wheel GEELY FC 2008 Owners Manual

Panel/combination instrument-- panel
CodeShape
CodeShape
CodeShape
<>
=4.8
=13
2204813<>
=4.8
=19
2754819<>
=6
=20
1740620
<>
=4.8
=9.5
2754895<>
=6
=16
1400616<>
=6
=20
1400620
Panel
Preparation
1. Automobile prepares to equip with SRS airbag and safety belt pre-tension crimper.
Parking disassembling and assembling works in this chapter might influence SRS airbag. Before imple-
menting these works, it is necessary to read the notes in SRS chapter.
Change
1. Schedule for bolt, screw and screw cap
Note: when using screw driver to unclench fixing clasp or fixing clamp, it is necessary to wrap
the needled top of wrench with adhesive tape.
Hint: when disassembling or assembling panel, if necessary, use the figure and code in following
table to choose bolt, screw and screw cap.
2. Preparation
3. Disassemble leading wire of battery cathode
4. Turn front wheel to face the front
 340 
mm

Panel/combination instrument-- panel
3 Fixing clamp
4 Fixing clasp
5. Disassemble safety airbag assembly at the side of
driver [67010011] (Referring to page 261)
6. Disassemble steering wheel assembly [67010001]
(referring to page 194)
7. Disassemble Combination instrument cover
[68000077]
(a) Disassemble fixing clamp.
(b) Use screw driver to unclench three fixing clamps and four
fixing clasps, then disassemble Combination instrument.
Hint: before using screw driver, it is necessary to wrap
its needled top with adhesive tape.
8. Disassemble Combination instrument assembly
[67000081]
(a) Disassemble A screw.
(b) Liking that shown in figure, unclench two fixing clamps.
(c) Disassemble the joint, then disassemble Combination in-
strument assembly.
9. Disassemble panel left ventilation hole assembly
[68010010]
Use disassembling tool for trim tape to disassemble panel left
ventilation hole assembly.
Hint: before using screw driver, it is necessary to wrap its
needled top with adhesive tape.
10. Disassemble panel right ventilation hole assembly
[68010011]
11. Disassemble front ashtray
12. Disassemble shift organization trim board assem-
bly [68000076]
(a) Use screw driver to unclench six fixing clamps.
Hint: before using screw driver, it is necessary to wrap
its needled top with adhesive tape.
(b) Disassemble the joint, then disassemble shift organization
trimmain board.
 341 
4 Fixing clasp
6 Fixing clamp

Panel/combination instrument--panel
(b) Assemble CD machine assembly and panel central ventila-
tion hole assembly.
36. Assemble helix cable assembly (referring to page
261)
37. Assemble steering wheel assembly [67010001]
(referring to page 194)
38. Check the central position of steering wheel.
39. Check the safety airbag assembly at the side of
driver [67010011] (referring to page 249)
40. Assemble the safety airbag assembly at the side of
driver [67010011]
41. Check the warning light of SRS airbag
Fixing
clamp
4 Fixing
clamp
 346 

Exterior/inner trim board--Front bumper
Exterior/inner trim board
Front bumper
Subassembly
Inner gasket of
right front wheel
Inner gasket of
left front wheel Fixing pedestal of
radar probe
Radar probe head
Radar probe head
Fixing pedestal of
radar probe head
Front fog light assemblyRadiator cover
assembly
Front bumper
Equipping with fog light
 379 

