reset GMC YUKON DENALI 2003 Owner's Manual
[x] Cancel search | Manufacturer: GMC, Model Year: 2003, Model line: YUKON DENALI, Model: GMC YUKON DENALI 2003Pages: 447, PDF Size: 21.97 MB
Page 305 of 447

As in the chart shown previously, SAE 5W-30 is the
only viscosity grade recommended for your vehicle. You
should look for and use only oils which have the API
Starburst symbol and which are also identified as
SAE 5W-30. If you cannot find such SAE 5W-30 oils,
you can use an SAE 1OW-30 oil which has the API
Starburst symbol,
if it's going to be 0°F (-18°C)
or above.
Do not use other viscosity grade oils, such as
SAE 1OW-40 or SAE 20W-50 under any conditions.
Notice: Use only engine oil with the American
Petroleum Institute Certified For Gasoline Engines
starburst symbol. Failure to use the recommended
oil can result in engine damage not covered by
your warranty.
GM Goodwrench@ oil meets all the requirements for
your vehicle.
If you are in an area of extreme cold, where the
temperature falls below
-20°F (-29"C), it is
recommended that you use either an SAE 5W-30
synthetic oil or an SAE OW-30 oil. Both will provide
easier cold starting and better protection for your engine
at extremely low temperatures.
Engine Oil Additives
Don't add anything to your oil. The recommended oils
with the starburst symbol are all you will need for
good performance and engine protection.
When to Change Engine Oil (GM Oil
Life System)
Your vehicle has a computer system that lets you know
when to change the engine oil and filter. This is
based on engine revolutions and engine temperature,
and not on mileage. Based on driving conditions,
the mileage at which an oil change will be indicated can
vary considerably. For the oil life system
to work
properly, you must reset the system every time the oil is
changed.
When the system has calculated that oil life has been
diminished, it will indicate that an oil change is
necessary.
A CHANGE ENGINE OIL message will
come on. Change your oil as soon as possible within
the next two times you stop for fuel. It is possible that,
if
you are driving under the best conditions, the oil life
system may not indicate that an oil change is necessarv
for over a year. However, your engine oil and filter
must be changed at least once a year and at this time
the system must be reset. It is also important
to
check your oil regularly and keep it at the proper level.
If the system is ever reset accidentally, you must
change your oil at
3,000 miles (5 000 km) since your
last oil change. Remember to reset the oil life system
whenever the oil is changed.
5-1
6
Page 306 of 447

How to Reset the CHANGE ENGINE OIL
Message
The GM Oil Life System calculates when to change
your engine oil and filter based on vehic!e
use. Anytime
your oil is changed, reset the system
so it can
calculate when the next oil change is required.
If a
situation occurs where you change your
oil prior to a
CHANGE ENGINE OIL message being turned on, reset
the system.
To reset the CHANGE ENGINE
OIL message, see “GM
Oil Life System” under DIC Operation and Displays
on page 3-43 for vehicles equipped with the DIC, or do
the following:
1. Turn the ignition key to RUN with the engine off.
2. Fully press and release the accelerator pedal three
If the OIL LIFE RESET message flashes for
10 seconds,
the system is reset.
If the system does not reset, try the procedure once
again. If it still does not reset, see your dealer for
service. times
within five seconds.
What to Do with Used Oil
Used engine oil contains certain elements that may be
unhealthy for your skin and could even cause cancer.
Don’t let used oil stay on your skin for very long. Clean
your skin and nails with soap and water, or a good hand cleaner. Wash
or properly dispose of clothing or
rags containing used engine oil. See the manufacturer’s
warnings about the use and disposal of oil products.
Used oil can be a threat
to the environment. If you
change your own oil, be sure
to drain all the oil from the
filter before disposal. Never dispose of oil by putting it
in the trash, pouring it on the ground, into sewers, or into
streams or bodies of water. Instead, recycle it by
taking it to a place that collects used oil. If you have a
problem properly disposing of your used oil, ask
your dealer, a service station or a local recycling center
for help.
Engine Air Cleaner/Filter
The engine air cleanedfilter assembly has an air filter
restriction indicator that lets you know when the engine
air cleaner/filter is dirty and needs to be serviced.
The air filter restriction indicator is located on the air
filter assembly cover. See Engine Compartment
Overview
on page 5-72 for more information on location.
See Part
B: Owner Checks and Services on page 6-10
to determine when to check the air filter restriction
indicator.
5-1 7
Page 307 of 447

