stop start GMC C-SERIES 1999 User Guide

yellowblue
2-60 Apply Park Brake Warning Light (Option)
This light warns the driver
that the ignition has been
turned off without applying
the parking brake. The
warning light should come
on, as a check, when you
start the engine.
When it comes on, you will also hear a warning tone.
Leaving the vehicle in this condition could result in your
vehicle moving and will discharge the battery.
Parking Brake Warning Light
This light turns on as a
check when the engine is
first started and any time the
system needs adjustment or
there is a malfunction in the
electric/hydraulic parking
brake system.
When the SERVICE PARK BRAKE light comes on,
you will also hear a warning tone. If this light comes on,
have the system repaired immediately.
CAUTION:
If the SERVICE PARK BRAKE warning light
comes on and the warning tone sounds, your
vehicle can stop suddenly and without further
warning. You or others could be injured. If the
SERVICE PARK BRAKE warning light and the
warning tone come on, pull over to the side of the
road and apply the parking brake immediately.
Parking Brake Indicator Light
Vehicles with hydraulic or
air brakes have a parking
brake indicator light. When
the ignition is on, this light
will come on when you set
your parking brake.
The light will stay on if your parking brake doesn't
release fully.
This light should also come on when you turn the
ignition key to START. If it doesn't come on then, have
it fixed so it will be ready to remind you if the parking
brake is applied or hasn't released fully.
ProCarManuals.com

yellowblue
2-61 Anti-Lock Brake System Warning Light
(Option)
With the anti-lock brake
system, this light will come
on when you start your
engine and it may stay on
for several seconds.
That's normal.
If the light stays on, or comes on when you're driving,
your vehicle needs service. If the PRIMARY BRAKE or
LOW AIR warning light isn't on, you still have brakes,
but you don't have the anti
-lock brake feature. If the
PRIMARY BRAKE and/or LOW AIR warning light is
on, you don't have anti
-lock brakes and there's a
problem with your regular brakes. See ªBrake System
Warning Lightº earlier in this section.
The anti
-lock brake system warning light should come
on briefly when you turn the ignition key to RUN. If the
light doesn't come on then, have it fixed so it will be
ready to warn you if there is a problem.
Engine Coolant Temperature Gage
Gasoline Engine Diesel Engine
This gage shows the engine coolant temperature. If
the gage pointer moves into the red area, your engine
coolant might have overheated and your engine may be
too hot. You should pull off the road, stop your vehicle
and turn off the engine as soon as possible.
See ªEngine Overheatingº in the Index. If you have a
Caterpillar

diesel engine, also see your Caterpillar

Operation & Maintenance Manual.
ProCarManuals.com

yellowblue
4-7
Avoid needless heavy braking. Some people drive in
spurts
-- heavy acceleration followed by heavy
braking
-- rather than keeping pace with traffic. This
is a mistake. Your brakes may not have time to cool
between hard stops. Your brakes will wear out much
faster if you do a lot of heavy braking. If you keep pace
with the traffic and allow realistic following distances,
you will eliminate a lot of unnecessary braking. That
means better braking and longer brake life.
If your engine ever stops while you're driving, brake
normally but don't pump your brakes. If you do, the
pedal may get harder to push down. If your engine
stops, you will still have some power brake assist. But
you will use it when you brake. Once the power assist is
used up, it may take longer to stop and the brake pedal
will be harder to push.
Hydraulic Brake Systems
If your engine stops running, or if your primary brake
system stops working, your vehicle has a reserve power
assist system to help you slow down. Just slowly and
steadily apply the brake pedal until you can safely get
off the road. The pedal will seem harder to push down.
Don't pump the pedal; the system won't work well or at
all that way.You may find that the steering wheel seems hard to turn
when you're turning and braking at the same time. Also,
the PRIMARY BRAKE warning light may come on and
the warning tone may sound. This is normal because the
main hydraulic brake system and power steering both
use the power steering pump. If this ever happens, let up
on the brake pedal a little. When you let up on the brake
pedal in that situation, it lets the steering get a little
more help from the pump.
Anti-Lock Brakes (Option)
Your vehicle may have anti-lock brakes (ABS). ABS is
an advanced electronic braking system that will help
prevent a braking skid.
If your vehicle has anti-lock
brakes, this warning light on
the instrument panel will
come on briefly when you
start your vehicle.
When you start your engine and begin to drive away,
your anti
-lock brake system will check itself. You may
hear a momentary motor or clicking noise while this test
is going on. This is normal.
ProCarManuals.com

yellowblue
4-13

Watch for traffic signs, pavement markings and lines.
If you can see a sign up ahead that might indicate a
turn or an intersection, delay your pass. A broken
center line usually indicates it's all right to pass
(providing the road ahead is clear). Never cross a
solid line on your side of the lane or a double solid
line, even if the road seems empty of
approaching traffic.

