ECU FORD WINDSTAR 1998 1.G Owner's Guide

252
[ER08400(ALL)01/96]2.
Get out the spare tire and jack. See previous section for
instructions on spare tire removal. The jack is located in the
rear storage compartment in the right door panel of the
cargo area. Remove wing bolt to unfasten jack.
[ER08500(ALL)01/96]
17-1/2 pica
art:0050043-C
Jack storage
[ER08600(ALL)08/96]3.
Insert the tapered hook end of the jack handle behind the
wheel cover of the tire to be changed and gently pry it off.
When you want to replace the wheel cover, simply align the
valve stem to the slot in the cover and press it back on.
[ER08650(ALL)08/96]
To replace wheel covers, line up the valve hole of the wheel
cover (see back of wheel cover for location information) over
the valve stem. While pressing the wheel cover against the
wheel, hit the outer edge with your palm or a rubber mallet
until the wheel cover is fully secured on the wheel.
File:10wners.ex
Update:Mon Oct 7 11:47:52 1996

254
[ER08865(ALL)08/96]
To replace the wheel ornament, align the tabs of the ornament
with the opening in the wheel. Push the ornament with your
palm until it is fully secured into the wheel opening.Do not
use excessive force or a metal hammer to install wheel covers
or wheel ornaments.
[ER08900(ALL)09/96]
13-1/2 pica
art:0050044-C
Wheel cover removal (optional cast aluminum wheels)
*
[ER09000(ALL)01/96]4.
Fit the hex-shaped end of the lug wrench over the wheel lug
nuts and loosen them one-half turn (counterclockwise). Do
not remove the wheel lug nuts until you raise the tire off the
ground.
%*
[ER09100(ALL)01/96]
If your vehicle has the optional locking lug nuts, you must
use the lug nut removal tool provided with your vehicle's
tool kit.
File:10wners.ex
Update:Mon Oct 7 11:47:52 1996

260
%*
[ER11000(ALL)01/96]
7-1/2 pica art:0040176-A
Lug nut tightening sequence
[ER11100(ALL)01/96]
The lug nuts should be tightened to 83-113 ft-lb (113-153 Nm).
*
[ER11200(ALL)01/96]13.
Replace the wheel cover by pressing it into place. If you
have the standard wheel covers, you must align the notch in
the wheel cover with the tire's valve stem and align the
recess in the back of the wheel cover with one of the lug
nuts. If you have the optional aluminum wheel, press the
center wheel cap into place after matching up the design of
the wheel cap to the wheel.
[ER11300(ALL)01/96]14.
Replace the jack in the storage compartment and make sure
the jack is securely fastened.
*
[ER11400(ALL)01/96]15.
Store the flat tire under the vehicle just as you would store
the spare tire. Refer to the section onStowing the Spare Tire
in this chapter.
[ER11500(ALL)01/96]16.
Unblock the wheels.
*
[ER11600(ALL)01/96]
Retighten the lug nuts to the specified torque at 500 miles
(800 km) of operation, after any wheel change, or any time the
lug nuts are loosened.
File:10wners.ex
Update:Mon Oct 7 11:47:52 1996

Roadside Emergencies
261
*
[ER11700(ALL)01/96]
Stowing the spare tire
[ER11800(ALL)01/96]1.
To raise the tire to the stowed position, lay the tire on the
ground with the interior side facing up. Install the retainer
through the wheel center and slide the tire under the vehicle.
Fit the hex-shaped end of the wheel lug wrench over the hex
nut in the floor of the cargo area. Turn the wheel lug
wrench clockwise until the tire is raised to its original
position underneath the vehicle.
[ER11850(ALL)08/96]
If your vehicle has 16" wheels, lift one end of the tire, route the
cable end through the center of the wheel and install the 16"
wheel retainer.
[ER11900(ALL)01/96]
NOTE: The hex nut ratchets when the tire is raised to the
stowed position. It will not allow you to over-tighten.
*
[ER12000(ALL)01/96]2.
Check for proper seating against the underbody supports
and retighten if necessary.
[ER12100(ALL)01/96]
RWARNING
Check the tire seating position for looseness and make
sure the tire is not too far forward to avoid axle contact.
*
[ER12200(ALL)01/96]
RWARNING
Make sure the spare tire and jacking equipment are
stowed and secured in the proper storage location.
File:10wners.ex
Update:Mon Oct 7 11:47:52 1996

272
[MC03200(ALL)01/96]
24 pica art:0050028-B
Propping the hood
*
[MC03300(ALL)01/96]
To close the hood:
*
[MC03400(ALL)01/96]1.
Remove the prop rod from the slotted hole in the hood.
Place the rod in its retaining clip and close the hood with
enough force to make it latch. Be sure to oil the hood latch
every six months to maintain smooth operation.
*
[MC03500(ALL)01/96]2.
Try to lift the hood after closing it to be sure it is securely
latched.
File:11wnmcs.ex
Update:Tue Oct 8 10:24:50 1996

