engine oil GMC SIERRA 1994 Owner's Guide

This doughnut-shaped logo (symbol) is used on most oil containers to help
you select the correct oil.
You should look for this on
the oil container, and use only those oils that
display
the logo.
GM Goodwrench@ oil
(in Canada, GM Engine Oil) meets all the
requirements for your vehicle.
Engine Oil Additives
Don’t add anything to your oil. Your GM dealer is ready to advise if you
think something should be added.
When to Change Engine Oil
See if any one of these is true for you:
0 Most trips are less than 4 miles (6 km).
0 It’s below freezing outside and most trips are less than 10 miles
(16 km).
0 The engine is at low speed most of the time (as in door-to-door
delivery, or in stop-and-go traffic).
0 You tow a trailer often.
0 Most trips are through dusty places.
The vehicle is frequently operated off-road.
If any
of these is true for your vehicle, then you need to change your oil and
filter
every 2,500 miles (4 000 km) or 3 months - whichever comes first.
If
none of them is true, change the oil and filter every 5,000 miles
(8 000 km) or 12 months - whichever comes first.
What to Do with Used Oil
Did you know that used engine oil contains certain elements that may be
unhealthy for
your skin and could even cause cancer‘? Don’t let used oil stay
on your
skin for very long. Clean your skin and nails with soap and water,
or a good hand cleaner. Wash or properly throw away clothing or rags
containing used engine oil. (See the manufacturer’s warnings about the use
and disposal
of oil products.)
Used
oil can be a real threat to the environment. If you change your own oil,
be sure
to drain all free-flowing oil from the filter before disposal. Don’t
ever dispose
of oil by putting it in the trash, pouring it on the ground, into
sewers, or into streams or bodies
of water. Instead, recycle it by taking it to
a place that collects used oil. If you have
a problem properly disposing of
your used
oil, ask your dealer, a service station or a local recycling center
for help.
6-28
ProCarManuals.com

.-. -1 To remove the air
cleaner filter on
a gas
engine or a 6.5 liter
naturally aspirated
diesel,
turn the wing
nuts to the left.
Remove the cover and
change the filter.
Then, unhook the
cover retaining clips
and push the rear
of
the cover toward the
engine.
Automatic Transmission Nuid
When to Check and Change
A good time to check your automatic transmission fluid level is when the
engine oil is changed. Refer
to the Maintenance Schedule to determine
when to change your fluid. See “Scheduled Maintenance Services”
in the
Index.
How to Check
Because this operation can be a little difficult, you may choose to have this
done at
a GM dealership Service Department.
If you do it yourself, be SLIK to follow all the instructions here, or you could
get a false reading on the dipstick.
6 - 30
ProCarManuals.com

How to Add Fluid
Refer to the Maintenance Schedule to determine what kind of transmission
fluid
to use. See “Recommended Fluids and Lubricants” in the Index.
If the fluid level is low, add
only enough of the proper fluid to bring the
level up to the COLD area for a cold check or the HOT area for a hot check.
It doesn’t take much tluid, generally less than a pint. Don’t overfill. We
recommend you use only fluid labeled DEXRON@-111 or DEXRON@-IIE,
because fluids with that label are made especially for your automatic
transmission. Damage caused by fluid other than
DEXRON@-Ill or
DEXRON@-IIE is not covered by your new vehicle warranty.
After adding fluid, recheck the fluid level as described under “How to
Check.”
When the correct fluid level is obtained, push the dipstick back in all
the way; then flip the handle down to lock the dipstick in place.
Manual Fluid
When to Check
A good time to have it checked is when the engine oil is changed. However,
the fluid
in your manual transmission doesn’t require changing.
How to Check
Because this operation can be a little difficult, you may choose to have this
done at a
GM dealership Service Department.
If you do it yourself, be sure to follow all the instructions here, or you could
get
a false reading.
NOTICE:
Too much or too little fluid can damage your transmission. Too
much can mean that some of the fluid could come out and fall on
hot engine parts or exhaust system, starting a fire. Be sure to get
an accurate reading if
you check your transmission fluid.
Check the fluid level only when your engine is off, the vehicle is parked on
a level place and the transmission is cool enough for you to rest your fingers
on the transmission case.
6-33
ProCarManuals.com