The service window (A)
with the percentage scale shows the amount of
engine air cleaner/filter life used.
I I
When both service window (A) and service window (B)
turn orange, replace the engine air cleanedfilter.
After changing the engine air cleaner/filter, press the
button on top of the air filter restriction indicator
to
reset it. Your
engine air cleaner/filter is located in the air filter
housing near the front corner of the engine compartment
on the passenger’s side of the vehicle. See Engine
Compartment Overview
on page 5-12 for more
information on location.
5-1 8
Page 314 of 447

Adding Coolant
If you need more coolant, add the proper DEX-COOL@
coolant mixture
at the surge tank, but only when the
engine
is cool.
1 “J can be burned if you sb... coolant on hot
engine parts. Coolant contains ethylene glycol, and
it will burn if the engine parts are hot
enough. Don’t spill coolant on a hot engine.
When replacing the pressure cap, make sure it is
hand-tight.
Coolant Surge Tank Pressure Cap
The coolant surge tank pressure cap must be fully
installed on the coolant surge tank. See Engine
Compartment Overview on page
5-12 for more
information on location.
Notice: Your pressure cap is a pressure-type cap
and must be tightly installed to prevent coolant
loss
and possible engine damage from overheating.
See “Capacities and Specifications” for more
information.
Engine Overheating
You will find a coolant temperature gage on your
vehicle’s instrument panel. See Engine Coolant
Temperature Gage
on page 3-36. in addition, yoti ill
find a LOW COOLANT, ENGINE COOLANT HOT,
ENGINE OVERHEATED and a REDUCED ENGINE
POWER message in the DIC on the instrument panel.
See DIC Warnings and Messages on page
3-52.
Overheated Engine Protection
Operating Mode
If an overheated engine condition exists and the
REDUCED ENGINE POWER message is displayed, an
overheat protection mode which alternates firing
groups of cylinders helps prevent engine damage.
In
this mode, you will notice a loss in power and engine
performance. This operating mode allows your vehicle to
be driven
to a safe place in an emergency. Driving
extended miles (km) and/or towing a trailer in the
overheat protection mode should be avoided.
Notice: After driving in the overheated engine
protection operating mode, to avoid engine damage,
allow the engine to cool before attempting any repair.
The engine oil will be severely degraded. Repair the cause of coolant
loss, change the oil and reset the oil
life system. See “Engine Oil” in the Index.
5-25
Page 350 of 447

Wheel Alignment and Tire Balance
The wheels on your vehicle were aligned and balanced
carefully at the factory
to give you the longest tire life
and best overall performance.
Scheduled wheel alignment and wheel balancing are
not needed. However,
if you notice unusual tire wear or
your vehicle pulling one way or the other, the alignment
may need
to be reset. If you notice your vehicle
vibrating when driving on a smooth road, your wheels
may need
to be rebalanced.
Wheel Replacement
Replace any wheel that is bent, cracked, or badly rusted
or corroded.
If wheel nuts keep coming loose, the
wheel, wheel bolts and wheel nuts should be replaced.
If the wheel leaks air, replace it (except some
aluminum wheels, which can sometimes be repaired).
See your dealer
if any of these conditions exist.
Your dealer will know the kind of wheel you need.
Each new wheel should have the same load-carrying
capacity, diameter, width, offset and be mounted
the same way as the one it replaces.
If you need to replace any of your wheels, wheel bolts
or wheel nuts, replace them only with new
GM
original equipment parts. This way, you will be sure to
have the right wheel, wheel bolts and wheel nuts
for your vehicle. Using the wrong replacement wheels, wheel
bolts or wheel nuts on your vehicle can be
dangerous. It could affect the braking and handling
of your vehicle, make your tires lose
air and make you lose control. You could have
a collision in which you or others could be
injured. Always use the correct wheel, wheel
bolts and wheel nuts for replacement.
Notice: The wrong wheel can also cause problems
with bearing life, brake cooling, speedometer or
odometer calibration, headlamp aim, bumper height,
vehicle ground clearance and
tire clearance to the
body and chassis.
See
Changing a Flat Tire on page 5-63 for more
information.
5-6 1
Page 392 of 447

