fog light GEELY MK 2008 Workshop Manual

Table of Contents IV Section 7 Rear Brake Drum ............................................................................................ 4-99
Section 8 Parking Brake System.......................................................................................4-106Part V Electric System & AccessoryChapter 1 Starting and Charging System......................................................................... 5-1
Section 1 Starting System (MR479Q, MR479QA, MR481QA) ...................................... 5-1
Section 2 Charging System (MR479Q, MR479QA, MR481QA) .................................... 5-3
Chapter 2 Combination Instrument System..................................................................... 5-7
Section 1 Wiring diagram of Combination Instrument and Location of Multi-pin Plug-in Terminal5-7
Section 2 Malfunction Symptom Table and Troubleshooting ......................................... 5-10
Chapter 3 Wiper and Washer System............................................................................... 5-21
Section 1 Wiper and Washer System Inspection ........................................................... 5-21
Section 2 Replacement and Adjustment ........................................................................ 5-23
Chapter 4 Light System...................................................................................................... 5-26
Section 1 Light System Introduction ............................................................................... 5-26
Section 2 Light System Malfunction Inspection ............................................................. 5-28
Section 3 Headlamp Replacement ................................................................................. 5-34
Section 4 Front Fog Lamp Replacement ...................................................................... 5-35
Section 5 Rear Combination Lamp Replacement .......................................................... 5-36
Section 6 High-mounted Stop light Replacement .......................................................... 5-36
Section 7 Front Reading Lamp Replacement ................................................................ 5-37
Section 8 Rear Reading Lamp Replacement ................................................................. 5-37
Section 9 License Plate Lamp Replacement ................................................................. 5-37
Chapter 5 Audio System..................................................................................................... 5-38
Section 1 Audio System Description .............................................................................. 5-38
Section 2 Audio System Connector Terminal Layout ..................................................... 5-40
Section 3 Audio System Inspection ................................................................................ 5-41
Section 4 Audio System Replacement ........................................................................... 5-52
Chapter 6 SRS (Supplemental Restraint System)............................................................ 5-54

Table 3 Power Performance Parameter
Table 4 Economic Performance ParameterUnit
km/h
s
s
km/h
% Item Name
Maximum vehicle speedAcceleration time within the fourth gear from 30km/h to 120km/hAcceleration time from 0-100km/hMinimum stable vehicle speed within the fourth gearMaximum gradeability No.
1
2
3
4
5Unit
L/100km
L/100km
m Item Name
Fuel consumption at constant speed (60km/h)
Fuel consumption at constant speed (90km/h)Coasting distance (fully loaded, initial speed 50km/h)No.
1
2
3JL7132U JL7152U JL7162UJL7132HU JL7152HU


/JL7132U JL7152U JL7162UJL7132HU JL7152HU
4.5
550Brief Introduction of Geely MK - Vehicle Configuration2-3Section 2 Vehicle ConfigurationType
Common color
Uncommon color
Exterior
device
Seat Interior
deviceItem NameNo.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19Standard Comfortable Luxury
Firry red Firry red
Titanium silver Body colorChinese red, snow mountain white, pearl black, sky blue, ribbon silver
Crystal diamond silver, golden sand green, pineapple yellowFront chromeplated trim molding
Diamond-shape headlight
Crystal diamond taillight
Highly penetrable front fog light
Green heat insulating four-door glass
Scuff strip with same color as that of the body
Aluminum alloy wheel rim
Tire (185/60R15) (with spare tire)
Retractive antenna (A pillar)
Bumper with same color as that of the bodyLight color (T)deep color(S)mixed color(R)interior trimCentral control panel
A/C outlet vent + trim ring
Chromeplated inner handle
Sun shade (with ticket folder)
High-grade flannelette
Luxury leatherFront seat headrest front and rear angle/height adjustable function
/ /
20
2522
16.5 18
20165
33
28 30155 175 165 155
306.25.1
4.65.0
4.7
6.7
6.36.6 6.2
550 550
550 550 / /
/ / / /

3. Definition of multi-pin plug-in unit terminal
1. Prompt:
R- red Bl- blue Y - yellow B- black P- pink G- green W- white
O- orange Gr - gray Br- brown V- purple Lg- olive drab
The first letter indicates primary color
The second letter indicates stripe colorTerminal
number1 MIL C 10 NA
2 Engine oil pressure switch YG 1 P
3 Brake fluid GR 2 R
4 Park G 3 N
5 Right turn light GB 4 D
6NA 52
7 EBD 6 L
8 Charge WR 7
9NA 8NA
10 NA 9 Sidelight GW
11 Safety belt YR 10 Start BR
12 NA 11 B+
13 Engine GY 12IG ( + ) Y
14 Safety gasbag RY 13 GND
15 NA 14 NA
16 IG ( + ) 15Speed sensor earthing B
1 NA 16 Speed signal input YR
2 Left turn light GW 17 Speed sensor power supply RY
3 High beam (+) RB 18 Key (ODO/TRIP) G
4 High beam (-) RW 19 Key (adjust brightness) YG
5 Foglight Gr 20 Key COM B
6 Rear defrost YB 21 Fuel gauge V
7 NA 22 ABS R
8 NA 23 Tachometer BBL
9 Door-lock warning lamp RBL 24 Coolant temperature gauge YWA
BCCombination Instrument System -Wiring diagram of Combination Instrument and Location of Multi-pin Plug-in Terminal5-9Definition of terminalConductor
ColorTerminal
numberDefinition of terminalConductor
Color