What to use
Refer to the Maintenance Schedule to determine what kind of lubricant to
use. See “Recommended Fluids and Lubricants”
in the Index.
Engine Coolant
The following explains your cooling system and how to add coolant when it
is low. If you have a problem with engine overheating, see “Engine
Overheating”
in the Index.
The proper coolant for your vehicle
will:
Give freezing protection down to -20 OF (-29”C), or -34°F (-37°C) in
Canada and for vehicles with the cold climate option.
Give boiling protection up to 258 OF ( 125 O C).
Protect against rust and corrosion.
Help keep the proper engine temperature.
Let the warning lights and gages work as they should.
What to Use
Use a mixture of one-half clean wuter (preferably distilled) and one-half
antifreeze that meets
“GM Specification 6038-M,” which won’t damage
aluminum parts.
You can also use a recycled coolant conforming to “GM
Specification 6038-M” with a complete coolant flush and refill. If you use
this mixture, you don’t need to add anything else.
6-38
ProCarManuals.com

To Check Brake Fluid
You can check the
brake fluid without
taking off the cap. Just
look at the windows
on the brake fluid
reservoir. The fluid
levels should be above
“MIN.” If they aren’t,
have your brake system checked to see
if there is a leak.
After work
is done on the brake hydraulic system, make sure the levels are
above
“MIN” and below the top of each window.
What to Add
When you do need brake fluid, use only DOT-3 brake fluid - such as
Delco Supreme
ll@ (GM Part No.1052535). Use new brake fluid from a
sealed container only, and always clean the brake fluid reservo\
ir cap before
removing it.
NOTICE:
Don’t let someone put in the wrong kind of fluid. For
example, just
a few drops of mineral-based oil, such as engine
oil, in your brake system can damage brake system parts so
badly that they’ll have to be replaced.
Brake fluid can damage paint, so be careful not to spill brake
fluid
on your vehicle. If you do, wash it off immediately. See
“Appearance Care” in the Index.
6-47
ProCarManuals.com

Fluid Leak Check
After the vehicle has been parked for a while, inspect the surface under the
vehicle for water, oil, fuel or other fluids. Water dripping from the air
conditioning
system after it has been used is normal. If you notice fuel leaks
or fumes, the causes should be found and corrected at once.
Lubrication
Accelerator Control System
Your maintenance schedule will tell you how often the accelerator linkage
pivot points must be lubricated. See “Recommended
Fluids and Lubricants”
in the Tndex for the proper lubricant to use.
Accelerator cables and cruise control cables should not be lubricated.
Any
cab1e.s that are worn or are hard to pull should be replaced.
Hood Latches and Hood Hinge
Your maintenance schedule will tell you how often to lubricate the hood
latch and hood hinge assembly. See “Recommended Fluids and Lubricants”
in the Index for the proper lubricant to use.
Propeller Shaft Slip Splines
See your maintenance schedule to find out how often the. slip splines must
be lubricated. See “Recommended Fluids and Lubricants”
in the Index for
the proper lubricant to use.
Constant Velocity Joints
See your mamtenance schedule to find out how often the constant velocity
joints must be lubricated. See “Recommended Flui-ds and Lubricants”
in the
Index for the proper lubricant to use.
Body
Normal use of your vehicle will cause metal to metal wear at some points on
the cab and body if they are not lubricated.
For exposed surfaces, such as door checks, door lock bolts, lock striker
plates, dovetail bumper wedges, etc., a
thin film of engine oil should be
applied.
The seat adjusters and seat track should be lubricated
with chassis grease.
Door weather strips and rubber hood bumpers should be wiped clean with
a
rubber lubricant.
6-51
ProCarManuals.com

