warning GENESIS GV60 2023 Owners Manual
[x] Cancel search | Manufacturer: GENESIS, Model Year: 2023, Model line: GV60, Model: GENESIS GV60 2023Pages: 690, PDF Size: 14.07 MB
Page 272 of 690
5-81
05
Power Liftgate
Power liftgate operating conditions
The power liftgate operates when
the gear is in P (Park) with the vehicle
running. However, the power liftgate will
operate regardless of the gear position
when the vehicle is off. Also, the liftgate
can be opened only when vehicle speed
is below 1.8 mph (3 km/h).
For safety, before attempting to open or
close the liftgate, make sure the vehicle
is in P (Park).
WARNING
[ Never leave children or animals
unattended in your vehicle. Children
may operate the power liftgate.
Doing so can result in injury to
themselves or others and can
damage the vehicle.
2 - : ( 9
Page 273 of 690
5-82
Convenience Features
[ Do not operate the power liftgate
under the following conditions.
The power liftgate may not operate
properly.
-One side of the vehicle is lifted to
inspect the vehicle or change a tire
-Parking on an uneven road such as
a slope, etc.
[ Close the liftgate completely and
lock all doors and liftgate using the
central door lock button before using
an automatic car wash.
[ Do not spray high pressure water
directly on the power liftgate outside
open/close button. The liftgate may
open unintentionally. Information
[ If the liftgate is not fully closed and
vehicle speed is at or above 1.8 mph (3
N P K D Z D U Q L Q J Z L O O V R X Q G W L P H V
Immediately park the vehicle at a safe
place, close the liftgate, and check
that the liftgate open warning on the
instrument cluster is turned off.
[ In cold and wet climates, the outside
S R Z H U O L I W J D W H R S H Q F O R V H E X W W R Q P D \
not work properly due to freezing
conditions. If this occurs, remove the
ice before using the outside power
O L I W J D W H R S H Q F O R V H E X W W R Q R U X V H W K H
S R Z H U O L I W J D W H R S H Q F O R V H E X W W R Q R Q W K H
smart key or the instrument panel.
[ Operating the power liftgate more
than 5 times continuously could cause
damage to the operating motor. If
this occurs, the power liftgate will not
operate to prevent the motor from
overheating. If any of the power liftgate
buttons are pressed to try to open the
liftgate, the chime will sound 3 times,
but the liftgate will remain closed.
Allow the power liftgate system to cool
for about 1 minute before operating the
system again.
Page 275 of 690
5-84
Convenience Features
3 R Z H U O L I W J D W H R S H Q F O R V H E X W W R Q , Q V L G H
the power liftgate)
OJWEV051044N
Press the power liftgate open/close
button. The liftgate opens or closes with
a warning sound.
Power liftgate lock button (Inside the
power liftgate)
OJWEV051045N
Press the power liftgate lock button
while carrying the smart key. The liftgate
closes and locks with a warning sound.
Additionally, all doors will lock.The
liftgate can be closed and locked, and
all doors locked only when the button
is pressed while the ready (
)
indicator is off.
Automatic reverse
During power liftgate operation if the
power liftgate senses any obstacle, the
liftgate will stop or will fully open. The
automatic reverse feature may not
operate properly, or it may operate
unexpectedly under the following
circumstances:
[ The automatic reverse feature may
not detect the resistance if the
detected resistance is below a certain
level, or if the liftgate is almost fully
closed near the latched position.
[ The automatic reverse feature may
operate if a strong impact is applied
with no obstructions placed.
WARNING
Never intentionally place any object
or part of your body in the path of
the power liftgate to make sure the
automatic reverse feature operates.
Serious injury, or damage to the vehicle
or object may occur.
Information
The power liftgate may stop operating if
the automatic reverse feature operates
more than two times while attempting to
open or close the liftgate. If this occurs,
carefully open or close the liftgate
manually, and then after 30 seconds try to
operate the power liftgate automatically
again.
Page 277 of 690
5-86
Convenience Features
Resetting the power liftgate
In some circumstances resetting the
power liftgate operation may need to
be performed. Some instances where
resetting the power liftgate may be
required include:
[ When the 12-volt battery is recharged
[ When the 12-volt battery is reinstalled
after removal or replacement
[ When the related fuse is reinstalled
after removal or replacement
OJWEV051047N
1. With the ready () indicator is off
or on, put the gear in P (Park).
2. Press the power liftgate open/close
inner button (1) simultaneously until a
chime sounds.
3. Slowly close the liftgate manually.
4. Press the power liftgate open/close
outer button (2). The power liftgate
will open with a chime sound. Wait
until the liftgate fully opens to
complete resetting. If the liftgate
stops before it is fully open, resetting
cannot be completed.
Information
If the power liftgate does not operate
properly after the above procedure, have
the system inspected by an authorized.
Emergency liftgate safety release
OJWEV051048N
To unlock and open the liftgate manually
from inside the luggage compartment,
perform the following procedure:
1. Remove the cover at the bottom of
the liftgate.
