glove box GEELY FC 2008 Workshop Manual

Diagnostic procedure
(1) Check the battery
zIs the voltage higher than 9V?
Yes: make next operation,
No: The voltage of battery is too low, check the charging/discharging system.
zRefer to chapter 1, Inspection of battery, charging system
(2) Check the wiring harness between battery and safety boox.
zDisassemble fuse panel to set ignition switch at ON position without loosening connector.
zMeasure whether the voltage of related two pins of fuse panel is more than 9V?
Yes: make next step
No: check and repair the wiring harness.
(3) Check the wiring harness between fuse panel and the connector of safety airbag system unit.
Warning:
If the treatment is wrong, safety airbag assembly might be triggered to unfold to make heavy
human hurt, so, before the treatment, it is necessary to read repairing warnings carefully.
Refer to repairing warning of safety airbag system.
a. Set ignition switch at LOCK position,
b. Loosen the cathode cable of battery and keep this state for one minute at least,
c. Disassemble the shell body of steering column,
d. Loosen the connector of helix cable,
e. Disassemble glove box (with safety airbag assembly at the side of passenger),
f. Loosen the connector of safety airbag assembly at the side of passenger,
g. Disassemble left inner trim board,
h. Loosen the connectors of all safety airbag system units,
i. Assemble cathode cable of battery, and set the ignition switch at ON position, then measure
whether the voltage of safety airbag system unit and grounding connector pin is more than 9V?
Yes: make next step,
No: change the wiring harness.
j. Set the ignition switch at LOCK position,
Loosen the cathode cable of battery and keep this for one minute at least.
k . Disassemble left inner trim board,
l. Cut off the conversion connector of safety airbag system unit,
m. Assemble cathode cable of battery, and set the ignition switch at ON position, then measure
whether the voltage of safety airbag system unit and grounding connector pin is more than 9V?
Yes: malfunction diagnosis ends,
No: change the wiring harness.
Supplemental restraint system--Remove malfunction
 254 

(4) Check the wiring harness between helix cable and electronic control unit of safety airbag system
a. Set ignition switch at LOCK position,
b. Loosen the cathode cable of battery and keep this state for one minute at least,
c. Disassemble glove box (with safety airbag assembly at the side of passenger),
d. Loosen the connector of safety airbag assembly at the side of passenger,
e. Disassemble left inner trim board,
f. Loosen the connectors of all safety airbag system units,
g. Check the wiring harness between connector pole of safety airbag system unit and helix cable
connector pin.The wiring harness between safety airbag system at the side of passenger unit con-
nector pin and helix cable connector pin has following situation:
zEarth
zShort connection with power supply
zShort circuit
h. Are the wiring harnesses above normal?
i. Normal: malfunction diagnosis ends, assemble all parts
j. Abnormal: change the wiring harness.
6. Malfunction at the side of passenger
Diagnostic procedure
(1) Check the connector of safety airbag assembly at the side of passenger
zIf the treatment is wrong, safety airbag assembly and pre-tension safety belt might be triggered to
unfold to make heavy human hurt, so, before the treatment, it is necessary to read repairing
warnings carefully.
Refer to repairing warning of safety airbag system.
Malfunction of safety airbag at the side of passenger (resistance is too big or too
small, short circuit, grounding and so on)
Test conditionWarning
zIf the treatment is wrong, safety airbag assembly and pre-tension safety belt might be
triggered to unfold to make heavy human hurt, so, before the treatment, it is necessary
to read repairing warnings carefully. Refer to repairing warning of safety airbag system.
zThe resistance between connector pin 13 and pin 14 of safety airbag system unit is not
in regulated scope.
zThe wiring harness between connector pin 13 and pin 14 of safety airbag system unit
happens short circuit.
Possible reason
zSafety airbag assembly at the side of passenger has malfunction.
zConnector between safety airbag assembly at the side of passenger and electronic con-
trol unit of safety airbag system has malfunction.
zConnector between safety airbag system unit and grounding position has malfunction.
zThe circuit between safety airbag assembly at the side of passenger and electronic
control unit of safety airbag system happens open circuit or short circuit.
zCircuit between safety airbag system unit and grounding position happens open circuit
or short circuit.
zSafety airbag system unit has malfunction.Supplemental restraint system--Remove malfunction
 256 