Crankcase Capacity
ENGINE VIN QTY Without Filter*
4.3L Z 4 Quarts (3.8 Liters)
5.7L**
K 4 Quarts (3.8 Liters)
5
.OL
H 4 Quarts (3.8 Liters)
6.5L
Pt -
6.5L st -
6.5L H- -
7 .a* * N 6 Quarts (5.7 Liters)
QTY With Filter*
4.5 Quarts (4.3 Liters)
5 Quarts (4.8 Liters)
5 Quarts (4.8 Liters)
7 Quarts
(6.5 Liters)
7 Quarts (6.5 Liters)
7 Quarts (6.5 Liters)
7 Quarts (6.5 Liters)
After refill, the level MUST be checked as outlined under “\
Engine Oil And
Filter Recommendations’’ in Section
5.
*All quantities are approximate.
**Add one additional quart for C3500
HD Models.
?Oil filter should be changed at EVERY oil change.
Fuel Tank Capacity
TYPE
GasolineDiesel with Short Bed
with Long Bed
Crew Cab Standard
Chassis-Cab Models Standard (Side Tank)
Optional (Rear Tank)
3500
HD Models
Standard (Side Tank)
Optional (Rear Tank)
QUANTITY
26 Gallons (98 Liters) 34 Gallons (128 Liters)
34 Gallons (128 Liters)
23 Gallons (87 Liters)
3 1 Gallons (1 17 Liters)
23 Gallons (87 Liters)
3 1 Gallons (1 17 Liters)
All quantities are for a completely
dry tank and are approximate.
I
6-93
ProCarManuals.com

Service Replacement Part and Filter
Recommendations
- Gas Engines
Engine
VIN
Oil Filter
Air Cleaner Filter
PCV Valve
Spark Plugs*
Fuel Filter Radiator Cap
4.3L
z
PF52
A178CW. CV789C
.CR43TS
GF48
1
RC36
5.OL
H
PF1218T A348C
cv774c
.CR43TS GF48
1
RC36
5.7L
K
PF1218t A348C
cv774c
.CR43TS GF48 1
RC36
“four Wheel Drive Vehicle -use a PF52 oil filter
*Use AC copper-cored resister type spark plugs
Service Replacement Part and Filter
Recommendations
- Diesel Engines
Engine
VIN
Oil Filter
Air Cleaner
Fuel Filter Surge Tank Cap 6.5L
P
PF1218
A9 17C
TP 1006
RC33
6.5L
S
PF1218 A917C
TP 1006
RC33
7.4L
N
PF1218 A348C
cv774c
.CR43TS GF48
1
RC36
6.5L
F*
PF1218 A917C
TP 1006
RC33
“Heavy Duty Emission Engine
Air Conditioning Refrigerants
Not all air conditioning refrigerants are the same. If the air conditioning
system in your vehicle needs refrigerant, be sure the proper refrigerant is
used.
If you’re not sure, ask your GM dealer. For additional information, see
your “Warranty and Owner Assistance Information” booklet.
Air Conditioning Refrigerant Capacity
TYPE
Refrigerant R 134A
QTY
2.25 lbs. (1.020 kg)
6-94
ProCarManuals.com