2. Slide the latch in the direction of the
arrow to unlock the liftgate.
3. Push the liftgate to open.
WARNING
[ For emergencies, be fully aware
of the location of the emergency
liftgate safety release latch in the
vehicle and how to open the liftgate
if you are accidentally locked in the
luggage compartment.
[ No one, including animals, should
be allowed to occupy the luggage
compartment of the vehicle at any
time. The luggage compartment is a
very dangerous location in the event
of an accident.
[ Use the release latch for
emergencies only. Use extreme
caution, especially while the vehicle
is in motion.
Page 280 of 690
5-89
05
Detecting area
OJWEV051051
[ The smart liftgate detecting area
extends approximately 50-100 cm
(20-40 in.) behind the vehicle. If you
are positioned in the detecting area
and are carrying the smart key, the
hazard warning lights will blink and
the chime will sound for about 3
seconds to alert you that the liftgate
will open.
[ The alert stops once the smart key is
moved outside of the detecting area
within the 3 second period.
Information
[ Smart liftgate may not operate
properly if any of the following occur:
-The smart key is close to a radio
transmitter such as a radio station or
an airport which can interfere with
normal operation of the transmitter.
-The smart key is near a mobile two
way radio system or a mobile phone.
-Another vehicle’s smart key is being
operated close to your vehicle.
[ Smart liftgate detecting area may
change when:
-The vehicle is parked on an incline
or slope.
-One side of the vehicle is raised or
lowered relative to the opposite side.
Charging Door
Opening the charging door
OJWEV051052
1. Depress the brake pedal and apply the
parking brake.
2. Turn OFF all switches, shift to P (Park),
and turn OFF the vehicle.
3. Push the charging door where the
triangle symbol (1) is located or press
the button on smart key FOB as well
to open charging door. The charging
door opens only when the vehicle is
unlocked.
4. Open the inlet cover (2).
Page 281 of 690
5-90
Convenience Features
CAUTION
[ Do not try forcibly open the charging
door. If you try to force the charging
door to open, the charging door may
stop working.
[ The charge door rises up when
opened. When opening or closing
the charge door, check the safety
around the outside before opening
or closing. Always be careful not to
bump your face, head, etc. or get
your hands caught.
[ Do not hold the supporting part
(hinge). Be careful as there may be
a risk of vehicle damage or safety
accidents due to deformation of
parts.
[ After closing, double check that it is
completely closed.
[ Make sure that the charge door is
closed well before driving. If the
charge door is not closed correctly,
Mechanical parts attached to the
charge door may be damaged.
[ Make sure the charge door is closed
and the charging door open warning
light on the instrument cluster is
turned off.
[ If you leave the vehicle with the
charge door open, there is a risk of
theft, so be sure to check it.
[ After charging, the inlet cover must
be in place. Closing the charge door
without opening it in place may
damage the machine parts.
[ Do not excessively spray liquid on
the charging door when washing the
car.
Closing the charging door
OJWEV051053
1. After recharging, install the charging
inlet cover.
2. Push the Close button located inner
part of the charging door.
For more details, refer to the Electric
Vehicle Guide provided in the front of
the owner’s manual.
Page 283 of 690
5-92
Convenience Features
Precautions while using the
Head-up Display
[ It may sometimes be difficult to read
information on the head-up display in
the following situations.
- The driver is improperly positioned
in the driver’s seat.
- The driver wears polarizing-filter
sunglasses.
- An object is located above the
head-up display cover
- The vehicle is driven on a wet road.
- Any improper lighting accessory is
installed inside the vehicle, or there
is incoming light from outside of the
vehicle.
- The driver wears glasses.
- The driver wears contact lenses.
When it is difficult to read the head up
display information, adjust the image
height or brightness level from the
Settings menu in the infotainment
system screen.
For detailed information, refer to the
separately supplied infotainment
system manual.
[ For your safety, make sure to stop the
vehicle before adjusting the settings.
[ Do not tint the front windshield glass
or add other types of metallic coating.
Otherwise, the head-up display image
may be invisible.
[ Do not place any accessories on the
crash pad or attach any objects on the
windshield glass.
[ When replacing the front windshield
glass, replace it with a windshield
glass designed for head-up display
operation. Otherwise, duplicated
images may be displayed on the
windshield glass.
WARNING
The Blind-Spot Collision Warning
system warnings on the head-up display
are supplemental. Do not solely depend
on them to change lanes. Always take a
look around before changing lanes.
Information
Head-up Display includes GPL, LGPL,
0 3 / D Q G R W K H U R S H Q V R X U F H O L F H Q V H
softwares. All license notices including
U H O D W H G V R X U F H F R G H D U H S U R Y L G H G D W K W W S
Z Z Z P R E L V F R N U R S H Q V R X U F H O L V W G R
If the driver requests on-board
V R I W Z D U H R S H Q V R X U F H F R G H Y L D 0 2 % , 6 B
[email protected] within 3 years
D I W H U E X \ L Q J W K L V S U R G X F W D & ' 5 2 0 R U
other storage device will be sent with the
minimum cost covering storage device cost
and delivery cost.