Scheduled Maintenance
The services shown in this schedule up to 100,000 miles
(1 66 000 km) should be repeated after 100,000 miles
(166
000 km) at the same intervals for the life of
this vehicle. The services shown at
150,000 miles
(240 000 km) should be repeated at the same interval
after 150,000 miles
(240 000 km) for the life of this
vehicle.
See Part B: Owner Checks and Services
on page 6- 10
and Part C: Periodic Maintenance Inspections on
page 6- 14.
Footnotes
t The U.S. Environmental Protection Agency or the
California Air Resources Board has determined that the
failure to perform this maintenance item will not nullify
the emission warranty or limit recall liability prior to
the completion of the vehicle
s useful life. We, however,
urge that all recommended maintenance services be
performed at the indicated intervals and the
maintenance be recorded.
+ A good time to check your brakes is during tire
rotation. See Brake System Inspection
on page 6-14.
Engine Oil and Chassis Lubrication
Scheduled Maintenance
Change engine oil and filter as indicated by the GM
Oil Life System (or every 12 months, whichever
occurs first). Reset the system.
Your vehicle has a computer system that lets you know
when
to change the engine oil and filter. This is
based on engine revolutions and engine temperature,
and not on mileage. Based on driving conditions,
the mileage at which an oil change will be indicated can
vary considerably. For the oil life system
to work
properly, you must reset the system every time the oil is
changed.
When the system has calculated that oil life has been
diminished, it will indicate that an oil change is
necessary. A CHANGE ENGINE
OIL message will
come on. Change your oil as soon as possible within
the next two times you stop for fuel.
It is possible that, if
you are driving under the best conditions, the oil life
system may not indicate that an oil change is necessary
for over a year. However, your engine oil and filter
must be changed at least once a year and at this time
the system must be reset.
It is also important to
check your oil regularly and keep it at the proper level.
6-5
Page 393 of 447

If the system is ever reset accidentally, you must
change your oil at
3,000 miles (5 000 km) since your
last oil change. Remember
to reset the oil life system
whenever the oil is changed. See Engine Oil on
page
5-13 for information on resetting the system.
An Emission Control Service.
Lubricate chassis components with each engine oil
and filter change.
Lubricate the front suspension, ball joints, steering
linkage, transmission shift linkage and parking brake
cable guides. Ball joints should not be lubricated unless
their temperature is 10°F (-12°C) or higher, or they
could be damaged.
After the services are performed, record the date,
odometer reading and who performed the service on the
maintenance record pages in Part
E of this schedule.
7,500 Miles (12 500 km)
U Check rear/front axle fluid level and add fluid as
needed. Check constant velocity joints and axle seals
for leaking.
page
5-56 for proper rotation pattern and additional
information. (See footnote
+.)
0 Rotate tires. See Tire Inspection and Rotation on
15,000 Miles (25 000 km)
17 Check readfront axle fluid level and add fluid as
needed. Check constant velocity joints and axle seals
for leaking.
page
5-56 for proper rotation pattern and additional
information. (See footnote
+.)
0 Rotate tires. See Tire lnspection and Rotation on
22,500 Miles (37 500 km)
0 Check readfront axle fluid level and add fluid as
needed. Check constant velocity joints and axle seals
for leaking.
page
5-56 for proper rotation pattern and additional
information. (See footnote
+.)
CI Rotate tires. See Tire Inspection and Rotation on
30,000 Miles (50 000 km)
3 Check readfront axle fluid level and add fluid as
needed. Check constant velocity joints and axle seals
for leaking.
page
5-56 for proper rotation pattern and additional
information. (See footnote
+.)
(See footnote t.)
U Rotate tires. See Tire Inspection and Rotation on
U Replace fuel filter. An Emission Control Service.
6-6
Page 434 of 447