Suspected area
1. Wiring harness or connector
2. ECM
3. Combination instrument assy.
1. Wiring harness or connector
2. Alternator
3. Combination instrument assy.
1. Wiring harness or connector
2. Manual brake switch
3. Combination instrument assy.
1. Wiring harness or connector
2. Brake fluid level switch
3. Combination instrument assy.
1. Wiring harness or connector
2. ABS ECU or ABS warning lamp driving module
3. Combination instrument assy.
1. Wiring harness or connector
2. Airbag ECU controller
3. Combination instrument assy.
1. Wiring harness or connector
2. Airbag ECU controller
3. Combination instrument assy.
1. Wiring harness or connector
2. Front head light dimmer switch
3. Combination instrument assy.
1. Wiring harness or connector
2. Front head light dimmer switch
3. Combination instrument assy.
1. Wiring harness or connector
2. Rear defrost switch
3. Combination instrument assy. 8. Warning lamp fails
Symptom
Check that engine warning lamp does not
illuminate
Charge warning lamp does not illuminate
Park braking warning lamp does not
illuminate
Brake failure warning lamp does not
illuminate
ABS warning lamp does not illuminate
SRS warning lamp does not illuminate
Passenger's airbag indicator lamp does
not illuminate
High beam indicator lamp does not
illuminate
Rear foglight indicator lamp does not
illuminate
Rear defrost indicator lamp does not
illuminate5-16Combination Instrument System -Malfunction Symptom Table and Troubleshooting

5-209. Check park warning lamp
(1) Disconnect connector from park switch
(2) Turn ignition switch to ON, park brake warning lamp should go out.
(3) Use conductor to short connector terminal to ground, park brake warning lamp should illuminate.
10. Check park switch
(1) Disconnect connector from park switch
(2) Pull up manual brake, check whether its terminal is connected with ground
Pull up manual brake: on
Manual brake release: off
11. Brake fluid level warning lamp
(1) Disconnect connector from brake fluid level sensor
(2) Turn ignition switch to ON, brake fluid level warning lamp should go out.
(3) Use conductor to connect its connector terminal wiring harness terminals directly, brake fluid level
warning lamp should illuminate.
12. Check brake fluid level warning switch
(1) Remove tank cap
(2) Disconnect connector from tank
(3) Check whether terminals are connected.
Floater on top: off
(4) Use sucker to suck out liquid from tank
(5) Check whether terminals are connected.
Floater down: on state
(6) Pour liquid back into tank
13. Rear defrost indicator lamp
(1) Turn ignition switch to ON, and start up engine
(2) Push down defrost switch, now rear defrost indicator lamp should illuminate
(3) Turn ignition switch to OFF, rear defrost indicator lamp should go out
14. Rear foglight indicator lamp
When rear foglight illuminates, rear foglight indicator lamp should illuminate, now A5 terminal should be high
potential.
15. Safety belt warning indicator lamp
(1) Disconnect safety belt switch connector from driver side, now safety belt warning indicator lamp should
go out.
(2) Short connector terminal to ground, safety belt warning indicator lamp should illuminate.Combination Instrument System -Malfunction Symptom Table and Troubleshooting

Chapter 4 Light SystemSection 1 Light System IntroductionI. Composition Light system comprises external illumination and signal system and internal illumination system.
The function of the external illumination and signal system is to illuminate the road ahead and send signals
to other vehicles.
The internal illumination system provides internal illumination for driver and passengers.II. Precaution for service1. Precaution when repairing electrical equipments
Disconnect the battery ground cable.
2. Precaution when replacing a headlamp bulb
(1) Before replacing a halogen bulb, turn the headlamp OFF to make it cool.
(2) When installing a new halogen bulb, do not touch the glass part of the bulb with bare hands.
(3) If there is oil stain on the surface of halogen bulb (headlamp and front fog lamp) when the lamps are
turned ON, its service life will be shortened.
(4) Halogen bulbs (headlamp and front fog lamp) have pressurized gas inside and require special handling.
They can explode if dropped to ground. The glass fragments will splash up.
(5) When replacing, make sure to use the bulbs with the same power, same model.
(6) After the bulb is installed, make the lamp holder tight.III. Bulb specificationsRemark: All bulbs are made by Philips Corp..Light System-
Light System Introduction5-26Name Specifications
Headlamp (High beam and Low beam) H1 12V 55W
Turn signal lamp PY21W 12V 21W
Position lamp W5W 12V 5W
Front fog lamp H3 12V 55W
Rear combination lamp (Turn signal lamp) PY21W 12V 21W
Rear combination lamp (Brake / Position lamp) P21/5W 12V 21/5W
Rear combination lamp (Rear fog lamp) P21W 12V 21W
Rear combination lamp (Back-up lamp) P21W 12V 21W
Interior lamp (dome lamp) R5W 12V 5W
Rear row reading lamp C5W 12V 5W
Side turn signal lamp W5W 12V 5W
High mounted stop lamp (incl. rear trunk lamp) W5W 12V 5W
License plate lamp W5W 12V 5W
Door courtesy lamp W5W 12V 5W