Page 290 of 690
5-99
05
High Beam Assist Malfunction
and Limitations
High Beam Assist malfunction
OJWEV051094L
When High Beam Assist is not working
properly, the ‘Check High Beam Assist
(HBA) system’ or ‘Check HBA (High
Beam Assist system’ warning message
will appear and
warning light will
illuminate on the cluster. Have the
vehicle be inspected by an authorized
retailer of Genesis Branded products.
Limitations of High Beam Assist
[ Light from an oncoming or front
vehicle is not detected because of
lamp damage, or because it is hidden
from sight, etc.
[ Headlamp of an oncoming or front
vehicle is covered with dust, snow or
water.
[ There is a lamp that has a similar
shape as a vehicle’s lamp.
[ Headlamps have been damaged or
not repaired properly.
[ Headlamps are not aimed properly.
[ Driving on a narrow-curved road,
curved road, rough road, uphill or
downhill. [ Vehicle in front is partially visible on a
crossroad or curved road.
[ There is a traffic light, reflecting sign,
flashing sign or mirror ahead.
[ There is a temporary reflector or flash
ahead (construction area).
[ The road conditions are bad such as
being wet, iced or covered with snow.
[ A vehicle suddenly appears from a
curve.
[ The vehicle is tilted from a flat tire or
is being towed.
[ Light from an oncoming or front
vehicle is not detected due to
obstacles in the air such as exhaust
fume, smoke, fog, snow, or water spay
or blizzard on the road, or fogging in
the lamp, etc.
Information
For more details on the limitations of the
) U R Q W 9 L H Z & D P H U D U H I H U W R
Page 291 of 690
5-100
Convenience Features
INTERIOR LIGHTS
WARNING
Do not use the interior lights when
driving in the dark. The interior lights
may obscure your view and cause an
accident.
NOTICE
Do not use the interior lights for
extended periods when the vehicle is
turned off or the battery will discharge.
Interior Lamp AUTO Cut
The interior lamps will automatically go
off approximately 20 minutes after the
vehicle is turned off and the doors are
closed. If a door is opened, the lamp
will go off 25 minutes after the vehicle
is turned off. If the doors are locked by
the smart key and the vehicle enters the
armed stage of the theft alarm system,
the lamps will go off five seconds later.
Front Lamps
OJWEV051280N
Front map lamp ():
Touch either icons to turn the map lamp
on or off. This light produces a spot
beam for convenient use as a map lamp
at night or as a personal lamp for the
driver and the front passenger.
Door lamp ():
The front or rear room lamps come on
when the front or rear doors are opened.
When doors are unlocked by the smart
key, the front and rear lamps come on
for approximately 30 seconds as long as
any door is not opened. The front and
rear room lamps go out gradually after
approximately 30 seconds when the
door is closed. However, if the Start/Stop
button is in the ON position or all doors
are locked, the front and rear lamps will
turn off. If a door is opened with the
Start/Stop button in the ACC position
or the OFF position, the front and rear
lamps will stay on for about 5 minutes.
Room lamp (()
[ Press the button to turn ON the room
lamp for the front/rear seats.
Page 297 of 690
5-106
Convenience Features
WARNING
To avoid personal injury from the
windshield wipers, when the vehicle
is running and the windshield wiper
switch is placed in the AUTO mode:
[ Do not touch the upper end of the
windshield glass facing the rain
sensor.
[ Do not wipe the upper end of the
windshield glass with a damp or wet
cloth.
[ Do not put pressure on the
windshield glass.
NOTICE
[ When washing the vehicle, set the
wiper switch in the OFF (O) position
to stop the auto wiper operation. The
wiper may operate and be damaged
if the switch is set in the AUTO mode
while washing the vehicle.
[ Do not remove the sensor cover
located on the upper end of the
passenger side windshield glass.
Damage to system components
could occur and may not be covered
by your vehicle warranty.
[ Because of using a photo sensor,
temporary malfunction could occur
according to sudden ambient light
change made by stone and dust
while driving.
Windshield Washers
ORG3EV051079
In the OFF (O) position, pull the lever
gently toward you to spray washer fluid
on the windshield and to run the wipers
1-3 cycles. The spray and wiper operation
will continue until you release the lever. If
the washer does not work, you may need
to add washer fluid to the washer fluid
reservoir.
Recirculating air when washer fluid
is used
When washer fluid is used, in order to
reduce any objectionable scent of the
washer fluid from entering the cabin,
recirculation mode and air conditioning
are automatically activated depending
on the outside temperature. If you
select fresh mode while the function is
operating, the function will resume after
a certain amount of time. It may not work
in some conditions such as cold weather
or vehicle OFF.
For more details, refer to “Climate
Control Additional Features” section in
this chapter.