GENESIS GV60 2023 Workshop Manual

1-46
Foreword / Starting your Electric vehicle
Indicator Details
Error code
On : Error while charging/ Error during self-diagnosis
Error code Item Cause
E1Control Pilot
communicationVehicle communication error
E2
LeakageCurrent leakage
E3 Charger error
E4
Plug temperaturePlug overtemperature
warning
E5 Plug temperature failure
E6 Charger error
E7 Overcurrent Charging overcurrent warning
E8
Internal
temperatureCharger overheating
E9 Charger error
F1 Relay fusion Charger error
F2Ground
Monitoring/
InterruptPoor grounding of outlet
F3
Switched mode
power supply
power failureSwitched mode power supply
error (voltage failure)
F4Switched mode power supply
error (abnormal voltage)
F5
Control Pilot
voltage errorControl Pilot (-) voltage error
F6 Control Pilot (+) voltage error
F7
Temperature
sensor errorPlug temperature sensor error
F8PCB internal temperature
sensor error

1-47
01
Indicator Details
CHARGE
LEVEL
12 A
10 A
8 A
6 A
The charging current changes whenever the
button (1) is pressed for less than 1 sec with
the charger plugged into an electrical outlet
but not the vehicle.* The control box
ORG3EVQ011075

1-48
Foreword / Starting your Electric vehicle
Status / Diagnosis / Countermeasure
ORG3EVQ011077

[Charging connector plugged into
vehicle (POWER Green ON)

[Plug connected to an electric outlet
(POWER Green ON)
Contact an authorized retailer of Genesis
Branded products.
ORG3EVQ011078
While charging

[Charge indicator (POWER Green ON /
CHARGE Blue ON)

[Charging current
ORG3EVQ011125L
Before plugging charging connector into
vehicle (POWER Green ON, FAULT Red
blink)

[Abnormal temperature

[ICCB (In-Cable Control Box) failure
Contact an authorized retailer of Genesis
Branded products.
ORG3EVQ011125L
Plugged into vehicle (POWER Green ON,
FAULT Red Blink)

[Diagnostic device failure

[Current leakage

[Abnormal temperature
Contact an authorized retailer of Genesis
Branded products.

1-49
01
ORG3EVQ011126L

[Leakage current failure (POWER Green
ON, FAULT Red Blink)

[After disconnecting and reconnecting
the power plug, press and release the
button for 2 seconds or longer to clear
the error.
Contact an authorized retailer of Genesis
Branded products.
ORG3EVQ011127L
Power saving mode

[7-segment display is turned off if there
is no status change for more than 1
minute.
How to Disconnect Portable Charger
(ICCB: In-Cable Control Box)
OJWEVQ011104L
1. Press release button, then remove
charging connector from vehicle inlet.
Information
To prevent charging cable theft,
the charging connector cannot be
disconnected from the inlet when the
doors are locked or the charging connector
is in the ‘Always lock’ mode. Unlock all
doors to disconnect the charging connector
from the inlet.
However, if the vehicle is in the charging
connector’Locking while charging’ mode,
the charging connector automatically
unlocks from the inlet when charging is
completed.
If the charging connector is disconnected
while the release button is not pressed, the
connector and the inlet may be damaged.
For more details, refer to “Charging
Connector ‘Always lock’/‘Locking while
charging’ Mode” in this chapter.
If the release button does not work even
after the all doors are unlocked, pull
emergency cable (located in right side of
cargo area) and press the release button
in the connector to disconnect it from the
vehicle. If the release button still does not
work, consult an authorized retailer of
Genesis Branded products.

1-50
Foreword / Starting your Electric vehicle
Information
Some connectors installed in public
charging stations stop charging by
pressing the charge release button while
charging is locked, and the connector can
be disconnected.
2. Make sure to completely close the
charging door.
OAEE046507N
3. Disconnect the plug from the
household electric outlet. Do not pull
the cable when disconnecting the
plug.
4. Close the protection caps of the
charging connector and the charging
plug to protect them from foreign
substances.
5. If the personal charging connector is
used, store the connector in the cable
compartment.
Precautions for Portable Charger
(ICCB: In-Cable Control Box)

[Use the portable charger that is certified
by Genesis Branded Vehicle.

[Do not try to repair, disassemble, or adjust
the portable charger.

[Avoid use of extension cords but if one
is necessary to reach your outlet keep as
short as possible and it must be a medium
or heavy duty cord rated 15 A or higher.

[Stop using immediately when failure
occurs.
[Do not touch the plug and charging
connector with wet hands.

[Do not touch the terminal part of the AC
charging connector and the AC charging
inlet on the vehicle.

[Do not connect the charging connector
to voltage that does not comply with
regulations.

[Do not use the portable charger if it is
worn out, exposed, or there exists any
type of damage on the portable charger.

[If the ICCB case and AC charging
connector is damaged, cracked, or the
wires are exposed in any way, do not use
the portable charger.

[Do not let children operate or touch the
portable charger.

[Keep the control box free of water.

[Keep the normal charging connector or
plug terminal free of foreign substances.

[Do not step on the cable or cord. Do not
pull the cable or cord and do not twist or
bend it.

[Do not charge when there is lightning.

[Do not drop the control box or place a
heavy object on the control box.

[Do not place an object that can generate
high temperatures near the charger when
charging.

[Charging with the worn out or damaged
household electric outlet can result in a
risk of electric shock. If you are in doubt
to the household electric outlet condition,
have it checked by a licensed electrician.

