ignition FORD WINDSTAR 1996 1.G Workshop Manual

208
%*
[AS09930(ALL)03/95]
High-Level Audio System
[AS09940(ALL)07/91]
Ford's High-Level Audio System delivers quality performance
for maximum listening enjoyment.
*
[AS09950(ALL)02/95]
Using the Controls on Your New Radio
*
[AS09960(ALL)04/95]
How to turn the radio on and off
*
[AS09970(ALL)04/95]
Press the ªPOWERº button to turn the radio on. Press it again
to turn it off.
*
[AS09990(ALL)04/95]
How to adjust the volume
*
[AS10000(ALL)05/95]
Press the (+/±) side of the ªVOLº button to increase/decrease
the volume. Bars illuminate in the display to show the relative
volume level.
*
[AS10010(ALL)04/95]
NOTE: If the volume level is set above a certain listening
level when the ignition switch is turned off, when the
ignition switch is turned back on, the volume will
come back to a ªnominalº listening level. However, if
the radio power is turned off (with the ªPOWERº
button), the volume will remain in the position it was
set at when radio power is switched back on.
*
[AS10020(ALL)04/95]
Selecting the AM or FM frequency band
*
[AS10030(ALL)07/92]
Push the ªAM/FMº button to select the desired frequency band.
When in the radio mode, pushing the button more than once
will alternate between AM, FM1 and FM2. These functions are
used with the station memory buttons described underHow to
Tune Radio Stations.
File:wnass.ex
Update:Tue Mar 19 08:19:39 1996

214
*
[AS10590(ALL)11/93]
NOTE: If you want to restart a currently playing tape
selection, press the left (
b) side of the ªSEEKº button
after three seconds into the current selection.
*
[AS10595(ALL)03/95]
Whirling sprockets in the display (l) indicate the direction
of tape travel.
*
[AS10600(ALL)01/95]
n
Using the ªSCANº function with your cassette tape player
*
[AS10700(ALL)03/95]
Press the ªSCAN/TUNEº button to enter the scan mode
(display indicates ªSCNº). Pushing the right (
a) side of the
ªSEEKº button will begin the forward scan mode on the tape
currently playing, stopping on each tape selection for
approximately an eight-second sampling.
*
[AS10800(ALL)03/95]
Pushing the left (
b) side of the ªSEEKº button will begin
the reverse scan mode, stopping on each previous tape
selection for approximately an eight-second sampling. While
scanning, the display indicates whirling sprockets plus an
ªSº (m).
*
[AS10810(ALL)02/95]
To stop the scan mode on the presently sampled tape
selection press the ªSCAN/TUNEº button again.
*
[AS10820(ALL)02/95]
How to eject the tape
*
[AS10830(ALL)04/95]
To stop the tape and eject the cassette, press the ªEJCTº button.
The radio will resume playing if the radio power is on. The
tape cartridge can be ejected with radio power (and/or ignition)
on or off.
*
[AS10840(ALL)01/95]
How to store the tape
*
[AS10850(ALL)03/95]
Press the ªAM/FMº button to stop the tape player and resume
radio play. The cassette will be stored in the tape player and
the
Xsymbol in the display will be lit until you push the
ªPLAY PROGº button to resume tape play. Fast forward and
fast rewind can be used while the tape is in storage mode
without interrupting radio play.
File:wnass.ex
Update:Tue Mar 19 08:19:39 1996

