light GENESIS GV60 2023 Manual PDF

5-60
Convenience Features
3) Two-Way Communication
Programming (For select garage door
openers)
If your garage door opener has the
‘myQ’ logo on its side, your opener
likely has Two-Way Communication
capability. HomeLink has the capability
to establish Two-Way Communication
with your garage door opener. HomeLink
can receive and display “closing”
or “opening” status messages from
compatible garage door openers. At
any time, Home-Link can also recall
and display the last recorded status
communicated by the garage door
opener to indicate your garage door
being “closed” or “opened”.
To check if your garage door opener is
compatible with this feature, refer to
www.homelink.com/compatible/Two-
way-Communication. If your garage
door opener has this functionality, AND
the Two-Way Communication indicators
(4), (6) in the mirror appear while the
garage door is opening/closing, then
no further steps are needed. Two-Way
Communication Programming is already
complete. However, if your garage door
opener has this functionality, AND the
Two-Way Communication indicators (4),
(6) in the mirror DO NOT appear while
the garage door is opening/closing, use
the following instructions to enable this
functionality.
1. In your vehicle, press and hold the
programmed HomeLink button for 2
seconds, then release. Confirm that
the garage door is moving. AFTER it
stops, you will have one minute to
complete the following steps:
ÃA ladder and/or second person may
simplify the following steps.2. On your garage door opener in your
garage, locate the “Learn” button
(usually near where the hanging
antenna wire is attached to the garage
door opener). If there is difficulty
locating this button, reference the
device’s owner’s manual.
3. Press and release the “Learn” button.
4. A light on your garage door opener
may flash, and your Two-Way
Communication indicators (4), (6) in
your vehicle may flash, confirming
completion of the process.
5. Return to the vehicle and firmly
press and release the programmed
HomeLink button to activate
your garage door. The Two-Way
Communication indicators (4), (6)
flash in orange when the door is
moving. Do not make any additional
button presses until AFTER the garage
door has come to a complete stop.
6. Your Two-Way Communication
programming is now complete.
Information
If your garage door opener has Two-
:D\&RPPXQLFDWLRQIXQFWLRQDOLW\
it is possible for HomeLink to stop
functioning the garage door shortly
after initial programming, IF the Two-
:D\&RPPXQLFDWLRQ3URJUDPPLQJ
wasn’t properly completed. This
usually happens after the first 10 times
a programmed HomeLink button is
pressed. If you experience this, completing
the “Programming a New HomeLink
%XWWRQ

5-61
05
4) Canadian Programming
Canadian radio-frequency laws require
transmitter remote signals to “time-
out” (or quit) after a couple seconds of
transmission, which may not be long
enough for HomeLink to pick up the signal
during programming.
If you live in Canada or you are having
difficulties programming a gate operator
or garage door opener by using the
programming procedures, replace
“Programming a New HomeLink Button”
step 3 with the following:
While the HomeLink indicator light (7) is
flashing orange, press and release (“cycle”)
your device’s handheld remote every two
seconds until the HomeLink indicator light
(7) changes from orange to green. You may
now release the hand-held remote button.
Then proceed with “Programming a New
HomeLink Button” step 4.
2. Operating HomeLink®
1) Operating HomeLink®
OJWEV051282N
1. Press and release the desired
programmed HomeLink button (1, 2
or 3).
Information
The HomeLink indicator (7) should
light green, solid or flashing, and your
programmed device should operate.
If your device does not operate, the
HomeLink programming was not
successful, and you’ll need to reprogram
the button.
2) Two-Way Communication Display
Behavior
OJWEV051283N
1. Press and release one of the
programmed HomeLink buttons (1, 2
or 3).
OJWEV051284N
2. The indicator (4) and (6) operates as
below, if your garage door opener
has Two-Way Communication
functionality.

5-62
Convenience Features

[If the indicator (4) flashes in Orange,
it indicates that the garage door is
“Closing”.

[The indicator (4) turns solid green
once the garage door has closed.

[If the indicator (6) flashes in Orange,
it indicates that the garage door is
“Opening”.

[The indicator (6) turns solid green
once the garage door has fully
opened.

[If the indicator (4) or (6) does not
turn to green, it indicates that the
last status of garage door was not
received properly. The HomeLink
mirror tries to receive the last known
status of the garage door for a few
seconds.
3) Recalling Garage Door Status
HomeLink mirror with Two-Way
Communication provides a way to view
the last stored message from the garage
door opener. In order to recall the last
known status of the last activated device,
press the buttons “1 and 2” OR “2 and 3”
simultaneously.

[If the indicator (4) appears solid
Green, it indicates that the last
activated device was “closed”
properly.