Do not get too close to the vehicle you want to pass
while you're awaiting an opportunity. For one thing,
following too closely reduces your area of vision,
especially if you're following a larger vehicle. Also,
you won't have adequate space if the vehicle ahead
suddenly slows or stops. Keep back a
reasonable distance.

When it looks like a chance to pass is coming up,
start to accelerate but stay in the right lane and don't
get too close. Time your move so you will be
increasing speed as the time comes to move into the
other lane. If the way is clear to pass, you will have a
ªrunning startº that more than makes up for the
distance you would lose by dropping back. And if
something happens to cause you to cancel your pass,
you need only slow down and drop back again and
wait for another opportunity.
If other cars are lined up to pass a slow vehicle, wait
your turn. But take care that someone isn't trying to
pass you as you pull out to pass the slow vehicle.

Check your mirrors and start your left lane change
signal before moving out of the right lane to pass.
When you are far enough ahead of the passed vehicle
to see its front in your right outside mirror, activate
your right lane change signal and move back into the
right lane. (Remember that if your right outside
mirror is convex, the vehicle you just passed may
seem to be farther away from you than it really is.)

Try not to pass more than one vehicle at a time on
two
-lane roads. Reconsider before passing the
next vehicle.

Don't overtake a slowly moving vehicle too rapidly.
Even though the brake lamps are not flashing, it may
be slowing down or starting to turn.

If you're being passed, make it easy for the
following driver to get ahead of you. Perhaps you
can ease a little to the right.
ProCarManuals.com

yellowblue
4-16
You can be temporarily blinded by approaching
headlamps. It can take a second or two, or even several
seconds, for your eyes to readjust to the dark. When you
are faced with severe glare (as from a driver who
doesn't lower the high beams, or a vehicle with
misaimed headlamps), slow down a little. Avoid staring
directly into the approaching headlamps.
Keep your windshield and all the glass on your vehicle
clean
-- inside and out. Glare at night is made much
worse by dirt on the glass. Even the inside of the glass
can build up a film caused by dust. Dirty glass makes
lights dazzle and flash more than clean glass would,
making the pupils of your eyes contract repeatedly.
Remember that your headlamps light up far less of a
roadway when you are in a turn or curve. Keep your
eyes moving; that way, it's easier to pick out dimly
lighted objects. Just as your headlamps should be
checked regularly for proper aim, so should your eyes
be examined regularly. Some drivers suffer from night
blindness
-- the inability to see in dim light -- and
aren't even aware of it.
Driving in Rain and on Wet Roads
Rain and wet roads can mean driving trouble. On a wet
road, you can't stop, accelerate or turn as well because
your tire
-to-road traction isn't as good as on dry roads.
And, if your tires don't have much tread left, you'll get
even less traction. It's always wise to go slower and be
cautious if rain starts to fall while you are driving. The
surface may get wet suddenly when your reflexes are
tuned for driving on dry pavement.
ProCarManuals.com

yellowblue
4-17
The heavier the rain, the harder it is to see. Even if your
windshield wiper blades are in good shape, a heavy rain
can make it harder to see road signs and traffic signals,
pavement markings, the edge of the road and even
people walking.
It's wise to keep your wiping equipment in good shape
and keep your windshield washer tank filled with
washer fluid. Replace your windshield wiper inserts
when they show signs of streaking or missing areas on
the windshield, or when strips of rubber start to separate
from the inserts.Driving too fast through large water puddles or even
going through some vehicle washes can cause problems,
too. The water may affect your brakes. Try to avoid
puddles. But if you can't, try to slow down before you
hit them.
CAUTION:
Wet brakes can cause accidents. They won't work
as well in a quick stop and may cause pulling to
one side. You could lose control of the vehicle.
After driving through a large puddle of water or
a vehicle wash, apply your brake pedal lightly
until your brakes work normally.
ProCarManuals.com

yellowblue
4-27

Tie a red cloth to your mirror arm to alert police that
you've been stopped by the snow.