Maintenance and Care
277
%*
[MC04900(ALL)09/96
]
Engine oils with anSAE 5W-30viscosity arePREFERREDfor
your vehicle. They provide the best engine performance, fuel
economy and engine protection for all climates down to-15ÊF
(-26ÊC).
%*
[MC05000(ALL)03/96]
Synthetic engine oils which are CERTIFIED and of the preferred
viscosity may be used in your engine. The engine oil and oil
filter must still be changed according to the maintenance
schedule.
%*
[MC05100(ALL)01/96]
Checking and Adding Engine Oil
*
[MC05200(ALL)01/96]
Since the proper amount of engine oil is important for safe
engine operation, check the oil using the dipstick each time you
put fuel in your vehicle. Remember the engine must be off, the
oil must be warm and the vehicle must be parked on level
ground.
%*
[MC05300(ALL)01/96]
Checking the engine oil level:
*
[MC05400(ALL)01/96]1.
Turn the engine off after it has warmed up and allow a few
minutes for the engine oil to drain back into the oil pan.
*
[MC05500(ALL)01/96]2.
Set the parking brake, making sure the gearshift is securely
latched in P (Park).
*
[MC05600(ALL)01/96]3.
Open the hood. Protect yourself from engine heat.
[MC05700(ALL)01/96]4.
Locate the dipstick labelled ªEngine Oilº and carefully pull it
out of the engine.
*
[MC05800(ALL)01/96]5.
Wipe the dipstick clean and put it back into position, making
sure it is fully seated.
File:11wnmcs.ex
Update:Tue Oct 8 10:24:50 1996

Maintenance and Care
289
%*
[MC13700(ALL)01/96]
Checking the Automatic Transaxle Fluid
*
[MC13800(ALL)01/96]
With the vehicle on a level surface, start the engine and move
the gearshift lever through all of the gear ranges allowing
sufficient time for each position to engage. Securely latch the
gearshift lever in the P (Park) position, fully set the parking
brake and leave the engine running.
*
[MC13900(ALL)01/96]
Wipe off the dipstick cap, pull the dipstick out and wipe the
indicator end clean. Put the dipstick back into the filler tube and
make sure it is fully seated. Pull the dipstick out and read the
fluid level.
[MC14000(ALL)01/96]
When checking fluid at normal operating temperature, the fluid
level should be within the crosshatched area on the dipstick.
[MC14100(ALL)09/96]
7-1/2 pica art:0050021-B
The automatic transmission dipstick
[MC14200(ALL)01/96]
NOTE: Your vehicle should not be driven until some fluid
has been added if the fluid level is below the bottom
hole on the dipstick and the outside temperature is
above50ÊF (10ÊC). Addonly enough fluid to bring the
level above the bottom hole. The fluid level should be
rechecked at normal operating temperature.
[MC14230(ALL)09/96]
If the vehicle has not been driven and the fluid level is above
the bottom hole on the dipstick, do not add fluid. Recheck the
fluid level after your vehicle has reached normal operating
temperature.
File:11wnmcs.ex
Update:Tue Oct 8 10:24:50 1996

Maintenance and Care
299
[MC20800(ALL)08/96]
Snow Chains
[MC20900(ALL)08/96]
The tires on your vehicle have all-weather treads that provide
traction in rain or snow. However, during the winter months in
some climates, you may need to use chains with your tires. Use
tire chains with P205/70R15 tires only.
*
[MC21100(ALL)01/96]
Do not use chains when using a temporary spare. For full size
tires, use chains on the tires only in an emergency or if the law
requires them where you live. When you use the tire chains:
*
[MC21200(ALL)01/96]
n
Make sure the chains are the right size for your tires. Use
only SAE Class ºSª chains. Other types may damage your
vehicle.
*
[MC21300(ALL)01/96]
n
Put chains on tightly with the ends held down securely.
Follow the chain manufacturer's instructions.
*
[MC21400(ALL)01/96]
n
Drive slowly. If you can hear the chains rub or bang against
your vehicle, stop the vehicle and tighten the chains. If you
continue to hear the chains rub or bang against your vehicle,
remove the chains to prevent damage to your vehicle.
*
[MC21500(ALL)01/96]
n
Avoid fully loading your vehicle if possible.
*
[MC21600(ALL)01/96]
n
Remove tire chains at the first opportunity after using them
on snow and ice. Do not use the chains on dry roads.
[MC21800(ALL)01/96]
Be sure:
[MC21900(ALL)01/96]
n
The chains are fully tightened
[MC22000(ALL)01/96]
n
The vehicle is driven below 30 MPH (50 km/h)
[MC22100(ALL)01/96]
n
The vehicle is lightly loaded
[MC22200(ALL)01/96]
n
To avoid sharp turns
*
[MC22300(ALL)01/96]
Make sure your suspension insulators and bumpers are not
missing or worn to avoid damage to your vehicle.
File:11wnmcs.ex
Update:Tue Oct 8 10:24:50 1996

342
*
[AC01400(ALL)01/93]
Safety Equipment
*
[AC01500(ALL)11/93]
Vehicle Security Systems
*
[AC01600(ALL)01/93]
Travel Equipment
[AC01700(ALL)05/95]
Soft Luggage Carrier
Aero Hood Deflector
Factory Luggage Rack & Adaptors
Trailer Hitch (Class II)
Console
*
[AC01800(ALL)05/96]
NOTE: When adding accessories, equipment, passengers, and
luggage to your vehicle, do not exceed the total
weight capacity of the vehicle or of the front or rear
axle (GVWR, GAWR as shown on the Safety
Compliance Certification Label). Consult your dealer
for specific weight information.
*
[AC01900(ALL)09/95]
NOTE: Devices that emit radio frequency (RF) energy such as
AM/FM radios, mobile communication systems
(two-way radios, telephones) and radio controlled
security systems, are subject to the rules and
regulations of the Federal Communications
Commission (FCC) 47 CFR Parts 2 and 15. Any such
system installed in your vehicle should comply with
those rules and should be installed only by a
qualified technician. In addition, to insure continued
compliance with the FCC's requirements, RF devices
must not be modified or changed in a manner not
expressly approved by Ford Motor Company.
File:15wnacs.ex
Update:Mon Oct 7 11:50:14 1996