fog light GEELY MK 2008 User Guide

Switch motion Testing terminal Status
ON
1-2 ON
(gear lever is in reverse gear)
OFF 1-2 OFFSwitch position Testing terminal Status
OFF EL2-FF-RF OFF
Front foglight EL2-FF ON
Rear foglight EL2-FF-RF ONSwitch position Testing terminal Status
Low beam EL1-HL ON
High beam EL1-HU ON
PASSING EL1-HU-PASS ON (2) Check whether headlight dimmer switch is connected
Check whether terminals are connected when switch is in each position according to the table.
If it does not meet stipulation, replace the switch.
(3) Check whether direction indicator switch is connected
Check whether terminals are connected when switch is in each position according to the table.
If it doest not meet stipulation, replace the switch.
(4) Check whether front and rear foglight switch is connected
Check whether terminals are connected when switch is in each position according to the table.
If it doest not meet stipulation, replace the switch.
2. Reversing light switch assembly
Check whether reversing light switch assembly is connected
Check whether two terminals are connected when switch works
according to the tableSwitch position Testing terminal Status
Left turn FU-TL ON
Straight ahead FU-TL-TR OFF
Right turn FU-TR ON
If it doest not meet stipulation, replace the switch.
3. Brake lamp switch assembly
Check whether brake lamp switch assembly is connected
Check whether two terminals are connected when brake lamp
switch works
If it doest not meet stipulation, replace the switch.Step down brake pedal 1-2 ON
Release brake pedal 1-2 OFF2 1Light System -Light System Malfunction Inspection5-321
2 ON
OFFRelease PushSwitch motionTesting terminal Status

9. Front foglight relay
Check whether front foglight relay is connected
(1) Check whether terminals are connected
check terminal Testing terminal Status
86-85 ON
30-87 OFF If it doest not meet stipulation, replace the relay.
(2) Apply storage battery voltage (10V-14V) between terminal 86 and 85, then check whether terminal 30 and
87 are connected, if not connected, replace the relay.Electrical connectorI. Removal1. Remove front bumper (see bumper replacement).
2. Remove 4 setscrews of front head light (as shown in the figure).
3. Remove electrical connector.
4. Move carefully forward, upward, remove front head light assembly.II. Installation1. Install electrical connector of front head light assembly.
2. Install front head light assembly and 4 setscrews.
3. Install front bumper.
4. Adjust vehicle state.
5. Adjust front head light beam.Section 3 Headlamp Replacement86
8687 30Light System -Headlamp Replacement5-34

Section 4 Front Fog Lamp ReplacementI. Removal1. Remove front bumper. (see bumper replacement)
2. Remove electrical connector.
3. Remove fixed bolt (as shown in the figure).
4. Remove front foglight assembly.II. Installation1. Install front foglight assembly.
2. Mount fixed bolt.
3. Mount electrical connector.
4. Mount front bumper.
5. Adjust vehicle state.
6. Adjust front foglight beam.III. Replacement of front head light bulb Remove dust shield by rotating anticlockwise
Pull out bulb plug
Press and loosen steel wire clip
Pull out lamp holder, take off bulb
Replace bulbLight System -Front Fog Lamp Replacement5-351-Turn light dust shield
2-Low beam dust shield
3-High beam, front position lamp dust shieldIII. Replacement of front foglight bulb1. Press and rotate anticlockwise, take off dust hood
2. Take out bulb
3. Replace bulbIV. Adjustment of front foglight beam1. Adjust tire pressure in standard value
2. Start up engine
3. Turn on foglight switch
4. Adjust foglight beam turn screw to adjust foglight beam in the vertical direction.
Description:
Turn screwdriver anticlockwise to make beam upward, or turn screwdriver clockwise to make it downward.