Exterior/inner trim board--Front bumper
Change
Hint:
zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; if necessary, it will have assembling instruction.
zPlease refer to subassembly figure of front bumper on page 379.
1. Disassemble radiator cover assembly [68000094]
(a) Disassemble the bolt and radiator cover assembly.
2. Disassemble inner gasket of left front wheel [68000225]
(a) Use disassembling tool for fixing clamp to disassemble two fixing clamps.
(b) Disassemble the screw and a part of inner gasket of left front wheel.
Hint: Disassemble the fixing clamp of screw and inner gasket of left front wheel in the scope of
front bumper which could be disassembled.
3. Disassemble inner gasket of right front wheel [68000228]
4. Disassemble front bumper [68000005]
(a) Disassemble four screws and two fixing clamps.
(b) Disassemble fixing clasp and front bumper.
(c) Equipping with fog light: disassemble two joints of fog light.
(d) Equipping with radar probe head: disassemble two radar probe heads (luxury type).
5. Disassemble reversing radar probe head assembly.
(a) Disassemble two fixing pedestals of radar probe head and two radar probe heads.
6. Disassemble left front fog light assembly [67000098]
(a) Disassemble fixing clasp and left front fog light assembly.
7. Disassemble right front fog light assembly [67000099]
 380 

Rear bumper
Subassembly
Exterior/inner trim board--Rear bumper
Equipping with
reversing radar:
reversing radar
probe headEquipping with
reversing radar:
reversing radar
probe head Equipping with radar:
fixing pedestal of radar
probe head Left decoration of
luggage cas
Right decoration of trunk
Rear trim board of
trunk
Trim board of right
rear wheel
Mudguard of left
rear wheelRear bumper
Mudguard of right
rear wheel Trim board of left
rear wheel
 381 

Change
Hint:
zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; if necessary, it will have assembling instruction.
zPlease refer to subassembly figure of rear bumper on page 381.
Exterior/inner trim board--Rear bumper
 382  1. Disassemble trunk carpet assembly [68000114]
2. Disassemble rear trim board of trunk [68000118]
(a) Use two fixing clasps.
(b) Use disassembling tool for trim tape to disassemble rear
trim board of trunk.
3. Disassemble left decoration of trunk [68000112]
(a) Use disassembling tool for fixing clamp to disassemble
fixing clamp and a part of left decoration of trunk.
Hint:
Disassemble the fixing clasp and left decoration of trunk in the scope of screw cap used for
fixing rear bumper and trunk which could be disassembled.
4. Disassemble right decoration of trunk [68000113]
5. Disassemble mudguard of left rear wheel [68000223]
(a) Disassemble two screws and mudguard of left rear wheel.
6. Disassemble mudguard of right rear wheel [68000224]
7. Disassemble trim board of left rear wheel [68000230]
(a) Use screw driver to disassemble fixing clasp from rear bumper.
(b) Use disassembling tool for fixing clasp to disassemble fix-
ing clasp.
(c) Disassemble trim board of left rear wheel.
Hint: Disassemble trim board of left rear wheel in the
scope of screw used for fixing rear bumper which could
be disassembled.
8. Disassemble trim board of right rear wheel [68000231]
9. Disassemble rear bumper [68000012]
(a) Use screw driver to disassemble two fixing clasps.
(b) Disassemble four screw caps and two screws.
(c) Disassemble fixing clasp and rear bumper.
(d) Equipping with radar probe head: disassemble four joints of
radar probe head.
10. Disassemble reversing radar probe head assembly.
(a) Disassemble fixing pedestal of radar probe and radar probe.
11. Disassemble left rear fog light assembly [67000100]
(a) Disassemble fixing nut and left rear fog light assembly.
12. Disassemble right rear fog light assembly [67000101]

Exterior/inner trim board--Left lower fender of automobile body
Left lower fender of automobile body (LH)
Subassembly
 388 
Lower fender
Mudguard of
left front wheel
Fixing clasp

Exterior/inner trim board--Left lower fender of automobile body
Change
Hint:
When assembling, please work by the sequence which is opposite with disassembling sequence;
if necessary, it will have assembling instruction..
Changing procedure for right side is same as the left side.
Please refer to the subassembly figure of body left lower fender on page 388.
 389  1. Disassemble mudguard of left front wheel [68000221]
(a) Disassemble three screws and mudguard of left front wheel.
2. Disassemble body left lower fender [68000049]
(a) Use disassembling tool for fixing clamp to disassemble eight
fixing clamps.
(b) Disassemble the screw.
(c) Use disassembling tool for trim tape to disassemble body
left lower fender.