a. Set ignition switch at LOCK position,
b. Loosen the cathode cable of battery and keep this state for one minute at least,
c. Disassemble glove box,
d. Loosen the connector of safety airbag assembly at the side of passenger,
e. Is the connector of safety airbag assembly at the side of passenger normal?
Normal: make next step,
Abnormal: change the wiring harness
(2) Confirm malfunction reason is on safety airbag assembly at the side of passenger or on other parts.
a. Connect a good assembly on connector pin A and B of safety airbag assembly at the side of
passenger,
b. Connect the cathode cable of battery,
c. Set the ignition switch at ON position,
d. Is there the display of malfunction code? Or could the malfunction code be removed?
No: make next step
Yes: change the safety airbag assembly at the side of passenger.
Refer to safety airbag system, disassembling/assembling of safety airbag assembly at the side of
passenger.
(3) Check the wiring harness between safety airbag assembly at the side of passenger and electronic
control unit of safety airbag system.
a. Set ignition switch at LOCK position,
b. Loosen the cathode cable of battery and keep this state for one minute at least,
c. Disassemble the shell body of steering column,
d. Loosen the connector of helix cable,
e. Loosen the connector of safety airbag assembly at the side of passenger and driver,
f. Disassemble left inner trim board,
g. Loosen the connectors of all safety airbag system units,
h. Check the circuit between connector pin of safety airbag system electronic control unit and the
circuit between connector pin of safety airbag assembly at the side of passenger, and the circuit
between connector pin of safety airbag system unit and safety airbag assembly at the side of
passenger has following situation:
zEarth
zShort connection with power supply
zOpen circuit
i. Are the wiring harnesses above normal?
Normal: malfunction diagnosis ends
Abnormal: change related wiring harness.
Supplemental restraint system--Remove malfunction
 257 

Safety airbag assemble at the side of passenger
1. Note (referring to chapter 1).
2. Use the flash or malfunction diagnostic tool to test the malfunction (referring to chapter
1 and 3).
3. Disconnect the connection of cathode of battery, and do not operate in 60 seconds after
disconnecting.
4. Disassemble the glove box.
5. Disassemble the joint of safety airbag at the side of passenger, and do not damage
airbag wiring harness carefully.
6. Disassemble the safety airbag assembly at the side of passenger.
a. Disassemble three connecting bolts from the bracket of safety airbag assembly at the side of passenger.
b. Take down the safety airbag assembly from panel.
7. Check the safety airbag assembly at the side of passenger (referring to chapter 2).
8. Assemble airbag assembly.
a. Check whether the connection between safety airbag module and airbag short wiring harness is firm.
b. Firstly, insert the module in assembling position from the upside of panel, secondly, align the assem-
bling hole of small bracket on module with the assembling hole on framework of panel, at the same
time, the module cover and panel clearance should be even, and the barb on module should be con-
nected to its position.
9. After assembling, use malfunction diagnostic tool or malfunction indicating light to
check and confirm the malfunction has been removed.
(3) Make three fixed claws mesh steering column.
When changing with new helix cable, it is necessary to disassemble yellow clamp before assembling.
(4) Insert the plug of airbag wiring harness in the plug of helix cable and make this connection firm.
Align the
mark Supplemental restraint system--Disassemble and assemble
 263 
(4) After assembling, use malfunction diagnostic tool or malfunction indicating light to check
and confirm the malfunction has been removed. (5) Connect the lower cover of combination switch.
(6) Connect the upper cover of combination switch with the
lower cover with special bolts firmly.
13. Set the helix cable at middle position
a. Check whether ignition switch locates OFF state.
b. Check whether the cathode end of battery has been
disassembled.
Note: do not operate in 60 seconds after disassembling
cathode end.
c. Turn helix cable anticlockwise with hand until it could not
be turned.
d. Then turn the helix cable clockwise for 2.5 circles to align
the mark.
14. Assemble steering wheel
(1) Inspection before assembling:
z Steering wheel
z Connecting wiring harness
z Safety airbag assembly at the side of driver
(2) Tighten the assembling screws at both sides.
(3) Connection of battery terminal “-”.

