING
Do not spin the wheels at over 35 mph (55 km/h). The
tires may fail and injure a passenger or bystander.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

Driving Your Windstar
247
%*
[DR10200(ALL)01/95]
Driving in Bad Weather
%*
[DR10300(ALL)01/95]
Slippery roads
[DR10400(ALL)02/95]
n
Drive cautiously on wet or snowy roads.
*
[DR10500(ALL)03/95]
n
Do not quickly move the steering wheel unless necessary.
*
[DR10600(ALL)01/93]
n
Drive more slowly than you would normally.
[DR10650(ALL)02/95]
n
Do not use speed control.
*
[DR10700(ALL)01/95]
n
Give your vehicle more distance to stop.
*
[DR10800(ALL)01/93]
n
Use the ªsqueezeº technique for braking as described in
previous braking sections.
*
[DR10900(ALL)02/93]
n
Consider using one of the lower gears.
*
[DR11000(ALL)01/93]
RWARNING
To avoid skidding and losing control on slippery roads,
do not downshift into 1 (First) when you are moving
faster than 20 mph (30 km/h).
*
[DR11100(ALL)01/93]
RWARNING
The Anti-Lock Brake System may not prevent brake
lock-up on extremely slippery surfaces.
%*
[DR11200(ALL)01/95]
High water
*
[DR11300(ALL)05/90]
Do not drive through flooded areas unless you are sure that the
water is below the bottom of the wheel hubs.
*
[DR11400(ALL)01/93]
If you must drive through high water, drive slowly. You may
have limited traction or wet brakes so allow extra stopping
distance because your vehicle will not stop as quickly as usual.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

248
*
[DR11500(ALL)01/93]
After you drive through the standing water, apply your brakes
gently several times as your vehicle moves slowly to help dry
the brakes.
*
[DR11600(ALL)01/93]
Rocking the Vehicle
*
[DR11700(ALL)01/93]
If your vehicle gets stuck (for example, in mud or snow), you
may rock it out. Shift in a steady rhythm between forward and
reverse gears. At the same time, press lightly on the accelerator.
If you are still stuck after a few minutes of rocking, call for a
tow truck.
[DR11750(ALL)04/95]
NOTE: If your vehicle is equipped with Traction Control,
make sure the system has been turned off before
attempting to rock the vehicle.
[DR11775(ALL)04/95]
SeeTraction Control Off Lightin theLights and Gaugessection of
this guide for more information.
*
[DR11800(ALL)01/93]
Do not rock the vehicle for more than a few minutes. This may
overheat the engine, damage the transaxle, or damage the tires.
%*
[DR11900(ALL)03/95]
Driving With a Heavy Load
*
[DR12000(ALL)01/93]
The Safety Compliance Certification Label, located on the
driver's door pillar, provides important information regarding
the weight limits your vehicle can safely carry or tow. The total
weight of your vehicle, including the weight of the passengers
and cargo, should never be more than the Gross Vehicle Weight
Rating (GVWR). Also, the weight that your vehicle carries on
the front axle and rear axle should never be more than the
Gross Axle Weight Rating (GAWR) for the respective axle.
*
[DR12100(ALL)01/93]
The load capacities of your vehicle's tires affect the GVWR or
GAWR limitations. Using replacement tires with a higher weight
limit than the originals does not increase GVWR or GAWR.
Using lower capacity replacement tires may lower GVWR and
GAWR limitations.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