[If the indicator (6) appears solid
Green, it indicates that the last
activated device was “open” properly.
3. Erasing HomeLink® Buttons
1) Erasing and Reprogramming a Single
HomeLink® Button:
1. Press and hold the desired HomeLink
button you want to re-program. DO
NOT release the button.
2. The HomeLink indicator light (7) will
illuminate solid green. Release the
button as soon as the HomeLink
indicator light (7) begins to flash
orange, usually about 20 seconds.
3. Proceed with the steps in the
“Programming a New HomeLink
Button” section.
Information
If you do not complete the re-
programming of a new device to the
button, it will revert to the previously
stored programming.
2) The following instructions will erase
ALL HomeLink® programming from
ALL buttons:
OJWEV051285N
1. Press and hold the buttons (1) and (3)
simultaneously.
2. The HomeLink indicator light (7) will
illuminate solid Orange for about 10
seconds.
3. Release the buttons once the
HomeLink indicator light (7) changes
to Green and flashes rapidly.
4. Now all three HomeLink buttons
(1), (2) and (3) are cleared of any
programming.

5-74
Convenience Features
OJWEV051035
If your vehicle is equipped with a vision
roof, you can slide open the power
sunshade and an all-glass roof appears.
Power sunshade
Use the power sunshade to block direct
sunlight coming through the sunroof
glass.
OJWEV051036N
OJWEV051037
The power sunshade can only be
operated when Start/Stop button is in
the ON or START position.

[Push the switch rearward, the power
sunshade automatically slides open.

[Push the sunroof switch forward, the
power sunshade automatically closes.
To stop the power sunshade at any point,
push the switch in any direction.
Information

[The power sunshade can be operated
for approximately 3 minutes after the
6WDUW6WRSEXWWRQLVLQWKH$&&RU2))
position. However, if the front door
is open, the power sunshade cannot
be operated even within the 3 minute
period.

[:ULQNOHVIRUPHGRQWKHSRZHU
sunshade are normal due to material
characteristic.
WARNING

[Adjust the power sunshade when
your vehicle stops. This could result
in loss of control and an accident
that may cause injury, or property
damage.

[Do not leave the vehicle running
and the key in your vehicle with
unsupervised children. Unattended
children could operate the power
sunshade, which could result in
injury.

[Do not sit on the top of the vehicle. It
may cause injury or vehicle damage.
NOTICE
Do not pull or push the power sunshade
by hand as such action may damage
the power sunshade or cause it to
malfunction.
VISION ROOF

5-76
Convenience Features
Resetting the Power Sunshade
OJWEV051036N
In some circumstances resetting the
power sunshade operation may need to
be performed. Some instances where
resetting the power sunshade may be
required include:

[When the 12-volt battery is either
disconnected or discharged

[When the power sunshade fuse is
replaced

[If the power sunshade one-touch
AUTO OPEN/CLOSE operation is not
functioning properlySunroof resetting procedure:
1. It is recommended to perform the
reset procedure with the vehicle in
the ready mode. Start the vehicle in P
(Park).
2. Make sure the power sunshade is in
the fully closed position. If the power
sunshade is open, push the switch
forward until the power sunshade and
is fully closed.
3. Release the switch when the power
sunshade is fully closed.
4. Push the switch forward until the
power sunshade moves slightly. Then
release the switch.
5. Once again push and hold the switch
forward until the power sunshade
slides open and close. Do not release
the switch until the operation is
completed.
If you release the switch during
operation, start the procedure again
from step 2.
Information
If the power sunshade does not reset when
the vehicle battery is disconnected or
discharged, or the power sunshade fuse
is blown, the power sunshade may not
operate normally.

5-78
Convenience Features
Hood
Opening the hood
OJWEV051039
1. Park the vehicle and set the parking
brake.
2. Pull the release lever to unlatch the
hood. The hood should pop open
slightly.
OJWEV051253
3. Go to the front of the vehicle, raise the
hood slightly, push up the secondary
latch (1) inside of the hood center and
lift the hood (2).
After the hood has been lifted halfway,
it will raise completely by itself.
Closing the hood
1. Before closing the hood, check in and
around the vehicle compartment to
ensure the following:
- Any tools or other loose objects
are removed from the motor
compartment area or hood
opening area
- All glove, rags, or other
combustible material is removed
from the motor compartment
- All filler caps are tightly and
correctly installed
2. Lower the hood halfway (lifted
approximately 30 cm (12 in.) from the
closed position) and push down to
securely lock in place. Then double
check to be sure the hood is secure.
If the hood can be raised slightly, it is
not securely locked. Open it again and
close it with more force.
WARNING

[Before closing the hood, ensure
all obstructions are removed from
around the hood opening.

[Always double check to be sure that
the hood is firmly latched before
driving away. Check there is no
hood open warning light or message
displayed on the instrument cluster.
Driving with the hood opened may
cause a total loss of visibility, which
might result in an accident.

[Do not move the vehicle with the
hood in the raised position, as vision
is obstructed, which might result in
an accident, and the hood could fall
or be damaged.