2. Only scrap airbag module
1. Explosion of safety airbag assembly at the side of driver.
(1) Prepare a battery as detonating power (12±1)V.
(2) Disassemble safety airbag assembly at the side of driver, and connect the airbag short wiring harness
on gas generator.
Warning: when storing safety airbag module at the side of driver, it is necessary to keep upper
surface face upwards.
Supplemental restraint system--Scrap treatment for safety airbag
(7) Safety airbag assembly at the side of driver after explosion should be scraped by the scrap main points.
Note: Firstly, confirm whether there are people on automobile and near the automobile, do
not operate until confirming none there.
After the safety airbag at the side of driver is unfolded, its gas generator temperature is
high, do not make any treatment until putting it for over 30 minutes to wait for it be-
comes cool.
If safety airbag assembly at the side of driver could not be unfolded, it is necessary to
contact with local appointed repairing station.
3. Safety airbag assembly at the side of passenger.
(1) Disassemble the glove box.
(2) Disassemble the connector between airbag short wiring harness and airbag wiring harness.
(3) Connect the conversion wiring harness of safety airbag with one wiring harness with over 10 m used
for unfolding, and the connecting part should be twisted with insulation adhesive tape to insulate and
prevent from wrong unfolding for static.
(4) Connect conversion wiring harness of safety airbag on yellow joint of helix cable, then lead it out of
automobile with unfolding wiring harness (see following figure).
 265 
(5) Close all windows and doors, and assemble automobile
cover.
(6) Cut off the joint of wiring harness used for unfolding of safety
airbag assembly at the side of driver at the place apart from
the automobile, then connect it with two ends of battery
taken from automobile to make it unfold (see following figure).
(7) Safety airbag assembly at the side of driver after explosion
should be scraped by the scrap main points.
Note:Firstly, confirm whether there are people on automobile and near the automobile, do not
operate until confirming none there.
After the safety airbag at the side of driver is unfolded, its gas generator temperature is
high, do not make any treatment until putting it for over 30 minutes to wait for it be-
comes cool.
If safety airbag assembly at the side of driver could not be unfolded, it is necessary to
contact with local appointed repairing station.
Cover of automobile body
Wiring harness for explosion

Audio system--Outdoor antenna
Outdoor antenna
Change
1. Disassemble battery negative wire
2. Put the front tyre forward
3. Disassemble safety airbag assembly at the side of the driver
4. Disassemble steering wheel
5. Disassemble integration instrument cap
6. Disassemble integration instrument
7. Disassemble panel NO.3 air outlet
8. Disassemble panel NO.1 air outlet
9. Disassemble panel center air outlet trim board
10. Disassemble glove box
11. Disassemble right front pillar trim board
12. Disassemble left front pillar trim board.
13. Disassemble the joint of the safety airbag at the side of the passenger
14. Disassemble panel
15. Disassemble right front door trim board.
16. Disassemble right side trim board.
17. Disassemble antenna assembly [67000136]
(a) Take removable antenna pillar plug apart from radio.
18. Assemble antenna assembly [67000136]
19. Assemble panel
20. Assemble helix cable.
21. Assemble steering wheel
22. Inspect steering wheel whether it dead against the center.
23. Inspect horn button.
24 Assemble horn button
25. Inspect SRS warning light
 312