Driving Your Windstar
249
*
[DR12200(ALL)02/95]
RWARNING
If the GVWR or the GAWR specified on the Safety
Compliance Certification Label is exceeded, your vehicle
may be damaged or you may lose control and injure
someone.
*
[DR12300(ALL)01/93]
Vehicle/Trailer Loads
[DR12400(ALL)06/94]
Your vehicle may tow a Class I trailer up to 2,000 lbs. (907 kgs)
or 3,500 lbs. (1,587 kgs) with Trailer Tow Package provided the
Gross Vehicle Weight (GVW) is less than the GVWR shown on
the Safety Compliance Certification Label.
%*
[DR12500(ALL)04/95]
Towing a Trailer
*
[DR12600(ALL)01/93]
Towing a trailer puts an additional load on your vehicle's
engine, transaxle, axle, brakes, tires and suspension. For your
safety and for the good of your vehicle, use the right equipment
for the type of trailer you tow.
*
[DR12700(ALL)02/92]
n
Stay within the load limits when you tow.
*
[DR12800(ALL)01/93]
n
Carefully and thoroughly prepare your vehicle for towing,
making sure to use the right equipment and to attach it
properly. SeePreparing to Towin this section.
*
[DR12900(ALL)01/93]
n
Use extra caution when driving your vehicle while you tow.
SeeDriving While You Towin this section.
*
[DR13000(ALL)01/93]
n
Service your vehicle more frequently if you tow a trailer. See
Servicing Your Vehicle if You Towin this section.
*
[DR13100(ALL)05/94]
Do not tow a trailer until your vehicle has been driven at least
500 miles (800 km).
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

256
*
[DR19400(ALL)04/94]
Safety chains
*
[DR19500(ALL)01/93]
Always use safety chains between your vehicle and trailer.
Cross chains under the trailer tongue and allow slack for
turning corners. Connect safety chains to the vehicle frame or
hook retainers.Never attach chains to the bumper.
%*
[DR19600(ALL)01/93]
Trailer Brakes
*
[DR19700(ALL)01/93]
Separate trailer brakes are required on most trailers weighing
over 1,500 lbs. (680 kg).
*
[DR19800(ALL)05/95]
RWARNING
Do not connect a trailer's hydraulic brake system directly
to your vehicle's brake system. Your vehicle may not
have enough braking power and your chances of having
a collision greatly increase.
%*
[DR19900(ALL)01/93]
Trailer Lamps
*
[DR20000(ALL)01/93]
Make sure your trailer lamps conform to federal and local
regulations.
*
[DR20100(ALL)01/93]
Class I Trailer Tow electrical wiring provides two circuits (right
hand and left hand) to operate trailer stop/turn tail lamps. Each
stop/turn circuit will operate one combination stop/turn light
bulb (# 1157, 3157, 2357, or 3357) on the trailer. Never add more
than one trailer light bulb to one circuit.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

Driving Your Windstar
257
*
[DR20200(ALL)05/95]
RWARNING
Always replace a fuse with one that has the specified
amperage rating. Using a fuse with a higher amperage
rating can cause severe wire damage and could start a
fire.
%*
[DR20300(ALL)01/95]
Driving While You Tow
*
[DR20400(ALL)05/95]
Be especially careful when driving while you tow a trailer.
Never drive faster than 45 mph (70 km/h) when you tow in
hilly country on hot days. Also, anticipate stops so that you can
brake gradually.
*
[DR20500(ALL)01/93]
If you use the speed control while you are towing on very long,
steep grades, the speed control may shut off automatically.
*
[DR20600(ALL)01/93]
When descending a steep grade with a trailer, operate in Drive
rather than Overdrive. If additional braking is needed, shift into
2 (Second) or 1 (First) gear.
*
[DR20700(ALL)01/95]
Servicing your vehicle if you tow
[DR20800(ALL)09/93]
If you tow a trailer for a long distance, your vehicle will need
to be serviced more frequently than usual. See theMaintenance
Schedule and Record Booklet.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