Put on extra clothing or wrap a blanket around you.
If you have no blankets or extra clothing, make body
insulators from newspapers, burlap bags, rags, floor
mats
-- anything you can wrap around yourself or
tuck under your clothing to keep warm.
You can run the engine to keep warm, but be careful.
CAUTION:
Snow can trap exhaust gases under your vehicle.
This can cause deadly CO (carbon monoxide) gas
to get inside. CO could overcome you and kill
you. You can't see it or smell it, so you might not
know it is in your vehicle. Clear away snow from
around the base of your vehicle if any is blocking
your exhaust pipe. And check around again from
time to time to be sure snow doesn't collect there.
Open a window just a little on the side of the
vehicle that's away from the wind. This will help
keep CO out.
Run your engine only as long as you must. This saves
fuel. When you run the engine, make it go a little faster
than just idle. That is, push the accelerator slightly. This
uses less fuel for the heat that you get and it keeps the
battery (or batteries) charged. You will need a
well
-charged battery (or batteries) to restart the vehicle,
and possibly for signaling later on with your headlamps.
Let the heater run for a while.
ProCarManuals.com

yellowblue
6-18
CAUTION:
Gasoline Engines Only: Operating the engine
with the air cleaner/filter off can cause you or
others to be burned. The air cleaner not only
cleans the air, it stops flame if the engine
backfires. If it isn't there, and the engine
backfires, you could be burned. Don't drive with
it off, and be careful working on the engine with
the air cleaner/filter off.
NOTICE:
Gasoline Engines Only: If the air cleaner/filter is
off, a backfire can cause a damaging engine fire.
And, dirt can easily get into your engine, which
will damage it. Always have the air cleaner/filter
in place when you're driving.
Your vehicle may also be equipped with an optional
Filterminder gage. See ªWarning Lights, Gages and
Indicatorsº in the Index.
Automatic Transmission Fluid
When to Check
A good time to have it checked is when the engine oil is
checked. See your Allison Automatic Transmission
Operator's Manual to find out when to change your
transmission fluid and filters.
How to Check and What to Use
The Allison Automatic Transmission Operator's Manual
that came with the vehicle shows how to check the
automatic transmission fluid and what fluid to use.
NOTICE:
Too much or too little fluid can damage your
transmission. Too much can mean that some of
the fluid could come out and fall on hot engine
parts or exhaust system parts, starting a fire. Be
sure to get an accurate reading if you check your
transmission fluid.
ProCarManuals.com

yellowblue
6-68
Electrical System
Add-On Electrical Equipment
NOTICE:
Don't add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle
and the damage wouldn't be covered by your
warranty. Some add
-on electrical equipment can
keep other components from working as
they should.
Headlamp Wiring
The headlamp wiring is protected by a circuit breaker in
the light switch. An electrical overload will cause the
lights to go on and off, or in some cases to remain off.
If this happens, have your headlamp wiring checked
right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by a circuit
breaker inside the motor and a circuit breaker in the fuse
block. If the motor overheats, the wipers will stop until
the motor cools. If the overload is caused by an
electrical problem, be sure to get it fixed.
Fusible Links
A fusible link is a short piece of wire several gage sizes
smaller than the circuit it protects. It will melt in an
overload situation, opening the circuit.
Your starter relay and other circuits have these fusible
links. The size is printed on the insulation. If the insulation
is burned beyond recognition, consult your GM dealer for
the proper size. Replace a fusible link with one of the
same size and insulation type. Fusible link insulation is a
special purpose high
-temperature material.
The hydraulic brake booster motor feed circuit and
starter relay circuit are protected by a fusible link.
Vehicles with a diesel engine have a fusible link for the
intake heater feed circuit. Vehicles equipped with an
electronically controlled diesel engine also have a
fusible link for the engine control unit.
ProCarManuals.com

yellowblue
6-71
Name Circuits Protected
CHAS Exhaust Brake, Air Suspension
Dump Valve, Air Dryer, HYD
ABS ECHU
PARK LP Auxiliary Wiring, Air Conditioner
Controls, Parking Lamps, Turn
Signals, Taillamps, Stoplamps,
Marker Lamps, Trailer Running
Lamps, Lighted Mirrors, Radio
Receiver, Mirror Clearance Lamps
HORN Horn/Diagnostic Connector
PRK BRK Parking Brake Module
FUEL Heated Fuel Filter (Diesel
Engines) or Fuel Pump
(Gasoline Engines)
AXLE Heated Mirrors, Radiator Shutters,
Tw o
-Speed Axle Motor,
Tw o
-Speed Axle Switch
MRKR LP Roof Marker Lamps,
Trailer Marker Lamps,
Marker Lamp RelayName Circuits Protected
CIG/AUX Cigarette Lighter,
Auxiliary Power Jacks
AUX Auxiliary Wiring Relay
IGN RLY/VIN Vehicle Interface Module
(Diesel Engines) or Generator,
Coil, Injectors (Gasoline Engines)
WDO Power Windows
CRNK Starter Relay
IGN SW Instrument Panel Cluster Telltales
AUX Auxiliary Wiring
RDO Radio, Auxiliary Wiring
DR LK Power Door Locks
ProCarManuals.com