IV. Location of light systemRear reading light
High-mount stoplight
Rear combination light
Rear license light
Front reading light ( power sunroof )
Side turn light
Front foglight Front combination lightRear Radar
SensorLight System -Light System Introduction5-27

Symptom
Front fog lamp dose not light up with light control
switch HEADLAMP (Head lamp is normal).
Only one side front fog lamp dose not lightSuspected Area
1. Fog lamp fuse
2. Front fog lamp relay
3. Light switch assembly
4. Harness
1. Bulb
2. HarnessSection 2 Light System Malfunction InspectionSuspected Area
1. Bulb
2. LH or RH headlamp fuse
3. Harness
1. Lamp switch assembly
2. Harness
1. Bulb
2. LH or RH headlamp fuse
3. Harness
1. Lamp switch assembly
2. Harness
1. Lamp switch assembly
2. Harness
1. Bulb
2. Harness
1. Bulb
2. Harness
1. Fuse
2. Light control switch
3. Harness
1. Beam control switch
2. Harness2. Front fog lamp systemSymptom
"Low beam" dose not light (One side)
"Low beam" dose not light (All)
"High beam" dose not light (One side)
"High beam" dose not light (All)
Light dose not flash (Dimmer)
Headlamp is dim
Only one side tail lamp lights
Tail lamps on both sides do not light (Headlamp
is normal)
Tail lamps on both sides do not light (Headlamp
is abnormal)Light System -Light System Malfunction Inspection5-28I. Light system problem symptoms table: Description:
The table below can help you find the causes of malfunction. These figures show the most possible
malfunctions in order of priority. Inspect each part in the order given. If necessary, repair or replace these parts.
1. Headlamp and tail lamp

Symptom
Rear fog lamp dose not light up with light control
switch on FRONT FOG LAMP (Small lamp is
normal).
Rear fog lamp dose not light up with light control
switch on FRONT FOG LAMP (Small lamp is
abnormal).
Only one side rear fog lamp dose not lightSuspected Area
1. Bulb
2. Light switch assembly
3. Harness
1. Bulb
2. Tail lamp fuse
3. Harness
1. Bulb
2. Harness 3. Rear fog lamp system
Symptom
"Hazard" and "Turn" does not work
Hazard warning lamp does not work (Turn is
normal)
Hazard warning lamp is abnormal (Hazard is
abnormal)
Turn signal dose not light up in one direction
Only one bulb dose not light upSuspected Area
1. HAZARD Fuse
2. Central controller
3. Harness
1. Hazard warning switch
2. Harness
1. Turn signal switch
2. Harness
1. Turn signal switch
2. Harness
1. Bulb
2. Harness
Symptom
Brake lamps on both sides do not light up
Brake lamp remains always ON
Brake lamp dose not light (One side)
High mounted Brake lamp dose not light up
(Stop lamp is normal)4. Turn signal and hazard warning system
5. Brake lamp system
Suspected Area
1. Brake lamp fuse
2. Brake lamp switch
3. Harness
1. Brake lamp switch
2. Harness
1. Bulb
2. Harness
1. Bulb
2. HarnessLight System -Light System Malfunction Inspection5-29

Headlight combination switch position drawingII. Lighting system troubleshooting1. Headlight combination switch assemblyHandle positionTerminal
FU TL TR
Turn
light
switchR
NL
LEL2 FF RF
Foglight
switchOFF
FF
RFE L T N S HEAD
Headlight,
small
light
switchOFF
P
HEL1 HL HU
Light
switchPASS
HL
HUPASSSwitch position Testing terminal Status
OFF EL-TNS OFF
Position light EL-TNS ON
Headlight EL-HEAD ON (1) Check whether headlight light control switch is ON
Check whether terminals are connected when switch is in each position according to the table. If it doest not meet stipulation, replace the switch.Light System -Light System Malfunction Inspection5-31Handle positionTerminalHandle positionTerminalHandle positionTerminalHeadlight combination switch shifting diagram