[Stop using the portable charger
immediately if the household electric
outlet or any components is overheated
or you notice burnt odors.

1-51
01
&+$5*,1*7+((/(&75,&9(+,&/(

1-52
Foreword / Starting your Electric vehicle
How to Start the Vehicle
1. Holding the smart key, sit in the
driver’s seat.
2. Fasten the seat belt before starting
the vehicle.
3. Make sure to engage the parking
brake.
4. Turn OFF all electrical devices.
5. Depress and hold the brake pedal
while pressing the Start/Stop button.
OJWEVQ011034
6. When the ready () indicator is
ON, you can drive the vehicle.
When the ready (
) indicator is
OFF, you cannot drive the vehicle.
Start the vehicle again.
7. Depress and hold the brake pedal and
shift to the desired gear position.
Information
While the charging cable is connected, the
gear cannot be shift from P (Park) to any
other gear for safety reasons.
8. Release the parking brake and slowly
release the brake pedal. Check if the
vehicle slowly moves forward, then
depress the accelerator pedal.
How to Shut Off the Vehicle
1. Hold down the brake pedal while the
vehicle is stopped.
2. While depressing the brake pedal,
shift to P (Park).
3. While depressing the brake pedal,
engage the parking brake.
4. While depressing the brake pedal,
press the Start/Stop button and turn
off the vehicle.
OJWEVQ011035
5. Check if the ready () indicator is
turned OFF on the instrument cluster.
When the ready (
) indicator is
ON and the gear is in a position other
than P (Park), the driver can accidently
depress the accelerator pedal, causing
the vehicle to move unexpectedly.
DRIVING ELECTRIC VEHICLE

1-53
01
Virtual Engine Sound System
The Virtual Engine Sound System (VESS)
generates sound for pedestrians to hear
because there is no sound while the
Electric Vehicle (EV) is operating.

[If the vehicle is in the ready (
)
mode and any gear other than P (Park)
is selected, the VESS will be operated.

[When the gear is shifted to R
(Reverse), an additional warning
sound will be heard.
CAUTION

[The vehicle is much quieter while
driving than a conventional gasoline-
powered vehicle. Be aware of your
surroundings and always drive safely.

[After you park the vehicle or while
you are waiting at a traffic light,
check whether there are children or
obstacles around the vehicle.

[Check if there is something behind
the vehicle when driving in reverse.
Pedestrians may not hear the sound
of the vehicle.
Distance to Empty
OJWEVQ011036E
The distance to empty range displayed
will vary depending upon which
drive mode is selected in Drive Mode
Integrated Control System.
For more information, refer to “Drive
Mode Integrated Control System” in
chapter 6.
When destination is not set

[On average, a vehicle can drive about
198 miles (320 km).

[Under certain circumstances where
the air conditioner/heater is ON,
the distance to empty is impacted,
resulting in a possible distance
range from 186 miles (300 km).
When using the heater during cold
weather or driving at high speed, the
high voltage battery consumes a lot
more electricity. This may reduce the
distance to empty significantly.

[After ‘0 mile’ has been displayed,
the vehicle can drive an additional
2~5 miles (3~8 km) depending on
driving speed, heater/air conditioner,
weather, driving style, and other
factors.

1-54
Foreword / Starting your Electric vehicle

[Distance to empty that is displayed
on the instrument cluster after
completing a recharge may vary
significantly depending on previous
operating patterns.
When previous driving patterns
include high speed driving, resulting
in the high voltage battery using more
electricity than usual, the estimated
distance to empty is reduced. When
the high voltage battery uses little
electricity in ECO mode, the estimated
distance to empty increases.

[ Distance to empty may depend on
many factors such as the charge
amount of the high voltage battery,
weather, temperature, durability of
the battery, geographical features,
and driving style.

[Natural degradation may occur with
the high voltage battery depending
on the number of years the vehicle is
used. This may reduce the distance to
empty.
When destination is set
When the destination is set, the distance
to empty may change. The distance
to empty is recalculated using the
information of the destination. However,
the distance to empty may vary
significantly based on traffic conditions,
driving habits, and condition of the
vehicle.
Tips for Improving Distance to
Empty

[If you operate the air conditioner /
heater too much, the driving battery
uses too much electricity. This
may reduce the distance to empty.
Therefore, it is recommended that
you set the cabin temperature to 72°F
(22°C) AUTO. This setting that has
been certified by various assessment
tests to maintain optimal energy
consumption rates while keeping the
temperature fresh.
Turn OFF the heater and air
conditioner if you do not need them.

[When the heater or air conditioning
system is on the energy consumption
is reduced if recirculation mode is
selected instead of selecting the fresh
mode. The fresh mode requires large
amount of energy consumption as
the outside air has to be re-heated or
cooled.

[When using the heater or air
conditioning system use the DRIVER
ONLY or scheduled air conditioner/
heater function.

[Depress and hold the accelerator
pedal to maintain speed and drive
economically.

[Gradually depress and release the
accelerator pedal when accelerating
or decelerating.

[Always maintain specified tire
pressures.

[Do not use unnecessary electrical
components while driving.

[Do not load unnecessary items in the
vehicle.

[Do not mount parts that may increase
air resistance.

1-55
01
Electric energy economy history
OJWEVQ011105L
In order to check the EV electricity
KLVWRU\VHOHFW
S(9