216
*
[AS11010(ALL)01/95]
Tape error messages
*
[AS11020(ALL)01/95]
Your cassette tape player is equipped to diagnose certain
problems you may experience. Error codes are as follows:
*
[AS11030(ALL)02/95]
Error 0Ð Communication error between the radio controller
and the tape controller. The cassette player will eject the tape.
Insert the tape again. If the same error code appears, turn the
ignition off, then back on again and insert the tape.
*
[AS11040(ALL)02/95]
Error 1Ð Possible problem cartridge. The cassette tape player
will eject the tape. Insert the tape again. If the same error code
appears in the display, try a different cartridge.
*
[AS11050(ALL)02/95]
Error 2Ð Tape eject or load failure. Your cassette tape player
will go into the pause mode. Push ªEJCTº to eject the tape. If
the tape doesn't eject, refer the problem to qualified personnel
for service.
%*
[AS11060(ALL)03/95]
Clock Operation
*
[AS11080(ALL)07/90]
How to view the clock mode
*
[AS11090(ALL)07/93]
Press the ªCLOCKº button to alternate the frequency and time
in the display. In the clock mode, pressing any radio function
will automatically display the radio frequency for approximately
ten seconds before changing back to the clock mode.
*
[AS11100(ALL)07/90]
How to set the clock
[AS11120(ALL)12/93]
Press and hold in the ªCLOCKº button, press the ªSEEKº
button left (
b) to advance the hours and right (
a) to advance
the minutes.
*
[AS11130(ALL)11/93]
NOTE: The clock displays 12-hour time with no AM/PM
indications.
[AS11135(ALL)11/93]
NOTE: On the High-Level Audio System, the clock can be set
with the radio power on or off.
File:wnass.ex
Update:Tue Mar 19 08:19:39 1996

222
*
[AS21095(ALL)12/93]
Setting the AM or FM frequency band
*
[AS21100(ALL)05/94]
Push the ªBANDº button to change the frequency band.
*
[AS21105(ALL)09/94]
Using the ªMEMORYº button
*
[AS21110(ALL)04/95]
Push the ªMEMORYº button to access the station you have set
into memory button 1 on the face of the radio. Successively
pushing this button will access, numerically, all stations set into
the Station Memory Preset buttons (1 through 5).
*
[AS21115(ALL)09/94]
How to turn the speakers on and off
*
[AS21120(ALL)09/94]
When the rear seat controls are on, push the ªSPKRS ON-OFFº
button to turn all speakers off. Push again to turn all speakers
on.
*
[AS21125(ALL)12/93]
NOTE: Turning the ignition off, then on again will not turn
the speakers back on, if previously turned off by the
ªSPKRS ON-OFFº button on the rear seat controls.
*
[AS21130(ALL)09/94]
Using the ªSEEKº function
*
[AS21135(ALL)12/93]
Press the right (
a) side of the ªSEEKº rocker switch to seek to
the next radio station. Press the left (
b) side of the ªSEEKº
rocker switch to seek to the previous radio station.
*
[AS21140(ALL)07/94]
NOTE: When using the rear seat controls with a High-Level
Audio System, the ªSEEKº function on the rear seat
controls will also function with cassettes, seeking the
next (ªSEEK
aº) or previous (ª
bSEEKº) selection
on the tape.
*
[AS21145(ALL)12/93]
Using headphones with the rear seat controls
*
[AS21150(ALL)12/93]
Two 3.5mm headphone jacks have been provided on the rear
seat controls. Plug headphone(s) into the provided jack(s) to
operate headphones.
File:wnass.ex
Update:Tue Mar 19 08:19:39 1996

Electronic Sound Systems
225
%*
[AS21300(ALL)05/95]
Electronic Stereo and Stereo Cassette
Radios
*
[AS21400(ALL)02/95]
Using the Controls on Your New Radio
*
[AS21500(ALL)02/95]
How to turn the radio on and adjust the volume
*
[AS21701(ALL)04/95]
Press the ªPOWERº button to turn the radio on. Press it again
to turn it off.
*
[AS21950(ALL)05/95]
Press the right (+) side of the ªVOLUMEº button to increase the
volume. Press the left (-) side of the button to decrease the
volume. Illuminated bars in the display show the relative
volume level.
*
[AS21975(ALL)04/95]
NOTE: If the volume level is set above a certain listening
level when the ignition switch is turned off, when the
ignition switch is turned back on, the volume will
come back to a ªnominalº listening level. However, if
the radio power is turned off (with the ªPOWERº
button), the volume will remain in the position it was
set at when radio power is switched back on.
*
[AS22100(ALL)04/95]
Selecting the AM or FM frequency band
*
[AS22225(ALL)02/95]
Push the ªAM/FMº button to select the desired frequency band.
Pushing the button more than once will alternate between AM,
FM1 and FM2. These functions are used with the station
memory buttons described underHow to tune radio stations.
*
[AS22300(ALL)05/95]
How to tune radio stations (Stereo Radio)
*
[AS22400(ALL)05/95]
There are three ways for you to tune in to a particular station.
You can manually locate the station by using the ªTUNEº
button, ªSEEKº the station or select the station by using the
memory buttons, which you can set to any desired frequency.
File:wnass.ex
Update:Tue Mar 19 08:19:39 1996