Explanation Of Scheduled Mainienance Services
Below are explanations of the services listed in the maintenance charts.
The proper fluids and lubricants to use are listed in this section. Make sure
whoever services your vehicle uses these. All parts should be replaced and
all necessary repairs done before you or anyone else drives the vehicle.
1. ENGINE OIL AND OIL FILTER CHANGE“‘ - ALWAYS USE
SJ3 ENERGY CONSERVING I1 (GASOLINE ENGINE) OR CF-4/SH
(DIESEL ENGINE) QUALITY OILS
OF THE PROPER VISCOSITY.
To determine the preferred viscosity oil for your vehicle’s engine (e.g.
SAE 5W-30 or 10W-30), see “Engine Oil”
in the Index.
2. CHASSIS LUBRICATION - Lubricate the front suspension, king
pin bushings, steering linkage, transmission, and transfer case shift
linkage, parking brake cable guides, rear driveline center splines and
front axle propshaft splines, brake pedal springs, and clutch pedal
springs at the intervals specified.
If you have a 3500
HD, lubricate the king pins and king pin bushings,
every
1,500 miles (2500 km) for Maintenance Schedule I, or every
3,000 (5000 km) for Maintenance Schedule 11.
Ball joints and king pin bushings should not be lubricated unless their
temperature
is 10” F (-12”C), or higher. When the weather is cold, let
them warm up before lubrication or
they could be damaged.
Also, be sure
to check all the vehicle fluid levels at this time.
3.
CLUTCH FORK BALL STUD LUBRICATION (5-SPEED
MANUAL TRANSMISSION WITH DEEP LOW
) - Lubricate the
clutch fork ball stud through the fitting
on the clutch housing.
Lubricant must be added “sparingly” to
the fitting, as only .0066 lb.
(.003 kg) is required to lubricate the ball stud surface. Do not add
lubricant more often than the intervals
in the Maintenance Charts. Too
much lubricant will damage the clutch assembly.
4. COOLING SYSTEM SERVICE”’? - Drain, flush and refill system
with new coolant. See “Engine Coolant” in the Index for
the proper
coolant and mixture to use
in your vehicle.
Also inspect the hoses and replace them
if they are cracked, swollen, or
deteriorated. Tighten all hose clamps (except constant tension clamps).
Remove debris and clean the outside of the radiator and air
conditioning condenser. Wash the radiator neck.
To ensure proper
operation, pressure test.
the radiator and cap.
* An Emission Control Service
?A fluid
loss in these systems may indicate a problem. Have them
inspected and repaired at once.
7-18
ProCarManuals.com

24. DRIVE AXLE SERVICE? - Check readfront axle fluid level and
add
as needed. Check constant velocity joints and axle seals for
leaking.
0
0
0
0
Locking differential - Drain fluid at first oil change and refill.
Check fluid level and add
as needed at subsequent oil changes. In
dusty areas, or trailer towing applications drain fluid at every
15,000 miles (24 135 kilometers) and refill.
Standard differential - Check fluid level and add as needed at
every
oil change. In dusty areas, or trailer towing applications,
drain fluid every
15,000 miles (24 I35 kilometers) and refill.
More frequent lubrication may be required on heavy-duty or
off-road use.
3500 HD Models - 3500 HD Models with applications requiring
extreme overload/trdiler tow conditions
and high speed conditions
(above 45 mph (72
kdh)) for extended periods of time must
change drive axle fluid every
3,000 miles (4828 kilometers) or 3
months, whichever comes first, OR must use 75W-140 synthetic
fluid meeting
GM specifications. See “Recommended Fluids and
Lubricants” at the end of this section for the proper fluid to use.
25.
BRAKE SYSTEM INSPECTION-f - When the engine oil is
changed, inspect the lines and hoses for proper hookup, binding, leaks,
cracks, chafing, etc. Check the parking brake adjust, and the fluid level
in the master cylinder. A low fluid level can indicate worn disc brake
pads which may need
to be serviced.
When the wheels are removed for rotation, inspect disc brake pads for
wear and rotors for surfxe condition. Also inspect drum brake linings
for wear and cracks. Inspect other brake parts, including drums, wheel
cylinders, parking brake, etc., at the same time. Remove any
rust or dirt
from the wheel and mounting surfaces before mounting the wheel.
Inspect brakes more often if driving habits or conditions result in
frequent braking.
?A fluid loss in these systems may indicate a problem. Have them
inspected and repaired at once.
7-22
ProCarManuals.com