........... 3-30
....... 4-13
New
Vehicle Break-In
...................................... 2-18
Normal Maintenance Replacement Parts
............ 5-98
0
Odometer ................................
Oil Off-Road Recovery
............
Engine .............. .............. 5-13
Pressure Gage
.......... .................. 3-40
OIL LIFE RESET ............................................ 3-53
OIL PRESSURE LOW
..................................... 3-53
Older Children. Restraints
................................ 1-48
Online Owner Center
........................................ 7-3
Onstar@ Personal Calling
................................. 2-37
Onstar@ Services
............................................ 2-36
Onstar@ Steering Wheel Controls
...................... 2-37
Onstar@ System
............................................. 2-36
Onstar@ Virtual Advisor
.................................... 2-37
Operating Your All-Wheel-Drive Vehicle
Off
Paved Roads .............................................. 4-1 6
Other Warning Devices
...................................... 3-6
Outlet Adjustment
............................................ 3-25
Outside Automatic Dimming Mirror with Curb
View Assist
............................................. 2-35
Convex Mirror
............................................. 2-34
Heated Mirrors
............................................ 2-35 Outside
(cont.)
Power Mirrors
............................................. 2-34
Overheated Engine Protection Operating Mode
..... 5-25
Owners. Canadian
............................................... ii
Owner’s Information
........................................ 7-11
P
Park (P)
Parking Shifting Out
of
............................................ 2-28
Brake
........................................................ 2-25
Over Things That Burn
................................. 2-29
Parking Brake and Automatic Transmission Park
(P) Mechanism Check
.................................. 6-13
Parking on Hills .............................................. 4-55
Park( P)
Shifting Into
................................................ 2-26
Part
A - Scheduled Maintenance Services ............ 6-4
Part B
- Owner Checks and Services ................ 6-10
Part C
- Periodic Maintenance Inspections .......... 6-14
Part
D - Recommended Fluids and Lubricants .... 6-15
Part E
- Maintenance Record ........................... 6-17
Passenger Air Bag Indicator
............................. 2-33
Passenger Sensing System
.......................... 1-81
PASSENGER
DOOR AJAR ........ ............ 3-56
Passing
............................................. 4-13, 4-53
Passlock@
...................................................... 2-17
Personalization Button
..................................... 3-47
Passenger
Air Bag Status Indicator
................... 3-32
10
Page 436 of 447

Remote Control .............................................. 3-75
Remote Keyless Entry System
............................ 2-4
Remote Keyless Entry System. Operation
............ 2-5
Removing the 50/50 Split Bench Seats
.............. 1-14
Removing the Bench Seat
................................ 1-20
Removing the Flat Tire and Installing
Removing the Spare Tire and Tools
................... 5-64
Replacement Bulbs
......................................... 5-53
Replacing Restraint System Parts After a Crash
..... 1-87
Replacing the Bench Seat
................................ 1-21
Reporting Safety Defects
Canadian Government
................................... 7-9
General Motors
........................................... 7-1 0
United States Government .............................. 7-9
Reprogramming a Single HomeLink@ Button
....... 2-41
Resetting Defaults
........................................... 2-41
Restraint System Check
................................... 6-10
Checking Your Restraint Systems
................... 1-86
Replacing Restraint System Parts
After a Crash
.......................................... 1-87
Checking
.................................................... 1-86
Restraints, Head
............................................... 1-6
Retained Accessory Power (RAP)
...................... 2-19
Returning the Seat to an Upright Position
........... 1-19
Returning the Seatbacks to an Upright Position
...... 1-24
the Spare
Tire
............................................. 5-68
Replacing Brake System Parts
.......................... 5-39
Replacing the
50/50 Split Bench Seat ................ 1-16
Restraint Systems
Replacing Parts
........................................... 1-87 Returning
the Seats to an Upright Position
......... 1-11
Returning the Seat(s) to an Upright Position
....... 1-13
RFA
# BATTERY LOW .................................... 3-56
Right Front Passenger Position, Safety Belts
...... 1-39
RIGHT REAR DOOR AJAR
.............................. 3-56
Roadside
Assistance Program
....................................... 7-5
Rocking Your Vehicle To Get
It Out ................... 4-42
Running Your Engine While You Are Parked
....... 2-30
5
Safety Belt
Safety Belts Reminder
Light
............................... ..... 3-30
Center Passenger Position
............ ..... 1-39
Questions and Answers About Safety Belts
..... 1-29
Care
of
......................................... ..... 5-80
Driver Position
........................................ 1-30
How
to Wear Safety Belts Properly ................ 1-30
Rear Safety Belt Comfort Guides for Children
and Small Adults
...................................... 1-44
Rear Seat Passengers
................................. 1-41
Safety Belt Extender
.................................... 1-47
Safety Belt Use During Pregnancy
............. 1-38
Safety Belts Are for Everyone
................... 1-25
Safety Warnings and Symbols
.............................. III
Scheduled Maintenance ..................................... 6-5
Right Front Passenger
Position
...................... 1-39
Safety Chains
.................................... ..... 4-52 ...
12
Page 437 of 447