236
% [DR01600(ALL)09/93]
Brake-Shift Interlock Safety Feature
[DR01700(ALL)05/95]
Your vehicle has a special brake-shift interlock safety feature
which prevents you from shifting out of P (Park) without the
brake pedal depressed. To shift the transaxle out of the P (Park)
position, the ignition must be in the ON position and your foot
must be pressing on the brake pedal.
[DR01750(ALL)02/96]
When parking on a hill, set the parking brake before shifting
into and out of P (Park). If the parking brake is not set, a clunk
or bang may be heard when shifting out of P (Park). This noise
can be considered a normal characteristic.
*
[DR01800(ALL)04/95]
If the shift lever cannot be moved from the P (Park) position
with the brake pedal depressed:
*
[DR01900(ALL)01/93]1.
Shut the engine off and remove the ignition key.
*
[DR02000(ALL)01/93]2.
Apply the parking brake.
*
[DR02100(ALL)01/93]3.
Reinsert the ignition key and turn it clockwise to the first
position (OFF).
*
[DR02200(ALL)04/95]4.
Depress the brake pedal, move the gearshift lever to N
(Neutral) and start the engine.
*
[DR02280(ALL)05/95]
If you need to shift out of P (Park) by using the alternate
procedure described above, it is possible that a fuse has blown
and that your brakelamps may also not be functional. Please
refer to the chapter titledServicing Your Windstarin this Owner
Guide for instructions on checking and replacing fuses.
*
[DR02300(ALL)05/95]
RWARNING
DO NOT DRIVE YOUR VEHICLE UNTIL YOU VERIFY
THAT THE BRAKELAMPS ARE WORKING.
%*
[DR02500(ALL)06/92]
Backing Up
*
[DR02600(ALL)01/93]
Before shifting into or out of R (Reverse), you should always
come to a complete stop.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

Driving Your Windstar
245
*
[DR08700(ALL)01/93]
RWARNING
When parking, do not use the gearshift in place of the
parking brake. Always set the parking brake fully and
make sure that the gearshift is securely latched in Park
(P). Turn off the ignition whenever you leave your
vehicle. Never leave your vehicle unattended while it is
running. If you do not take these precautions, your
vehicle may move unexpectedly and injure someone.
*
[DR08900(ALL)01/93]
RWARNING
If the parking brake is fully released, but the Brake
System light remains on, have the brakes checked
immediately. They may not be working properly.
*
[DR09000(ALL)02/94]
The parking brake is not designed to stop a moving vehicle, but
you can use the parking brake to stop your vehicle in an
emergency if the service brakes fail. However, since the parking
brake does not stop your vehicle as quickly as the normal
brakes, the stopping distance will increase greatly.
%*
[DR09100(ALL)01/95]
Driving Under Special Conditions
%*
[DR09200(ALL)01/95]
Tips for Safe Driving
*
[DR09300(ALL)01/93]
As with any new vehicle, yours may drive and handle
differently from your previous vehicle. Use greater care until
you become accustomed to its features and driving
characteristics.
*
[DR09400(ALL)01/93]
Always operate your vehicle within reasonable limits. Abrupt
changes in acceleration, deceleration, turning, or combinations of
these maneuvers can cause a vehicle to behave differently than
anticipated, especially when road conditions vary.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

