battery location GEELY CK 2008 Workshop Manual

250(2) Trouble indication
1In case of a trouble, the warning light will indicate. If the external trouble is a history trouble, the indication
will be cancelled. When the history trouble happens for no less than 5 times, the indicator light will remain
on even if there is no more trouble. "Low battery voltage" shall not be counted in the total number of
troubles.
2Only a service worker can reset a displayed or history trouble. The internal troubles of a SRS ECU
(HAE2.5) or the "crash record" of a trouble cannot be reset, in which case the SRS ECU (HAE2.5) shall
be replaced.
(3) Microcontroller-independent warning light on
Microcontroller with definitive troubles cannot fulfill its functions, thus cannot control the warning light. In
this case, the warning light will light up through proper circuit regardless of the microcontroller as stated
below:
yMalfunction of the battery supplying power to SRS ECU (HAE2.5): the warning lights are turned
on continuously by means of the drive function of the selfcheck light.
yLoss of internal working voltage: the warning light remains on.
yReset due to trigger failure of the watchdog: the warning light blinks.
yMicrocontroller out of work: the warning light always lights up.
yIncomplete insertion of SRS ECU (HAE2.5) connector: the warning light remains on by means of
a shorting bar.
The diagnostic procedures can well be illustrated as follows:
If it is found that the SRS warning light remains on, follow the undermentioned procedures to check even if
the light goes out eventually. First, a scan meter is used to check the location of the trouble.
Then£¬go on with the checking in accordance with specific methods and procedures for the correspondent
location.
a. If the result indicates that it is an internal trouble or that the SRS is already detonated, replace the
ECU directly.
b. Troubleshooting.

265III. KEY POINTS FOR INSTALLATION1. Pre-Check
(1) The new airbag or clock spring shall be checked before being installed.
(2) Connect negative (-) terminal cable of the battery.
(3) Connect Hi-DS T to the diagnostic interface (16 connector).
(4) Turn the ignition switch ON.
(5) Read the diagnostic circuit and see if the other locations than the troubled area of the airbag are normal.
(6) Turn the ignition switch ON.
(7) Remove the negative (-) terminal cable from the battery, and protect it with insulating tape for insulation.
2. Installation of clock spring: align the clock spring and install it to the
steering wheel.
yCenter alignment of the clock spring
Screw up the clock spring clockwise to the end, rotate it counterclock-
wise by 2.5 turns, and align it with the mark (see the figure below).
3. Install the components of the steering wheel and airbag assembly
(1) When the center of the clock spring is aligned, install the components of the steering wheel and airbag
assembly.
(2) After being installed, rotate the left and right sides of the steering wheel to position, and make sure there
is no abnormality.NOTICEIn case of scrapping an airbag, it shall be noted that the airbag shall be deployed according to the specifiedprocedures before being scrapped.
When connecting or disconnecting the Hi-DS T, turn the ignition switch OFF first.NOTICE:
Work must be started 60s after the negative (-) terminal cable is disconnected from battery.NOTICE:
If the center of the clock spring cannot be aligned, the steering wheel
will not turn midway, or cause bad performance to the clock spring
circuit, consequently hamper the normal action of the airbag.NOTICEWhen installing the components of the steering wheel and airbag assembly, attention should be given toprotect the wire harness of the clock spring from seizure.

2696Try to disconnect at a location far away from the vehicle the connector of the wire harness for deployment
of the driver airbag assembly, connect them with the two terminals of the battery removed from the
vehicle and deploy the airbag (see the figure below).
7The deployed driver airbag assembly shall be scrapped according to the scrapping procedures.
(3) Deploy outside the vehicle
NOTICE:
Keep the airbag over 6m away from a obstacle or person and deploy the airbag in an open flat area.
1Disconnect the positive (+) and negative (-) terminal cables from the battery and remove the battery
from the vehicle.
2The airbag assembly shall be deployed according to the following procedures.
(4) Driver airbag assembly
1Remove the driver airbag assembly from the vehicle.Vehicle CoverWire Harness
for DeploymentNOTICE
Make sure there is no man inside or near the vehicle and then carry out the operations.
After the driver airbag is deployed, the gas generator is of high temperature. Keep it for 30 minutes until it
gets cool for use.
If the driver airbag assembly cannot be deployed, discuss the problem with the local Geely service station.NOTICE
Work must be started 60s after removal of the battery.NOTICE
When the connector is not connected, the terminals of the driver airbag assembly will be short circuited
automatically, preventing the airbag from being deployed unexpectedly. If the airbag is deployed unexpectedly,
the deployed surface should face up. It should be kept on a flat surface without any other items on it.

2717Put three old tires without hubs onto the tire used to fix the driver airbag assembly (see the figure below).
8Try to disconnect at a location far away from the vehicle the connector of the wire harness for deployment
of the driver airbag assembly, connect with the two terminals of the battery removed from the vehicle
and deploy the airbag (see the figure below).
9the deployed driver airbag assembly shall be scrapped according to the scrapping procedures.Wire Harness for DeploymentOld Wheels
without HubWire Harness
for DeploymentNOTICE
Make sure to deploy the driver airbag assembly when there is no person close by.After the driver airbag is deployed, the gas generator is of high temperature. Keep it for over 30 minutesuntil it gets cool for use