5-79
05
Front Trunk
Opening the front trunk
OJWEV051212

[Open the hood

[Lift up the front trunk cover while
depressing the front trunk lever (1).
Closing the front trunk
Push down the front trunk cover to the
right position.
Information
Available front trunk weight

[25 lbs. (10 kg)
WARNING

[NEVER make an attempt to get inside
the front trunk. It will cause a fatal
injury.

[Before closing the hood, ensure
all obstructions are removed from
around the hood opening. The
hood will rise up or move down
automatically if the height is not
firmly adjusted. Be aware of the
damage caused by the unintended
hood movements.

[Never store cigarette lighters,
propane cylinders, or other
flammable/explosive materials in
the vehicle. These items may catch
fire and/or explode if the vehicle
is exposed to hot temperatures for
extended periods.

5-80
Convenience Features
CAUTION

[Do not exceed the luggage volume
capacity of the front trunk. The
overweighted front trunk can be
severely damaged.

[Do not store the fragile objects in the
front trunk.

[ALWAYS keep the front trunk cover
closed securely while driving. Items
inside your vehicle are moving as fast
as the vehicle. If you have to stop or
turn quickly, or if there is a crash, the
items can be damaged.

[Do not spray water in the front
trunk. Vehicle driving system may
get damaged since the front trunk
is located at the center of motor
compartment.

[Be careful when you store any liquid
in the front trunk. If liquid leak
outside the front trunk, it will cause a
damage to the electric devices in the
motor compartment.

[Do not press the front trunk cover
or place the objects on the front
trunk cover. It may be deformed or
damaged.

[When closing the front trunk cover,
be careful not to touch objects
inside the trunk. Loaded objects or
the front trunk may be deformed or
damaged and the front trunk cover
may be opened during driving due to
poor closing, resulting in joints and
damage.

[Do not store plastic objects in
the front trunk when the outside
temperature is high. If the inside
temperature of the front trunk rises
due to sunlight during hot weather,
the plastic objects may be deformed.

[When the front trunk cover freezes
and does not open, lightly tap or
indirectly warm the front trunk
cover.

[Do not apply excessive force or sharp
instruments the front trunk cover. It
may damage the front trunk cover.
NOTICE
To avoid possible theft, do not leave
valuables in the storage compartments.

5-89
05
Detecting area
OJWEV051051

[The smart liftgate detecting area
extends approximately 50-100 cm
(20-40 in.) behind the vehicle. If you
are positioned in the detecting area
and are carrying the smart key, the
hazard warning lights will blink and
the chime will sound for about 3
seconds to alert you that the liftgate
will open.

[The alert stops once the smart key is
moved outside of the detecting area
within the 3 second period.
Information

[Smart liftgate may not operate
properly if any of the following occur:
-The smart key is close to a radio
transmitter such as a radio station or
an airport which can interfere with
normal operation of the transmitter.
-The smart key is near a mobile two
way radio system or a mobile phone.
-Another vehicle’s smart key is being
operated close to your vehicle.

[Smart liftgate detecting area may
change when:
-The vehicle is parked on an incline
or slope.
-One side of the vehicle is raised or
lowered relative to the opposite side.
Charging Door
Opening the charging door
OJWEV051052
1. Depress the brake pedal and apply the
parking brake.
2. Turn OFF all switches, shift to P (Park),
and turn OFF the vehicle.
3. Push the charging door where the
triangle symbol (1) is located or press
the button on smart key FOB as well
to open charging door. The charging
door opens only when the vehicle is
unlocked.
4. Open the inlet cover (2).

5-90
Convenience Features
CAUTION

[Do not try forcibly open the charging
door. If you try to force the charging
door to open, the charging door may
stop working.

[The charge door rises up when
opened. When opening or closing
the charge door, check the safety
around the outside before opening
or closing. Always be careful not to
bump your face, head, etc. or get
your hands caught.

[Do not hold the supporting part
(hinge). Be careful as there may be
a risk of vehicle damage or safety
accidents due to deformation of
parts.

[After closing, double check that it is
completely closed.

[Make sure that the charge door is
closed well before driving. If the
charge door is not closed correctly,
Mechanical parts attached to the
charge door may be damaged.

[Make sure the charge door is closed
and the charging door open warning
light on the instrument cluster is
turned off.

[If you leave the vehicle with the
charge door open, there is a risk of
theft, so be sure to check it.

[After charging, the inlet cover must
be in place. Closing the charge door
without opening it in place may
damage the machine parts.

[Do not excessively spray liquid on
the charging door when washing the
car.
Closing the charging door
OJWEV051053
1. After recharging, install the charging
inlet cover.
2. Push the Close button located inner
part of the charging door.
For more details, refer to the Electric
Vehicle Guide provided in the front of
the owner’s manual.