262
*
[RE01400(ALL)03/95]
To avoid damaging your vehicle or your battery, and to avoid
injury to yourself, follow these directions for preparing your
vehicle to jump-start and connecting the jumper cables in the
order they are given. If in doubt, call for road service.
[RE01500(ALL)02/95]
To prepare your vehicle for jump-starting:
[RE01600(ALL)02/95]1.
Use only a 12-volt battery to jump-start your vehicle. Your
vehicle has a 12-volt starting system, so you need to use a
12-volt jumper system. You can damage your starting motor,
ignition system, and other electrical parts if you connect
them to a 24-volt power supply (either two 12-volt batteries
in series or a 24-volt motor generator set).
*
[RE01700(ALL)03/95]2.
Do not disconnect the battery of the vehicle that needs a
jump-start. You could damage the vehicle's electrical system.
*
[RE01800(ALL)03/95]3.
Park the second vehicle close to the hood of your vehicle,
but make sure the vehicles do not touch each other. Set the
parking brake on both vehicles and stay clear of the engine
cooling fan.
*
[RE01900(ALL)03/95]4.
Check the battery terminals and remove any excessive
corrosion before you attach the jumper cables.
*
[RE02000(ALL)01/93]5.
Turn on the heater blower in both vehicles. Turn off all other
switches and lights in both vehicles to prevent possible
damage to either vehicle's electrical systems.
File:wnres.ex
Update:Tue Mar 19 08:18:21 1996

Roadside Emergencies
267
%*
[RE03800(ALL)01/93]
Changing a Flat Tire
*
[RE03900(ALL)01/95]
If you get a flat tire while you are driving, do not apply the
brake heavily. Instead, gradually decrease the speed. Hold the
steering wheel firmly and slowly move to a safe place on the
side of the road. Park on a level spot, turn off the ignition, set
the parking brake, and turn on the hazard flashers.
% [RE04000(ALL)02/95]
Using the Spare Tire
*
[RE04100(ALL)03/94]
Your vehicle has a temporary spare tire (unless you ordered the
optional full-size spare tire). This spare tire is smaller than a
regular tire and is designed for emergency use only. Use it only
when you get a flat tire and replace it as soon as you can. This
spare tire is marked with the words TEMPORARY USE ONLY
so that you can easily identify it.
*
[RE04200(ALL)01/93]
RWARNING
If you use the temporary spare tire continuously or do
not follow these precautions, the tire could fail, causing
you to lose control of the vehicle, possibly injuring
yourself or others.
*
[RE04300(ALL)02/95]
When you drive with the temporary spare tire, DO NOT:
*
[RE04500(ALL)02/95]
n
exceed 50 mph (80 km/h) under any circumstances
*
[RE04600(ALL)01/93]
n
load your vehicle so that it is heavier than the maximum
vehicle load rating listed on the tire decal
*
[RE04700(ALL)01/93]
n
tow a trailer
*
[RE04800(ALL)01/93]
n
use tire chains
*
[RE04900(ALL)01/93]
n
try to repair the temporary spare tire or remove it from its
wheel
File:wnres.ex
Update:Tue Mar 19 08:18:21 1996

302
*
[SV02700(ALL)01/95]
n
Never get under a vehicle while it is supported by a jack
only. If you must work under a vehicle, use safety stands.
*
[SV02800(ALL)01/95]
n
Keep all lit cigarettes and other smoking materials away
from the battery and all fuel-related parts.
*
[SV02900(ALL)03/95]
Working Under the Hood
[SV03000(ALL)02/95]
Before you open the hood, read this section carefully.
*
[SV03100(ALL)02/95]
If you plan to work under the hood while the engine is
off:
*
[SV03200(ALL)01/93]
RWARNING
Set the parking brake and make sure the gearshift is
securely latched in P (Park). This will prevent your
vehicle from moving unexpectedly.
*
[SV03300(ALL)01/93]
RWARNING
Always remove the key from the ignition after you turn
off the engine.
*
[SV03400(ALL)03/95]
If you must work under the hood while the engine is
on:
[SV03500(ALL)05/95]
RWARNING
Set the parking brake and make sure that the gearshift is
securely latched in P (Park). This will prevent your
vehicle from moving unexpectedly.
*
[SV03600(ALL)03/95]
RWARNING
Do not wear loose clothing or jewelry that can get caught
in the moving parts.
File:wnsvs.ex
Update:Tue Mar 19 08:16:43 1996