258
*
[DR20900(ALL)01/93]
Trailer towing tips
*
[DR21000(ALL)11/89]
Before starting on a trip, practice turning, stopping and backing
in an area away from heavy traffic. Get to know the ªfeelº of
the vehicle/trailer combination.
*
[DR21100(ALL)01/93]
Practice backing up. Back up very slowly, with someone outside
at the rear of your trailer to guide you. Place your hand at the
bottom of the steering wheel and move it in the direction you
want the rear of the trailer to swing. Slight movement of the
steering wheel results in a much larger movement of the rear of
the trailer.
*
[DR21200(ALL)11/89]
When turning, drive slightly beyond the normal turning point
so the trailer wheels will clear curbs or other obstructions.
*
[DR21300(ALL)01/93]
Allow more room for stopping with a trailer attached. Trailer
brakes should be applied first, whether manually or
automatically controlled, when approaching a stop.
*
[DR21400(ALL)01/93]
For an easy-to-operate vehicle/trailer combination, the trailer
tongue load should be approximately 10-15% of the loaded
trailer weight.
*
[DR21500(ALL)02/94]
Make a thorough check of your equipment before starting out
on the road. After you have traveled about 50 miles (80 km),
stop in a protected area and double-check your hitch and
electrical connections. Also check trailer wheel lug nuts for
tightness.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

Driving Your Windstar
259
[DR21600(ALL)10/93]
When stopped in traffic for long periods of time in hot weather,
place the gearshift selector lever in P (Park) to increase the
engine idle speed. This aids in engine cooling and air
conditioner efficiency. If the engine overheats, turn the selector
knob to select the fresh air position to stop the air conditioner
compressor. Increase the engine speed for a short time.
*
[DR21700(ALL)01/93]
Vehicles with trailers should not be parked on a grade.
However, if you must park on a grade, place wheel chocks
under the trailer's wheels as follows:
[DR21800(ALL)11/93]1.
Apply the foot service brake pedal and hold.
*
[DR21900(ALL)11/93]2.
Have another person place the wheel chocks under the
trailer wheels.
[DR22000(ALL)11/93]3.
With the chocks in place, release the foot service brake
pedal, making sure the chocks are holding.
[DR22100(ALL)11/93]4.
Apply the parking brake by pressing the service brake pedal
down firmly with your right foot while applying the parking
brake lever with your right hand.
*
[DR22200(ALL)11/93]5.
Shift the gearshift lever into P (Park).
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

260
[DR22300(ALL)11/93]
Complete the following steps to start your vehicle after it has
been parked on a grade:
[DR22400(ALL)11/93]1.
Apply the foot service brake pedal and hold.
*
[DR22500(ALL)11/93]2.
Start the engine.
*
[DR22600(ALL)11/93]3.
Shift the gearshift lever into gear and release the parking
brake.
[DR22700(ALL)11/93]4.
Release the foot service brake pedal and move the vehicle
uphill to free the wheel chocks.
[DR22800(ALL)11/93]5.
Apply the foot service brake pedal and hold while another
person retrieves the chocks.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

262
*
[RE01400(ALL)03/95]
To avoid damaging your vehicle or your battery, and to avoid
injury to yourself, follow these directions for preparing your
vehicle to jump-start and connecting the jumper cables in the
order they are given. If in doubt, call for road service.
[RE01500(ALL)02/95]
To prepare your vehicle for jump-starting:
[RE01600(ALL)02/95]1.
Use only a 12-volt battery to jump-start your vehicle. Your
vehicle has a 12-volt starting system, so you need to use a
12-volt jumper system. You can damage your starting motor,
ignition system, and other electrical parts if you connect
them to a 24-volt power supply (either two 12-volt batteries
in series or a 24-volt motor generator set).
*
[RE01700(ALL)03/95]2.
Do not disconnect the battery of the vehicle that needs a
jump-start. You could damage the vehicle's electrical system.
*
[RE01800(ALL)03/95]3.
Park the second vehicle close to the hood of your vehicle,
but make sure the vehicles do not touch each other. Set the
parking brake on both vehicles and stay clear of the engine
cooling fan.
*
[RE01900(ALL)03/95]4.
Check the battery terminals and remove any excessive
corrosion before you attach the jumper cables.
*
[RE02000(ALL)01/93]5.
Turn on the heater blower in both vehicles. Turn off all other
switches and lights in both vehicles to prevent possible
damage to either vehicle's electrical systems.
File:wnres.ex
Update:Tue Mar 19 08:18:21 1996