Seats
50/50 Split Bench Seat ................................. 1-1 1
60/40 Split Bench Seat
.................................. 1-9
Bench Seat
................................................ 1-17
Bucket Seats,
Rear ...................................... 1-22
Head Restraints ............................................ 1-6
Heated Seats
............................................... 1-4
Heated Seats, Rear
....................................... 1-8
Memory
..................................................... 2-47
Power Lumbar
.............................................. 1-4
Power Seats
................................................. 1-3
Rear Seat Operation
...................................... 1-7
Reclining Seatbacks
...................................... 1-5
Second Row
.................................................. 1-66
Second Row
- Lap-Shoulder Belt ...................... 1-39
Securing a Child Restraint
Center Rear Seat Position
............................ 1-65
Designed for the LATCH System
................... 1-63
Rear Outside Seat Position
........................... 1-63
Right Front Seat Position
.............................. 1-68
Select Button
................................................. 3-44
Service
........................................................... 5-3
Adding Equipment
to the Outside of
Your Vehicle
.............................................. 5-4
Doing Your Own Work
................................... 5-3
Engine Soon Light
.................... , ........... 3-38
Publications Ordering Information
.... ........ 7-10
SERVICE
4WD ............................................ 3-54
SERVICE AIR BAG
......................................... 3-54
Security Light
................................................. 3-41 SERVICE BRAKE
SYSTEM
............................. 3-54
Service Bulletins
............................................. 7-11
Service Manuals
............................................. 7-10
SERVICE RIDE CONTROL
.............................. 3-54
SERVlCE STABILITY ...................................... 3-57
Setting Preset PTYs (RDS Only) ....................... 3-64
Setting Preset Stations
.................................... 3-61
Setting the Time
............................................. 3-58
Setting the Tone (BasslTreble)
.............. ..... 3-62
Sheet Metal Damage
....................................... 5-87
Shifting Into Park (P)
....................................... 2-26
Side Impact Air Bags
....................................... 1-77
Skidding
........................................................ 4-15
Spare Tire
..................................................... 5-81
Specifications, Capacities
............................. 5-96
Speedometer
.................................................. 3-30
Split Bench Seat
(50/50) .................................. 1-11
Split Bench Seat (60140)
.................................... 1-9
Stabilitrak System 4-9
Shifting
Out of
Park (P) ................................... 2-28
Some Other Rainy Weather Tips
....................... 4-31
Spare Tire Check
............................................ 6-11
Speaker Covers
.......................................... 5-80
8 ...........................................
STABILITY SYS ACTIVE .................................. 3-56
STABILITY SYS DISABLED
.............................. 3-57
Starter Switch Check
....................................... 6-12
Starting Your Engine
....................................... 2-19
Steering
........................................................ 4-11
Steering and Suspension Inspection
.................. 6-14
13